16 research outputs found
Influence of Alloying Elements and Solution Heat Treatment on Microstructure and Microhardness of the Ni-Nb-M System (M = Al, Ti, Cr, Fe)
Ni-based superalloys are widely used in critical components of aircraft engines and turbines and also in the petrochemical industry, for applications in highly corrosive environments. These alloys have as main characteristics their superior mechanical, corrosion and oxidation resistance at high temperatures, as well as creep resistance. The chemical composition associated with carrying out heat treatments directly influences the phases formed (such as the ordered cubic phase γ’-Ni3(Al,Ti) in the fcc γ-Ni matrix), and depending on the alloying elements and fraction, there is the possibility of an increase in mechanical strength. There is a certain gap in the literature regarding the study of ternary superalloys based on Ni-Nb, and the influence of the third alloying element on the microstructure and microhardness. In this context, the objective of the study is to characterize pseudo-eutectic alloys of the Ni-15Nb-xM and Ni-20Nb-xM systems (xM = 2Al, 4Ti, 15Fe and 15Cr, wt.%) and investigate the influence of alloy elements and solution heat treating on their microstructure and properties through X-Ray Diffraction, Optical Microscopy, Scanning Electron Microscopy and Vickers Microhardness. Microhardness and microstructures were significantly influenced by the addition of alloying elements. The addition of Cr had a significant effect on the hardness of the cast samples. All alloys showed microhardness and microstructural changes after solution heat treatment
Laser Cladding of Fe-based Metallic Glass/MoS2 Self-lubricating Composites: Effect of Power and Scanning Speed
Mechanical Properties and the Microstructure of β Ti-35Nb-10Ta-xFe Alloys Obtained by Powder Metallurgy for Biomedical Applications
Titanium alloys with high refractory metals content are required to obtain advanced biomaterials with a low elastic modulus and good mechanical properties. This work studies the influence of Fe content on the microstructure and mechanical properties of powder metallurgy Ti35Nb10Ta(Fe) alloys, with Fe content additions of 1.5, 3.0 and 4.5 wt%. Samples are obtained by uniaxial compaction and sintering at 1250 °C and 1300 °C. Microstructural characterization is performed by scanning and transmission electron microscopy and mechanical characterization by bending, compression and a hardness test. The elastic modulus is measured by the ultrasounds technique. The results show a 10% increase in the maximum bending strength with an increase in the sintering temperature. The obtained microstructure is composed of β-Ti phase (bcc) and some regions where laths of the α-Ti (hcp) phase occur along the grain boundaries. Fe addition slightly improves the stability of the β-Ti phase and conversely decreases the maximum strength and final deformability due to increased porosity. The Ti35Nb10Ta alloy composition displays better properties, with an elastic modulus of 75 GPa, a bending strength of 853 MPa and compression strength of 1000 MPa
On the process-related rivet microstructural evolution, material flow and mechanical properties of Ti-6Al-4V/GFRP friction-riveted joints
In the current work, process-related thermo-mechanical changes in the rivet microstructure, joint local and global mechanical properties, and their correlation with the rivet plastic deformation regime were investigated for Ti-6Al-4V (rivet) and glass-fiber-reinforced polyester (GF-P) friction-riveted joints of a single polymeric base plate. Joints displaying similar quasi-static mechanical performance to conventional bolted joints were selected for detailed characterization. The mechanical performance was assessed on lap shear specimens, whereby the friction-riveted joints were connected with AA2198 gussets. Two levels of energy input were used, resulting in process temperatures varying from 460 ± 130 °C to 758 ± 56 °C and fast cooling rates (178 ± 15 °C/s, 59 ± 15 °C/s). A complex final microstructure was identified in the rivet. Whereas equiaxial α-grains with β-phase precipitated in their grain boundaries were identified in the rivet heat-affected zone, refined α' martensite, Widmanstätten structures and β-fleck domains were present in the plastically deformed rivet volume. The transition from equiaxed to acicular structures resulted in an increase of up to 24% in microhardness in comparison to the base material. A study on the rivet material flow through microtexture of the α-Ti phase and β-fleck orientation revealed a strong effect of shear stress and forging which induced simple shear deformation. By combining advanced microstructural analysis techniques with local mechanical testing and temperature measurement, the nature of the complex rivet plastic deformational regime could be determined.Helmholtz Associatio
Processing, as-cast microstructure and wear characteristics of a monotectic Al-Bi-Cu Alloy
Ternary Al-based monotectic alloys have a good combination of wear resistance and mechanical strength. While self-lubricating soft elements guarantee an adequate wear resistance, the modification with third elements can increase the ability to support load. In the present investigation, a collection of microstructures is generated through transient directional solidification of the Al-3.2wt.%Bi-3.0wt.%Cu alloy. Samples with different Bi spacing have been subjected to micro-adhesive wear ball tests. A relationship linking the wear volume, V, the microstructural spacing and the test time is proposed for Bi spacing higher than 16m, according to which V decreases with the decrease in Bi spacing. It is observed that wider and deeper grooves emerged on the surface of the samples related to more refined Bi and Al2Cu phases, that is, associated with Bi spacing and Bi diameter lower than 16 and 2.4m, respectively. A reverse trend is noted for these finer microstructures, for which V increases with further decrease in Bi spacing. This can be caused by the detachment of the very fine and less cohesive Al2Cu lamellas as the Al2O3 oxide breaks up forming debris, with the presence of these lamellas as loose debris at the interface acting as third-body abrasives28212011212CNPQ - Conselho Nacional de Desenvolvimento Científico e TecnológicoFAPESP – Fundação de Amparo à Pesquisa Do Estado De São Paulosem informação2017/12741-6The authors are grateful to FAPESP (São Paulo Research Foundation, Brazil: Grant 2017/12741-6) and CNPq- National Council for Scientific and Technological Development, for their financial suppor
Nonlinear optical properties of tungsten lead-pyrophosphate glasses containing metallic copper nanoparticles
We have prepared heavy metal oxide glasses containing metallic copper nanoparticles with promising nonlinear optical properties which were determined by Zscan and pump-probe measurements using femtosecond laser pulses. For the wavelengths within the plasmon band, we have observed saturable absorption and response times of 2.3 ps. For the other regions of the spectrum, reverse saturable absorption and lifetimes shorter than 200 fs were verified. The nonlinear refractive index is about 2.0×'10 POT. -19' m2/W from visible to telecom region, thus presenting an enhancement effect at wavelengths near the plasmon and Cu+2 d-d band.FAPESPCAPESCNP