A device for rapid determination of thermophysical properties of phase-change wind-tunnel models

An experimental method for direct measurement of the thermophysical properties of wind tunnel heat transfer models was developed. The technique consists of placing the model under a bank of high intensity, radiant heaters so that the fast opening water cooled shutters, which isolate the heater bank from the model, allow a step-input heat rate to be applied. Measurements of the heat transfer rate coupled with a surface-temperature time history of the same material are sufficient to determine the material thermophysical properties. An infrared thermometer is used to measure model surface temperature and a slug calorimeter provides heat transfer rate information. The output from the infrared thermometer and calorimeter is then fed into an analog-to-digital converter which provides digitized data to a computer. This computer then calculates combined thermophysical properties and a teleprinter prints out all the data. Thus, results are available within 7 minutes of test initiation as opposed to the weeks or months required using prior techniques

Sound shield

An improved test section for a supersonic or hypersonic wind tunnel is disclosed wherein the model tested is shielded from the noise normally radiated by the turbulent tunnel wall boundary layer. A vacuum plenum surrounds spaced rod elements making up the test chamber to extract some of the boundary layer as formed along the rod elements during a test to thereby delay the tendency of the rod boundary layers to become turbulent. Novel rod construction involves bending each rod slightly prior to machining the bent area to provide a flat segment on each rod for connection with the flat entrance fairing. Rods and fairing are secured to provide a test chamber incline on the order of 1 deg outward from the noise shield centerline to produce up to 65% reduction of the root mean square (rms) pressure over previously employed wind tunnel test sections at equivalent Reynolds numbers

Experimental investigation at Mach 8 of the effects of projections and cavities on heat transfer to a model of the Viking aeroshell

An experimental investigation into the aerodynamic heating on a Mars entry vehicle shape with several types of local surface distortion is presented. The configurations tested were 0.033-scale models of a spherically blunted 70 deg half-angle cone with two protuberances of different length, representing the tube leading to the gas chromograph mass spectrometer, and two aeroshell-bioshield attachment points of different size. These models were tested at free-stream Reynolds numbers per meter of 3.7 million and 17 million over an angle-of-attack range from 0 to 18 deg in the Langley Mach 8 variable density hypersonic tunnel. The phase change-coating technique was used to measure heat transfer coefficient. The long protuberance caused more severe interference heating than the short protuberance for the same conditions. When the short projection was located close to the edge of the aeroshell, the interference heating was greater than that on the same projection when located near the vertex. A significant increase in heat transfer coefficient was measured only on the larger aeroshell-bioshield attachment point

Apparatus for determining thermophysical properties of test specimens

Apparatus is described for directly measuring the quantity square root of pck of a test specimen such as a wind tunnel model where p is density, c is the specific heat and k is the thermal conductivity of the specimen. The test specimen and a reference specimen are simultaneously subjected to the heat from a heat source. A thermocouple is attached to the reference specimen for producing a first electrical analog signal proportional to the heat rate Q that the test specimen is subjected to and an infrared radiometer that is aimed at the test specimen produces a second electrical analog signal proportional to the surface temperature T of the test specimen. An analog-to-digital converter converts the first and second electrical analog signals to digital signals. These digital signals are applied to a computer for determining the quantity

Automated electronic system for measuring thermophysical properties

Phase-charge coatings are used to measure surface temperature accurately under transient heating conditions. Coating melts when surface reaches calibrated phase-charge temperature. Temperature is monitored by infrared thermometer, and corresponding elapsed time is recorded by electronic data-handling system

Noise reduction in a Mach 5 wind tunnel with a rectangular rod-wall sound shield

A rod wall sound shield was tested over a range of Reynolds numbers of 0.5 x 10 to the 7th power to 8.0 x 10 to the 7th power per meter. The model consisted of a rectangular array of longitudinal rods with boundary-layer suction through gaps between the rods. Suitable measurement techniques were used to determine properties of the flow and acoustic disturbance in the shield and transition in the rod boundary layers. Measurements indicated that for a Reynolds number of 1.5 x 10 to the 9th power the noise in the shielded region was significantly reduced, but only when the flow is mostly laminar on the rods. Actual nozzle input noise measured on the nozzle centerline before reflection at the shield walls was attenuated only slightly even when the rod boundary layer were laminar. At a lower Reynolds number, nozzle input noise at noise levels in the shield were still too high for application to a quiet tunnel. At Reynolds numbers above 2.0 x 10 the the 7th power per meter, measured noise levels were generally higher than nozzle input levels, probably due to transition in the rod boundary layers. The small attenuation of nozzle input noise at intermediate Reynolds numbers for laminar rod layers at the acoustic origins is apparently due to high frequencies of noise

Aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing at Mach number 0.2

A wind-tunnel of the static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing was conducted in the Langley low-turbulence pressure tunnel. The configuration variables included wing planform, tip fins, center fin, and scramjet engine modules. A mach number of 0.2 was investigated over a Reynolds number (based on fuselage length) range of 2,200,000 to 19.75 x 1,000,000 (with a majority of tests at 10.0 x 1,000,000. Tests were conducted through an angle-of-attack range from about -2 deg to 34 deg at angles of sideslip of 0 deg to 5 deg, and at elevon deflection of 0 deg, -5 deg, -10 deg, -15 deg, and -20 deg. The drag coefficient of the integrated scramjet engine appears relatively constant with Reynolds number at the test Mach number of 0.2. Mild pitch-up was exhibited by the models equipped with tip fins. The forward delta, a highly swept forward portion of the wing, was destabilizing. The center fin model has a higher trimmed maximum lift-drag ratio and a wider trim lift and angle-of-attack range than the tip fin model. Both the tip fin models and center fin models exhibited positive dihedral effect and positive directional stability. Roll control was positive for the tip fin model, but yaw due to roll control was unfavorable

Correlations of supersonic boundary-layer transition on cones including effects of large axial variations in wind-tunnel noise

Transition data on sharp tip cones in two pilot low disturbance wind tunnels at Mach numbers of 3.5 and 5 were correlated in terms of noise parameters with data from several conventional wind tunnels and with data from supersonic flight tests on a transition cone. The noise parameters were developed to account for the large axial variations of the free stream noise and the very high frequency noise spectra that occurred in the low disturbance tunnels for some test conditions. The noise could be varied in these tunnels from high levels, approaching those in conventional tunnels, to extremely low levels. The correlations indicated that transition in the low disturbance tunnels was dominated by the local stream noise that was incident on the cone boundary layer unstream of the neutral stability point. The correlation results also suggested that high frequency components of the low disturbance tunnel noise spectra had significant effects on transition when the noise was incident on the boundary layer both upstream and downstream of the neutral stability point

Low-speed aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing

An experimental investigation of the low-speed static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept delta wing was conducted in a low-speed tunnel with a 12-foot (3.66 meter) octagonal test section. Aircraft component variations included: (1) fuselage shape modifications, (2) tip fins, (3) center vertical fin, (4) wing camber, and (5) wing planform. This investigation was conducted at a dynamic pressure of 262.4 Pa (5.48 psf), a Mach number of 0.06, and a Reynolds number of 2.24 million, based on body length. Tests were conducted through an angle-of-attack range of 0 deg to 30 deg with elevon deflections from +5.0 deg to minus 30.0 deg. The complete configuration exhibited positive static longitudinal, lateral and directional stability up to angles of attack of at least 20 deg and was trimmable to lift coefficients of at least 0.70 with elevon deflections of minus 30 deg

Free-stream noise and transition measurements on a cone in a Mach 3.5 pilot low-disturbance tunnel

A small scale Mach 3.5 wind tunnel incorporating certain novel design features and intended for boundary-layer-transition research has been tested. The free stream noise intensities and spectral distributions were determined throughout the test section for several values of unit Reynolds number and for nozzle boundary layer bleed on and off. The boundary layer transition location on a slender cone and the response of this to changes in the noise environment were determined. Root mean square free stream noise levels ranged from less than one tenth up to values approaching those for conventional nozzles, with the lowest values prevailing at upstream locations within the nozzle. For low noise conditions, cone transition Reynolds numbers were in the range of those for free flight; whereas for high noise conditions, they were in the range of those in conventional tunnels