Optical VOCs detection using poly(3-alkylthiophenes) with different side-chain lengths

The use of conjugated polymers in the gas and volatile organic compounds (VOCs) detections represents an advance in the development of the electronic noses. Polythiophenes show good thermal and environmental stability, are easily synthesized and they have been studied as gas and VOCs sensors using different principles or transduction techniques. Among these techniques, optical sensing has been attracted attention, mainly due to its versatility. However, conjugated polymer-based optical sensors are still less studied. This paper describes the use of two poly(3-alkylthiophenes) for VOCs optical detection. The sensing measurements were carried out using visible spectroscopy. Both polymers showed good sensitivity to the VOCs, showing fast and reversible responses with some hysteresis, and were unable to detect hydroxylated samples. Furthermore, it was demonstrated that the thickness of polymer films influences the intensity of the optical response. Although there is similarity in the superficial composition of the polymers films, demonstrated by their surface energies, they showed significant differences in their optical properties upon exposure to the VOCs. (c) 2009 Elsevier B.V. All rights reserved.FAPESPFundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)CNPqMinistério da Ciência, Tecnologia e Inovação do Brasil (MCTI)IMMP/MCT ( Brazil

Regioregular improvement on the oxidative polymerization of poly-3-octylthiophenes by slow addition of oxidant at low temperature

Many pathways can be used to synthesize polythiophenes derivatives. The polycondensation reactions performed with organometallics are preferred since they lead to regioregular polymers (with high content of heat-to-tail coupling) which have enhanced conductivity and luminescence. However, these pathways have several steps; the reactants are highly moisture sensitive and expensive. On the other hand, the oxidative polymerization using FeCl3 is a one-pot reaction that requires less moisture sensitive reactants with lower cost, although the most common reaction conditions lead to polymers with low regioregularity. Here, we report that by changing the reaction conditions, such as FeCl3 addition rate and reaction temperature, poly-3-octylthiophenes with different the regioregularities can be obtained, reaching about 80% of heat-to-tail coupling. Different molar mass distributions and polydispersivities were obtained. The preliminary results suggest that the oxidative polymerization process could be improved to yield polythiophenes with higher regioregularity degree and narrower molar mass distributions by just setting some reaction conditions. We also verified that it is possible to solvent extract part of the lower regioregular fraction of the polymer further improving the regioregularity degree. (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012FAPESPFAPESPCNPqCNPqCAPESCAPESINEO/MCT (Brazil)INEO-MCT (Brazil

Enhancement of laser induced Au nanoparticle formation by femtosecond pulse shaping

We report the control of Au nanoparticle (NP) formation by using shaped 30 fs pulses, in a solution containing HAuCl4 and chitosan. By using a sinusoidal spectral phase, a periodic train of pulses is generated. When the period of the pulse train matches certain Raman resonances of chitosan, the reducing agent of the process, an enhancement of the Au NP formation is observed. Theoretical quantum chemical calculations indicate that the outer groups of the chitosan are mostly influenced by low Raman frequencies, which is in reasonably agreement with the experimental data and indicates an enhancement in the Au NP formation as the pulse train period increases (low frequency).FAPESPCNPqCAPE

Manipulation of anchoring strength in an azo-dye side chain polymer by photoisomerization

The generation of surface anisotropy by photochemical means has been proposed as an attractive method to align liquid crystals. In this paper, we present an experimental study of the alignment induced on a liquid crystal by a polymer film containing azo-dye groups in the side chain. Optical measurements were performed in nematic liquid crystal cells to determine the azimuthal and zenithal anchoring strengths as a function of the irradiation energy and chromophores concentration. It was observed that the director tends to align perpendicular to the polarization direction of the incident light and the orientation process consists essentially of a rotation of the director in the plane parallel to the boundary surfaces. However, the concentration of azo-dye groups in the polymer film must exceed a minimum value to get a macroscopical effect on the liquid crystal alignment. It is shown that the azimuthal anchoring strength can be varied two orders of magnitude by controlling the irradiation energy and azo-dye concentration.Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP

Optical storage properties in cast films of an azopolymer

In this paper we discuss the properties of optically induced birefringence in DR19-MDI cast films that may be used in optical storage applications. The selection of DR19-MDI cast films was based on a comparative study of optical storage properties of Langmuir-Blodgett (LB) films from various azopolymers. DR19-MDI possesses a high residual fraction of optical birefringence and good environmental stability, which was corroborated by the data from optical storage experiments. DR19-MDI cast films maintain a reasonable level of birefringence after the initial decay due to chromophore relaxation, thus making them promising candidates for optical storage devices