50 research outputs found
Interaction between U/UO2 bilayers and hydrogen studied by in-situ X-ray diffraction
This paper reports experiments investigating the reaction of H with
uranium metal-oxide bilayers. The bilayers consist of 100 nm of
epitaxial -U (grown on a Nb buffer deposited on sapphire) with a
UO overlayer of thicknesses of between 20 and 80 nm. The oxides were made
either by depositing via reactive magnetron sputtering, or allowing the uranium
metal to oxidise in air at room temperature. The bilayers were exposed to
hydrogen, with sample temperatures between 80 and 200 C, and monitored via
in-situ x-ray diffraction and complimentary experiments conducted using
Scanning Transmission Electron Microscopy - Electron Energy Loss Spectroscopy
(STEM-EELS). Small partial pressures of H caused rapid consumption of the
U metal and lead to changes in the intensity and position of the diffraction
peaks from both the UO overlayers and the U metal. There is an
orientational dependence in the rate of U consumption. From changes in the
lattice parameter we deduce that hydrogen enters both the oxide and metal
layers, contracting the oxide and expanding the metal. The air-grown oxide
overlayers appear to hinder the H-reaction up to a threshold dose, but
then on heating from 80 to 140 C the consumption is more rapid than for the
as-deposited overlayers. STEM-EELS establishes that the U-hydride layer lies at
the oxide-metal interface, and that the initial formation is at defects or
grain boundaries, and involves the formation of amorphous and/or
nanocrystalline UH. This explains why no diffraction peaks from UH
are observed. {\textcopyright British Crown Owned Copyright 2017/AWE}Comment: Submitted for peer revie
2020 roadmap on solid-state batteries
Li-ion batteries have revolutionized the portable electronics industry and empowered the electric vehicle (EV) revolution. Unfortunately, traditional Li-ion chemistry is approaching its physicochemical limit. The demand for higher density (longer range), high power (fast charging), and safer EVs has recently created a resurgence of interest in solid state batteries (SSB). Historically, research has focused on improving the ionic conductivity of solid electrolytes, yet ceramic solids now deliver sufficient ionic conductivity. The barriers lie within the interfaces between the electrolyte and the two electrodes, in the mechanical properties throughout the device, and in processing scalability. In 2017 the Faraday Institution, the UK's independent institute for electrochemical energy storage research, launched the SOLBAT (solid-state lithium metal anode battery) project, aimed at understanding the fundamental science underpinning the problems of SSBs, and recognising that the paucity of such understanding is the major barrier to progress. The purpose of this Roadmap is to present an overview of the fundamental challenges impeding the development of SSBs, the advances in science and technology necessary to understand the underlying science, and the multidisciplinary approach being taken by SOLBAT researchers in facing these challenges. It is our hope that this Roadmap will guide academia, industry, and funding agencies towards the further development of these batteries in the future
Micro-scale testing of ductile and brittle cantilever beam specimens in situ with a dual beam workstation
Motoring and mobility for disabled people
0.75LD:82/21828(Motoring) / BLDSC - British Library Document Supply CentreSIGLEGBUnited Kingdo
Oxidation and passivation of the uranium nitride (001) surface
The oxidation of uranium mononitride is a potential issue when considering this material as a nuclear fuel. This work investigates the rate and mechanism of this reaction at room temperature, giving insight into fuel surface oxidation during manufacture and storage. Chemical and structural investigation of the ideal surface of an epitaxial (001) UN thin film, shows that a UO2+xNy layer forms on the surface, highlighting the need for better understanding of the U-N-O system. Below this, a U2N3 interlayer is detected. The topotactic formation of these layers is predicted to play a critical role in the passivation measured during long-duration structural investigation
Sodium/Na β″ alumina interface: Effect of pressure on voids
Three-electrode studies coupled with tomographic imaging of the Na/Na-β″-alumina interface reveal that voids form in the Na metal at the interface on stripping and they accumulate on cycling, leading to increasing interfacial current density, dendrite formation on plating, short circuit, and cell failure. The process occurs above a critical current for stripping (CCS) for a given stack pressure, which sets the upper limit on current density that avoids cell failure, in line with results for the Li/solid-electrolyte interface. The pressure required to avoid cell failure varies linearly with current density, indicating that Na creep rather than diffusion per se dominates Na transport to the interface and that significant pressures are required to prevent cell death, >9 MPa at 2.5 mA·cm–2
Sodium/Na β″ alumina interface: effect of pressure on voids
Three-electrode studies coupled with tomographic imaging of the Na/Na-β″-alumina interface reveal that voids form in the Na metal at the interface on stripping and they accumulate on cycling, leading to increasing interfacial current density, dendrite formation on plating, short circuit, and cell failure. The process occurs above a critical current for stripping (CCS) for a given stack pressure, which sets the upper limit on current density that avoids cell failure, in line with results for the Li/solid-electrolyte interface. The pressure required to avoid cell failure varies linearly with current density, indicating that Na creep rather than diffusion per se dominates Na transport to the interface and that significant pressures are required to prevent cell death, >9 MPa at 2.5 mA·cm–2