Three-to-five-phase matrix converter using carrier-based PWM technique

<p><strong>Abstract</strong> - This paper proposes a simple Carrier-Based PWM (CBPWM) technique to control the three- to five-phase Direct Matrix Converter (3×5 DMC). The proposed technique uses the indirect modulation approach to control the 3×5 DMC such as a three-phase bidirectional rectifier followed by five-phase voltage source inverter (VSI). Based on this approach, it is possible to synthesize the desired five-phase output voltages with sinusoidal three-phase input currents and unity input power factor. A CBPWM method is suggested for each stage independently including both linear and overmodulation operating modes. By the proposed technique, in both operating modes, the maximum possible overall Voltage Transfer Ratio (VTR) are achieved. Moreover, this technique allows the input power factor to be controlled by controlling the input current displacement angle. The feasibility of the proposed technique has been verified by a series of simulation and experimental results based on Matlab/Simulink and dSPACE-DS1104 platform. The results show that, a sinusoidal output and input waveforms can be achieved with a maximum possible VTR in the linear region. However, in the overmodulation region, a maximum possible VTR is achieved at the cost of some distortion of output and input waveforms. Therefore, this technique can be used for the application where a higher VTR is essential.</p

SPACE VECTOR PWM TECHNIQUE FOR THREE- TO SEVEN-PHASE AC-TO-AC POWER CONVERTERS: ANALYSIS AND EXPERIMENTAL VERIFICATIONS

This paper presents Pulse Width Modulation (PWM) control technique for three to seven-phase ac-to-ac power converters. These proposed PWM techniques are based on Indirect Space Vector Modulation (ISVM), which model the converter as two independent stages perform rectification and inversion stages. Two schemes of ISVM are proposed. The first scheme maximizes the voltage transfer ratio (VTR) of the converter but it produces unwanted low order harmonics. The second scheme generates sinusoidal output voltage waveforms; the cost is a reduction in the VTR of this configuration in linear mode. The viability of the proposed technique is proved using experimental results

A family of discontinuous PWM strategies for quasi Z-source nine-switch inverters

This paper proposes a new family of discontinuous PWM strategies to control the quasi-Z-source nine-switch inverters (qZS-NSI). The presented strategies provide buck and boost inversion capabilities, and suitable for common-frequency and different-frequency modes of operation. Accordingly, two different shoot-through (ST) approaches are introduced and compared. The first approach uses three-leg ST, while the second uses single-leg ST to reduce the number of switching commutations, therefore minimizing switching losses. Both approaches can be implemented using simple-boost (SB) and maximum boost (MB) control methods. The operating principles, performance criteria, and PWM modulator of each scheme are introduced. Compared to the conventional PWM technique for the same output voltage gains, the proposed schemes ensure continuous input current with minimum ripples, and the voltage stresses on the switching devices and capacitors could be reduced in the proposed MB control schemes. Moreover, the effective switching frequency of upper and lower switches of all schemes is fixed and could be reduced by 1/3 from the switching frequency of the conventional technique of the qZS-NSI, while only the single-leg ST schemes ensure minimum effective switching frequency of the middle switches. The proposed modulation strategies are digitally implemented and tested on the LAUNCHXL-F28379D DSP. The feasibility of the proposed modulation schemes is confirmed via simulation and experimental results, which show good agreement with the theoretical analysis. Moreover, the presented strategies can be applied to other types of Z-source NSIs.Scopu

Modeling and control of a voltage-lift cell split-source inverter with MPPT for photovoltaic systems

In this study, a new single-stage inverter with improved boosting performance was proposed to enhance the recently developed split-source inverter (SSI) topology. The study introduced new SSI configurations with high voltage gain. The proposed design features a voltage-lift cell made of capacitors, inductors, and diodes, which increases the boosting capability. The decoupled control technique, where The DC input current is controlled by the AC modulation signals,allows for independent adjustment of both the DC input and AC output current. The research also employed a modified space vector modulation approach to manage the inverter switches and reduce current ripple. The combination of the proposed topology and the modified SVPWM scheme significantly improves the DC-boosting capabilities. the validity of the proposed solution was confirmed through simulation using three-phase SSI models in MATLAB/SIMULINK®. Finally, The validity of the simulation and experimental investigation of the analysis and performance of the topologies provided

Utilization of LSTM neural network for water production forecasting of a stepped solar still with a corrugated absorber plate

This study introduces a long short-term memory (LSTM) neural network model to forecast the freshwater yield of a stepped solar still and a conventional one. The stepped solar still was equiped by a copper corrugated absorber plate. The thermal performance of the stepped solar still is compared with that of conventional single slope solar still. The heat transfer coefficients of convection, evaporation, and radiation process have been evaluated. The exergy and energy efficiencies of both solar stills have been also evaluated. The yield of the stepped solar still is enhanced by about 128 % compared with that of conventional solar still. Then, the proposed LSTM neural network method is utilized to forecast the hourly yield of the investigated solar stills. Field experimental data was used to train and test the developed model. The freshwater yield was used in a time series form to train the proposed model. The forecasting accuracy of the proposed model was compared with those obtained by conventional autoregressive integrated moving average (ARIMA) and was evaluated using different statistical assessment measures. The coefficient of determination of the forecasted results has a high value of 0.97 and 0.99 for the conventional and the stepped solar still, respectively

Modeling and control of single-stage quadratic-boost split source inverters

This paper aims to develop the recently introduced Spilt-Source Inverter (SSI) topology to improve its boosting characteristics. New SSI topologies with high voltage gain are introduced in this paper. The proposed converters square the basic SSI&#x2019;s boosting factor by utilizing an additional inductor, capacitor, and two diodes. Thus, the proposed converters are called Quadratic-Boost (or Square-Boost) SSIs (QBIs or SBIs). Four different QBI topologies are presented. One with continuous input current (CC-QBI), and the other draws a discontinuous input current (DC-QBI) but with reduced capacitor voltage stresses. This paper also introduces the small-signal model of the CC-QBI using state variables perturbance. Based on this model, the closed-loop voltage and current control approach of the dc-boosting factor are designed. Moreover, a modified space vector modulation (MSVM) scheme is presented to reduce the input current ripples. To evaluate the performance of the proposed topologies, a comparative study between them and the other counterpart from different perspectives is introduced. It can be found that the CC-QBI topology has superior boosting characteristics when operating with low input voltage compared with their counterparts. It has a higher boosting capability, lower capacitor voltages, and semiconductor stresses, especially when high voltage gains are required. These merits make the proposed topologies convenient to the Photovoltaic and Fuel-Cell systems. Finally, the feasibility of the suggested topology and the introduced mathematical model is verified via simulation and experimental results, which show good accordance with the theoretical analysis. AuthorScopu

Complete Genome Sequence and Comparative Analysis of the Fish Pathogen Lactococcus garvieae

Lactococcus garvieae causes fatal haemorrhagic septicaemia in fish such as yellowtail. The comparative analysis of genomes of a virulent strain Lg2 and a non-virulent strain ATCC 49156 of L. garvieae revealed that the two strains shared a high degree of sequence identity, but Lg2 had a 16.5-kb capsule gene cluster that is absent in ATCC 49156. The capsule gene cluster was composed of 15 genes, of which eight genes are highly conserved with those in exopolysaccharide biosynthesis gene cluster often found in Lactococcus lactis strains. Sequence analysis of the capsule gene cluster in the less virulent strain L. garvieae Lg2-S, Lg2-derived strain, showed that two conserved genes were disrupted by a single base pair deletion, respectively. These results strongly suggest that the capsule is crucial for virulence of Lg2. The capsule gene cluster of Lg2 may be a genomic island from several features such as the presence of insertion sequences flanked on both ends, different GC content from the chromosomal average, integration into the locus syntenic to other lactococcal genome sequences, and distribution in human gut microbiomes. The analysis also predicted other potential virulence factors such as haemolysin. The present study provides new insights into understanding of the virulence mechanisms of L. garvieae in fish