Linear polyurethanes with imidazoquinazoline rings: preparation and properties evaluation

Abstract: In this work, research concerning the synthesis and properties of linear polyurethanes (PUs) with the imidazoquinazoline rings was represented. Reaction conditions of 2,6-bis(2-hydroxyethyl)-1-phenylimida-zo[1,5-c]quinazoline-3,5-dione (BHPIQ) with 1,6-hexamethylene diisocyanate were determined and optimized. These conditions are adapted to reaction of BHPIQ with 4,4′-diphenylmethane diisocyanate and 2,4-toluene diisocyanate. New PUs with imidazoquinazoline rings were characterized by spectral methods ( 1 H-NMR and IR spectroscopies), which confirm their structures. Their molar masses and dispersity index were measured by size exclusion chromatography method. The wide-angle X-ray scattering and differential scanning calorimetry (DSC) studies have shown that all PUs based on BHPIQ are amorphous. Moreover, thermal properties of PUs were investigated by thermogravimetry analysis, standard DSC, and temperature-modulated DSC methods. During thermogravimetric measurements, the exhaust gases were analyzed by FTIR method. Incorporation of imidazoquinazoline ring into the PU chains escalates their glass transition temperature; thus, their heat resistance was enhanced. Furthermore, their degradation rate and the amount of released degradation products were reduced. The investigated properties of the obtained PUs with imidazoquinazoline rings were compared with those ones of suitable PUs based on 1,4-butanediol. Graphical abstract: Linear polyurethanes were obtained in reaction of 1-phenyl-2,6-bis(2-hydroxyethylimidazo[1,5-c]quinazoline-3,5-dione with hexamethylene 1,6-diisocyanate, 4,4′-diphenylmethane diisocyanate and toluene 2,4-diisocyanate. Their composition and structure were confirmed. The phase contents and thermal properties were investigated[Figure not available: see fulltext.]. © 2019, The Author(s).DS budge

Polymer/layered clay/polyurethane nanocomposites: P3HB hybrid nanobiocomposites - Preparation and properties evaluation

This paper presents an attempt to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU400) and organomodified montmorillonite (MMT)—(Cloisite®30B). The nanostructure of hybrid nanobiocomposites produced by extrusion was analyzed by X-ray diffraction and transmission electron microscopy, and the morphology was analyzed by scanning electron microscopy. In addition, selected mechanical properties and thermal properties were studied by thermogravimetric analysis, TGA, and differential scanning calorimetry, DSC. The interactions of the composite ingredients were indicated by FT IR spectroscopy. The effect of the amount of nanofiller on the properties of prepared hybrid nanobiocomposites was noted. Moreover, the non-equilibrium and equilibrium thermal parameters of nanobiocomposites were established based on their thermal history. Based on equilibrium parameters (i.e., the heat of fusion for the fully crystalline materials and the change in the heat capacity at the glass transition temperature for the fully amorphous nanobiocomposites), the degree of crystallinity and the mobile and rigid amorphous fractions were estimated. The addition of Cloisite®30B and aliphatic polyurethane to the P3HB matrix caused a decrease in the degree of crystallinity in reference to the unfilled P3HB. Simultaneously, an increase in the amorphous phase contents was noted. A rigid amorphous fraction was also denoted. Thermogravimetric analysis of the nanocomposites was also carried out and showed that the thermal stability of all nanocomposites was higher than that of the unfilled P3HB. An additional 1% mass of nanofiller increased the degradation temperature of the nanocomposites by about 30 °C in reference to the unfilled P3HB. Moreover, it was found that obtained hybrid nanobiocomposites containing 10 wt.% of aliphatic polyurethane (PU400) and the smallest amount of nanofiller (1 wt.% of Cloisite®30B) showed the best mechanical properties. We observed a desirable decrease in hardness of 15%, an increase in the relative strain at break of 60% and in the impact strength of 15% of the newly prepared nanobiocomposites with respect to the unfiled P3HB. The produced hybrid nanobiocomposites combined the best features induced by the plasticizing effect of polyurethane and the formation of P3HB–montmorillonite–polyurethane (P3HB-PU-MMT) adducts, which resulted in the improvement of the thermal and mechanical properties. © 2023 by the authors.Ministerstvo Školství, Mládeže a Tělovýchovy, MŠMT: 8J20PL026, RP/CPS/2022/00

Tracking of Thermal, Physicochemical, and Biological Parameters of a Long-Term Stored Honey Artificially Adulterated with Sugar Syrups

The growing phenomenon of honey adulteration prompts the search for simple methods to confirm the authenticity of honey. The aim of the study was to evaluate the changes in thermal characteristics, physicochemical parameters, antioxidant and enzymatic activity of honey subjected to artificial adulteration. Two series of products were prepared with the use of two different sugar syrups with an increasing dosage of adulterant (0 to 30%). After 24 months of storage, the quality of adulterated samples (partially crystallized) was assessed in comparison to the control honey (solid). Used adulteration changed physicochemical parameters and reduced antioxidant and enzymatic activity of honey (p p gs were observed in a wide range from −19.5 °C to 4.10 °C for honeys adulterated by syrup only. In turn, the Tg in range of 50.4–57.6 °C was observed only for the honeys adulterated by invert. These specific Tg seem to be useful to detect honey adulteration and to identify the kind of adulterant used

Polymer/Layered Clay/Polyurethane Nanocomposites: P3HB Hybrid Nanobiocomposites—Preparation and Properties Evaluation

This paper presents an attempt to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU400) and organomodified montmorillonite (MMT)—(Cloisite®30B). The nanostructure of hybrid nanobiocomposites produced by extrusion was analyzed by X-ray diffraction and transmission electron microscopy, and the morphology was analyzed by scanning electron microscopy. In addition, selected mechanical properties and thermal properties were studied by thermogravimetric analysis, TGA, and differential scanning calorimetry, DSC. The interactions of the composite ingredients were indicated by FT IR spectroscopy. The effect of the amount of nanofiller on the properties of prepared hybrid nanobiocomposites was noted. Moreover, the non-equilibrium and equilibrium thermal parameters of nanobiocomposites were established based on their thermal history. Based on equilibrium parameters (i.e., the heat of fusion for the fully crystalline materials and the change in the heat capacity at the glass transition temperature for the fully amorphous nanobiocomposites), the degree of crystallinity and the mobile and rigid amorphous fractions were estimated. The addition of Cloisite®30B and aliphatic polyurethane to the P3HB matrix caused a decrease in the degree of crystallinity in reference to the unfilled P3HB. Simultaneously, an increase in the amorphous phase contents was noted. A rigid amorphous fraction was also denoted. Thermogravimetric analysis of the nanocomposites was also carried out and showed that the thermal stability of all nanocomposites was higher than that of the unfilled P3HB. An additional 1% mass of nanofiller increased the degradation temperature of the nanocomposites by about 30 °C in reference to the unfilled P3HB. Moreover, it was found that obtained hybrid nanobiocomposites containing 10 wt.% of aliphatic polyurethane (PU400) and the smallest amount of nanofiller (1 wt.% of Cloisite®30B) showed the best mechanical properties. We observed a desirable decrease in hardness of 15%, an increase in the relative strain at break of 60% and in the impact strength of 15% of the newly prepared nanobiocomposites with respect to the unfiled P3HB. The produced hybrid nanobiocomposites combined the best features induced by the plasticizing effect of polyurethane and the formation of P3HB–montmorillonite–polyurethane (P3HB-PU-MMT) adducts, which resulted in the improvement of the thermal and mechanical properties

Hybrid nanobiocomposites based on poly(3-hydroxybutyrate) - characterization, thermal and mechanical properties

Poly(3-hydroxybutyrate) is a biopolymer which is used to production of implants in the human body. On the other hand, the physical and mechanical properties of poly(3-hydroxybutyrate) are compared to the properties of isotactic polypropylene what makes poly(3-hydroxybutyrate) possible substitute for polypropylene. Unfortunately, the melting point of poly(3-hydroxybutyrate) is almost equal to its degradation temperature what gives very narrow window of its processing conditions. Therefore, numerous attempts are being made to improve the poly(3-hydroxybutyrate) properties. In the present work, hybrid nanobiocomposites based on poly(3-hydroxybutyrate) as a matrix with the use of organic nanoclay-Cloisite 30B and linear polyurethane as a second filler have been manufactured. The linear polyurethane was based on diphenylmethane 4,4'-diisocyanate and diol with imidazoquinazoline rings. The obtained nanobiocomposites were characterized by X-ray diffraction, scanning and transmission electron microscopies, thermogravimetry, differential scanning calorimetry and their selected mechanical properties were tested. The resulting hybrid nanobiocomposites have intercalated/exfoliated structure. The nanobiocomposites characterize a higher thermal stability and a wider range of processing temperatures compared to the unfilled matrix. The plasticizing influence of nanofillers was also observed. In addition, the mechanical properties of the discussed nanobiocomposites were examined and compared with those ones of the unfilled poly(3-hydroxybutyrate). The new-obtained nanobiocomposites based on poly(3-hydroxybutyrate) containing 1% Cloisite 30B and 5% by mass of the linear of polyurethane characterized the highest improvement of processing conditions. They have the biggest difference between the temperature of degradation and the onset melting temperature, about 100°C. © 2020, Institute of Machine Design and Operation. All rights reserved

Biopolymer Compositions Based on Poly(3-hydroxybutyrate) and Linear Polyurethanes with Aromatic Rings—Preparation and Properties Evaluation

Polymer biocompositions of poly(3-hydroxybutyrate) (P3HB) and linear polyurethanes (PU) with aromatic rings were produced by melt-blending at different P3HB/PU weight ratios (100/0, 95/5, 90/10, and 85/15). Polyurethanes have been prepared with 4,4′-diphenylmethane diisocyanate and polyethylene glycols with molar masses of 400 g/mol (PU400), 1000g/mol (PU1000), and 1500 g/mol (PU1500). The compatibility and morphology of the obtained polymer blends were determined by infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). The effect of the polyurethane content in the biocompositions on their thermal stability and mechanical properties was investigated and compared with those of the native P3HB. It was shown that increasing the PU content in P3HB-PU compositions to 10 wt.% leads to an improvement in the mentioned properties. The obtained results demonstrated that the thermal stability and mechanical properties of P3HB were improved, particularly in terms of increasing the degradation temperature, reducing hardness, and increasing impact strength. The best thermal and mechanical properties were shown by the P3HB-PU polymer compositions containing 10 wt.% of polyurethane modifiers, especially PU1000, which was also confirmed by the morphology analysis of these biocompositions. The presence of polyurethanes in the resulting polymer biocomposites decreases their glass transition temperatures, i.e., makes the materials more flexible. The resulting polymer biocompositions have suitable mechanical properties and thermal properties within the processing conditions for the predicted application as biodegradable, short-lived products for agriculture

Stepwise Glucoheptoamidation of Poly(Amidoamine) Dendrimer G3 to Tune Physicochemical Properties of the Potential Drug Carrier: In Vitro Tests for Cytisine Conjugates

Third-generation poly(amidoamine) dendrimer (PAMAM) was modified by stepwise primary amine group amidation with d-glucoheptono-1,4-lactone. The physicochemical properties of the conjugates—size, ζ potential in lysosomal pH 5 and in neutral aqueous solutions, as well as intramolecular dynamics by differential scanning calorimetry—were determined. Internalization and toxicity of the conjugates against normal human fibroblasts BJ were monitored in vitro in order to select an appropriate carrier for a drug delivery system. It was found that initial glucoheptoamidation (up to 1/3 of amine groups of neat dendrimers available) resulted in increase of conjugate size and ζ potential. Native or low substituted dendrimer conjugates accumulated efficiently in fibroblast cells at nontoxic 1 µM concentration. Further substitution of dendrimer caused consistent decrease of size and ζ potential, cell accumulation, and toxicity. All dendrimers are amorphous at 36.6 °C as determined by differential scanning calorimetry (DSC). The optimized dendrimer, half-filled with glucoheptoamide substituents, was applied as carrier bearing two covalently attached cytisine molecules: a rigid and hydrophobic alkaloid. The conjugate with 2 cytisine and 16 glucoheptoamide substituents showed fast accumulation and no toxicity up to 200 µM concentration. The half-glucoheptoamidated PAMAM dendrimer was selected as a promising anticancer drug carrier for further applications

The cytisine-enriched poly(3-hydroxybutyrate) fibers for sustained-release dosage form

The polymeric cytisine-enriched fibers based on poly(3-hydroxybutyrate) were obtained using electrospinning method. The biocompatibility study, advanced thermal analysis and release of cytisine from the poly(3-hydroxybutyrate) fibers were carried out. The nanofibers' morphology was evaluated by scanning electron microscopy. The formation and description of phases during the thermal processes of fibers by the advanced thermal analysis were examined. The new quantitative thermal analysis of polymeric fibers with cytisine phases based on vibrational, solid and liquid heat capacities was presented. The apparent heat capacity of fibers was measured using the standard differential scanning calorimetry. The quantitative analysis allowed for the study of the glass transition and melting/crystallization process. The mobile amorphous fraction, degree of crystallinity and rigid amorphous fraction were determined depending on the thermal history of semicrystalline polymeric fibers. Furthermore, the cytisine dissolution behaviour was studied. It was observed that the kinetic of the release from polymeric nanofiber is delayed than for the marketed product. The immunosafety of the tested polymeric nanofibers with cytisine was confirmed by the Food and Drug Agency Guidance as well as the European Medicines Agency. The polymeric matrix with cytisine seems to be a promising candidate for the prolonged release formulation. © 2023Ministerstvo Školství, Mládeže a Tělovýchovy, MŠMT: RP/CPS/2022/002; Narodowe Centrum Nauki, NCN: 2019/03/X/NZ7/00888; Narodowym Centrum Nauki, NC