An Approach to Beneficiation of Apatite Ore of Purulia

West Bengal Mineral Development and Trading Corporation operates the apatite mine in Purulia District of West Bengal. The produce three grades of samples, i.e. (i) High grade above 30% P2O5 (ii) Average grade of about 20% P2O5 and (iii)Low grade of 12% P2O5. The average is directly marketed as fertiliser for application in tea garden etc. The medium or average grade sample is mined from areas around the main ore body and contains substantial amount of ferruginous material besides other gangue minerals. The low grade ore is dumped separately and occasionally blended with high grade of ore to prepare the average grade for direct marketing. Thus every bit of apatite from the mines is used except for the top soil. But with reduc-ed demand, the manufacturer is faced with a selling problem and reduced production. Value addition by way of making high grade product is one option to pursue with. The typical problem is of iron removal as presence of high iron hinders value addition in terms of phosphate during down stream operation. Studies on the average grade sample indicated that using suitable processing steps the phos-phate content could be increased to +38% P205 with very low content of iron & silica. The present paper deals approach adopted in beneficiating the average grade apatite ore of Purulia. Key Words: apatite, Purulia, iron, magnetic separation, flotation

Minerological aspects of lead sintering

A brief overview on lead sinter microstructure is presented. Characteristic micro-structural features of a good and bad sinter are highlighted and these are used in a case study involving use of a low grade and complex concentrate of lead (-40% Pb) in the sintering operation. The plant sinter produced exhibited low strength and its nticrostructural examination revealed non-uniform distribution of porosity along with unsintered galena and low melting lead silicate phase. Part replacement of limestone by lime helped in producing sinter with good physical properties and desirable microstructure. The sinter with modified feed chemistry had more uniform distribution of porosity and presence of primarily a Pb-Fe silicate phase characterised by a (Pb+Fe):Si mole ratio of 3:1. Ca-Pb-Zn-Fe-Al-silicate phase identified as hardysonite and a spine! phase of the type (Fe,Zn)O.(Fe,Al),OJ. Lead nietal/oxide/sulphide occurred in the sinter only rarely. The likely implications of lime addition to the sinter charge mix are discussed Key Words: Lead. Complex and low grade concentrate. Sintering. Process Mineralog

Sociobiological Control of Plasmid copy number

Background:
All known mechanisms and genes responsible for the regulation of plasmid replication lie with the plasmid rather than the chromosome. It is possible therefore that there can be copy-up mutants. Copy-up mutants will have within host selective advantage. This would eventually result into instability of bacteria-plasmid association. In spite of this possibility low copy number plasmids appear to exist stably in host populations. We examined this paradox using a computer simulation model.

Model:
Our multilevel selection model assumes a wild type with tightly regulated replication to ensure low copy number. A mutant with slightly relaxed replication regulation can act as a “cheater” or “selfish” plasmid and can enjoy a greater within-host-fitness. However the host of a cheater plasmid has to pay a greater cost. As a result, in host level competition, host cell with low copy number plasmid has a greater fitness. Furthermore, another mutant that has lost the genes required for conjugation was introduced in the model. The non-conjugal mutant was assumed to undergo conjugal transfer in the presence of another conjugal plasmid in the host cell.

Results:
The simulatons showed that if the cost of carrying a plasmid was low, the copy-up mutant could drive the wild type to extinction or very low frequencies. Consequently, another mutant with a higher copy number could invade the first invader. This process could result into an increasing copy number. However above a certain copy number within-host selection was overcompensated by host level selection leading to a rock-paper-scissor (RPS) like situation. The RPS situation allowed the coexistence of high and low copy number plasmids. The non-conjugal “hypercheaters” could further arrest the copy numbers to a substantially lower level.

Conclusions:
These sociobiological interactions might explain the stability of copy numbers better than molecular mechanisms of replication regulation alone

Studies on Medium Grade Ilmenite-Depleted Beach Placer deposit of Chavakkad Ponnani Coast, Kerala

In the present paper, characterization, beneficiation and further value addition studies carried out with samples collected from unexploited Chavakkad ponnani (CP) area of Kerala coast have been reported. Characterization studies involve size and chemical analyses, sink and float studies and optical microscopy. total 21 samples were collected from 18 km. stretch of CP area at almost 1 km. apart. While sink and float studies and optical microscopy were carried on with all individual samples, detail characterization and beneficiation studies were undertaken with composite samples-one prepared from all 21 samples and the second from few selected samples. Pre-concentration followed by high tension separation and magnetic separation yielded product containing more than 95% THM with around 90% recovery. Further value addition studies with generated ilmenite concentrate was found to produce synthetic rutile, through reduction followed by oxidation and leaching, containing more than 94% TiO2

Wettability characteristics of an Al2O3/SiO2-based ceramic modified with CO2, Nd:YAG, excimer and high-power diode lasers

Interaction of CO2, Nd:YAG, excimer and high power diode laser (HPDL) radiation with the surface of an Al2O3/SiO2 based ceramic was found to effect significant changes in the wettability characteristics of the material. It was observed that interaction with CO2, Nd:YAG and HPDL radiation reduced the enamel contact angle from 1180 to 310, 340 and 330 respectively. In contrast, interaction with excimer laser radiation resulted an increase in the contact angle to 1210. Such changes were identified as being due to: (i) the melting and partial vitrification of the Al2O3/SiO2 based ceramic surface as a result of interaction with CO2, Nd:YAG HPDL radiation. (ii) the surface roughness of the Al2O3/SiO2 based ceramic increasing after interaction with excimer laser radiation. (iii) the surface oxygen content of the Al2O3/SiO2 based ceramic increasing after interaction with CO2, Nd:YAG and HPDL radiation. The work has shown that the wettability characteristics of the Al2O3/SiO2 based ceramic could be controlled and/or modified with laser surface treatment. In particular, whether the laser radiation had the propensity to cause surface melting. However, a wavelength dependance of the change of the wetting properties could not be deduced from the findings of this work

Melatonin Induces Follicle Maturation in Danio rerio

Most organisms modulate their reproductive activity responding to day length by the nocturnal release of melatonin by the pineal gland. This hormone is also responsible for synchronizing reproduction with specific external environment stimuli in order to optimize reproductive success

The effects of cold working on sensitization and intergranular corrosion behavior of AISI 304 stainless steel

The effects of prior cold rolling of up to an 80 pct reduction in thickness on the sensitization-desensitization behavior of Type AISI 304 stainless steel and its susceptibility to intergranular corrosion have been studied by electrochemical potentiokinetic reactivation (EPR) and Strauss-test methods. The results indicate that the prior deformation accelerated the sensitization as compared to the undeformed stainless steel. The deformed Type 304 stainless steel experienced desensitization at higher temperatures and times, and it was found to be enhanced by increased cold deformation. This could be attributed to the increased long-range chromium diffusion, possibly brought on by increasing pipe diffusion and vacancies. The role of the deformation-induced martensite (DIM) and texture, introduced by uniaxial cold rolling, on the sensitization-desensitization kinetics has also been discussed. This study could not reveal any systematic relationship between texture and the degree of sensitization (DOS) obtained. The effect of DIM on DOS seems to be pronounced at 500 °C when the steel retained significant amounts of DIM; however, the retained DIM is insignificant at higher sensitization times and temperatures