31,996 research outputs found
Fracture toughness of SiC/Al metal matrix composite
An experimental study was conducted to evaluate fracture toughness of SiC/Al metal matrix composite (MMC). The material was a 12.7 mm thick extrusion of 6061-T6 aluminum alloy with 40 v/o SiC particulates. Specimen configuration and test procedure conformed to ASTM E399 Standard for compact specimens. It was found that special procedures were necessary to obtain fatigue cracks of controlled lengths in the preparation of precracked specimens for the MMC material. Fatigue loading with both minimum and maximum loads in compression was used to start the precrack. The initial precracking would stop by self-arrest. Afterwards, the precrack could be safely extended to the desired length by additional cyclic tensile loading. Test results met practically all the E399 criteria for the calculation of plane strain fracture toughness of the material. A valid K sub IC value of the SiC/Al composite was established as K sub IC = 8.9 MPa square root of m. The threshold stress intensity under which crack would cease to grow in the material was estimated as delta K sub th = 2MPa square root of m for R = 0.09 using the fatigue precracking data. Fractographic examinations show that failure occurred by the micromechanism involved with plastic deformation although the specimens broke by brittle fracture. The effect of precracking by cyclic loading in compression on fracture toughness is included in the discussion
Magnification relations of quad lenses and applications on Einstein crosses
In this work, we mainly study the magnification relations of quad lens models
for cusp, fold and cross configurations. By dividing and ray-tracing in
different image regions, we numerically derive the positions and magnifications
of the four images for a point source lying inside of the astroid caustic.
Then, based on the magnifications, we calculate the signed cusp and fold
relations for the singular isothermal elliptical lenses. The signed fold
relation map has positive and negative regions, and the positive region is
usually larger than the negative region as has been confirmed before. It can
also explain that for many observed fold image pairs, the fluxes of the Fermat
minimum images are apt to be larger than those of the saddle images. We define
a new quantity cross relation which describes the magnification discrepancy
between two minimum images and two saddle images. Distance ratio is also
defined as the ratio of the distance of two saddle images to that of two
minimum images. We calculate the cross relations and distance ratios for nine
observed Einstein crosses. In theory, for most of the quad lens models, the
cross relations decrease as the distance ratios increase. In observation, the
cross relations of the nine samples do not agree with the quad lens models very
well, nevertheless, the cross relations of the nine samples do not give obvious
evidence for anomalous flux ratio as the cusp and fold types do. Then, we
discuss several reasons for the disagreement, and expect good consistencies for
more precise observations and better lens models in the future.Comment: 12 pages, 11 figures, accepted for publication in MNRA
Assessment of probability of detection of delaminations in fiber-reinforced composites
Delamination is one of the critical defects in composite materials and structures. An ultrasonic C-scan imaging technique which maps out the acoustic impedance mismatched areas with respect to the sample coordinates, is particularly well suited for detecting and characterizing delaminations in composites. To properly interpret the results, it is necessary to correlate the indications with the detection limits and probability of detection (POD) of the ultrasonic C-scan imaging technique. The baseline information on the assessment of POD of delaminations in composite materials and structures is very beneficial to the evaluation of spacecraft materials. In this study, we review the principle of POD, describe the laboratory set-up and procedure, and present the experimental results as well as assessment of POD of delaminations in fiber reinforced composite panels using ultrasonic C-scan techniques
Low Temperature Creep of a Titanium Alloy Ti-6Al-2Cb-1Ta-0.8Mo
This paper presents a methodology for the analysis of low temperature creep of titanium alloys in order to establish design limitations due to the effect of creep. The creep data on a titanium Ti-6Al-2Cb-1Ta-0.8Mo are used in the analysis. A creep equation is formulated to determine the allowable stresses so that creep at ambient temperatures can be kept within an acceptable limit during the service life of engineering structures or instruments. Microcreep which is important to design of precision instruments is included in the discussion also
Structure of CdTe/ZnTe superlattices
The structure of CdTe/ZnTe superlattices has been analyzed through θ/2θ x‐ray diffraction, photoluminescence, and in situ reflection high‐energy electron diffraction (RHEED) measurements. Samples are found to break away from Cd_(x)Zn_(1−x)Te buffer layers as a consequence of the 6% lattice mismatch in this system. However, defect densities in these superlattices are seen to drop dramatically away from the buffer layer interface, accounting for the intense photoluminescence and high‐average strain fields seen in each of our samples. Observed variations in residual strains suggest that growth conditions play a role in forming misfit defects. This could explain discrepancies with calculated values of critical thickness based on models which neglect growth conditions. Photoluminescence spectra reveal that layer‐to‐layer growth proceeded with single monolayer uniformity, suggesting highly reproducible growth. Our results give hope for relatively defect‐free Cd_(x)Zn_(1−x)Te/Cd_(y)Zn_(1−y)Te superlattices with the potential for applications to optoelectronics offered by intense visible light emitters
- …