Electrical Cable Design for Urban Air Mobility Aircraft

Urban Air Mobility (UAM) describes a new type of aviation focused on efficient flight within urban areas for moving people and goods. There are many different configurations of UAM vehicles, but they generally use an electric motor driving a propeller or ducted fan powered by batteries or a hybrid electric power generation system. Transmission cables are used to move energy from the storage or generation system to the electric motors. Though terrestrial power transmission cables are well established technology, aviation applications bring a whole host of new design challenges that are not typical considerations in terrestrial applications. Aircraft power transmission cable designs must compromise between resistance-per-length, weight-per-length, volume constraints, and other essential qualities. In this paper we use a multidisciplinary design optimization to explore the sensitivity of these qualities to a representative tiltwing turboelectric UAM aircraft concept. This is performed by coupling propulsion and thermal models for a given mission criteria. Results presented indicate that decreasing cable weight at the expense of increasing cable volume or cooling demand is effective at minimizing maximum takeoff weight (MTO). These findings indicate that subsystem designers should update their modeling approach in order to contribute to system-level optimality for highly-coupled novel aircraft. Mobility (UAM) vehicles have the potential to change urban and intra-urban transport in new and interesting ways. In a series of two papers Johnson et al.1 and Silva et al.2 presented four reference vehicle configurations that could service different niches in the UAM aviation category. Of those, this paper focuses on the Vertical Take-off and Landing (VTOL) tiltwing configuration shown in Figure 1. This configuration uses a turboelectric power system, feeding power from a turbo-generator through a system of transmission cables to four motors spinning large propellers on the wings. Previous work on electric cable subsystems leaves much yet to be explored, especially in the realm of subsystem coupling. Several aircraft optimization studies1, 3, 4 only considered aircraft electrical cable weight and ignored thermal effects. Electric and hybrid-electric aircraft studies by Mueller et al.5 and Hoelzen et al.6 selected a cable material but did not investigate alternative materials. Advanced cable materials have been examined by a number of authors: Alvarenga7 examined carbon nanotube (CNT) conductors for low-power applications. De Groh8, 9 examined CNT conductors for motor winding applications. Behabtu et al.,10 and Zhao et al.11 examined CNT conductors for a general applications. There were some studies that examined the thermal effects of cables but they did not allow the cable material to change; El-Kady12 optimized ground-cable insulation and cooling subject constraints. Vratny13 selected cable material based on vehicle power demand, and required resulting cable heat to be dissipated by the Thermal Management System (TMS). None of these previous studies allowed for the selection of the cable material based on a system level optimization goal. Instead, they focused on sub-system optimality such as minimum weight, which comes at the expense of incurring additional costs for other subsystems. Dama14 selected overhead transmission line materials using a weighting function and thermal constraints. However, that work was not coupled with any aircraft subsystems like a TMS. The traditional aircraft design approach, which relies on assembling groups of optimal subsystems, breaks down when considering novel aircraft concepts like the tiltwing vehicle. In a large part, this is because novel concepts have a much higher degree of interaction or coupling between subsystems. For example, when a cable creates heat, this heat needs to be dissipated by the TMS, which needs power supplied by the turbine, and delivering the power creates more heat. The cable, the TMS, and the turbine are all coupled. A change to one subsystem will affect all the other subsystems, much to the consternation of subsystem design experts. Multidisciplinary optimization is the design approach that can address these challenges. However, to fully take advantage of this, we must change the way we think about subsystem design. Specifically, we must move away from point design, and focus on creating solution spaces. The work presented in this paper uses the multidisciplinary optimization approach with aircraft level models to study the system-level sensitivity of cable traits: weight-per-length and resistance-per-length. Additionally, we examined the effects of vehicle imposed volume constraints on these traits. This is useful for three purposes: (1) to demonstrate a framework that can perform a coupled analysis between the aircraft thermal and propulsion systems, (2) to provide a method by which future cable designs can be evaluated against each other given a system-level design goal, (3) to provide insight into what cable properties may be promising for future research. This last element is explored given the caveat that the models contained in this analysis do not represent high-fidelity systems. Thus, while we can demonstrate coupling in between systems, the exact system-level sensitivity to a given parameter may change if a subsystem model or the assumptions governing that model change. The organization of this paper is as follows, in Sec II we outline a method to combine the VTOL vehicle design and cable information in order to produce cables sensitivity studies. Results analysis and discussion are contained in Sec III. Conclusions are presented in Sec IV

Load Flow Analysis with Analytic Derivatives for Electric Aircraft Design Optimization

Many of the aircraft concepts of the future are exploring the use of hybrid-, turbo- or all-electric propulsion systems to improve performance and decrease environmental impacts. These aircraft concepts range from small rotorcraft for urban air mobility to conventional commercial transports to large blended wing body designs. Developing the conceptual design for these vehicles presents a challenge, however, as traditional aircraft design tools often were not developed to handle these unique propulsion system architectures. Previous studies on these vehicles have therefore relied on relatively simple models of the electrical transmission and distribution system. This paper presents the development of a hybrid AC-DC load flow (or power flow) analysis capability to enhance the conceptual design of these concept vehicles. Specifically, the desire was to create a load flow analysis capability within the OpenMDAO framework that is also being used to develop a set of compatible tools for rapid optimization of conceptual designs. This load flow analysis capability is unique in its flexible object-oriented structure and implementation of analytic derivatives to facilitate the use of solvers and gradient based optimization in the design process. The developed hybrid load flow analysis capability is first verified against a published 13-bus example then used to model the electrical distribution system for a turbo-electric tiltwing aircraft

Widespread and persistent invasions of terrestrial habitats coincident with larval feeding behavior transitions during snail-killing fly evolution (Diptera: Sciomyzidae)

BACKGROUND: Transitions in habitats and feeding behaviors were fundamental to the diversification of life on Earth. There is ongoing debate regarding the typical directionality of transitions between aquatic and terrestrial habitats and the mechanisms responsible for the preponderance of terrestrial to aquatic transitions. Snail-killing flies (Diptera: Sciomyzidae) represent an excellent model system to study such transitions because their larvae display a range of feeding behaviors, being predators, parasitoids or saprophages of a variety of mollusks in freshwater, shoreline and dry terrestrial habitats. The remarkable genus Tetanocera (Tetanocerini) occupies five larval feeding groups and all of the habitat types mentioned above. This study has four principal objectives: (i) construct a robust estimate of phylogeny for Tetanocera and Tetanocerini, (ii) estimate the evolutionary transitions in larval feeding behaviors and habitats, (iii) test the monophyly of feeding groups and (iv) identify mechanisms underlying sciomyzid habitat and feeding behavior evolution. RESULTS: Bayesian inference and maximum likelihood analyses of molecular data provided strong support that the Sciomyzini, Tetanocerini and Tetanocera are monophyletic. However, the monophyly of many behavioral groupings was rejected via phylogenetic constraint analyses. We determined that (i) the ancestral sciomyzid lineage was terrestrial, (ii) there was a single terrestrial to aquatic habitat transition early in the evolution of the Tetanocerini and (iii) there were at least 10 independent aquatic to terrestrial habitat transitions and at least 15 feeding behavior transitions during tetanocerine phylogenesis. The ancestor of Tetanocera was aquatic with five lineages making independent transitions to terrestrial habitats and seven making independent transitions in feeding behaviors. CONCLUSIONS: The preponderance of aquatic to terrestrial transitions in sciomyzids goes against the trend generally observed across eukaryotes. Damp shoreline habitats are likely transitional where larvae can change habitat but still have similar prey available. Transitioning from aquatic to terrestrial habitats is likely easier than the reverse for sciomyzids because morphological characters associated with air-breathing while under the water\u27s surface are lost rather than gained, and sciomyzids originated and diversified during a general drying period in Earth\u27s history. Our results imply that any animal lineage having aquatic and terrestrial members, respiring the same way in both habitats and having the same type of food available in both habitats could show a similar pattern of multiple independent habitat transitions coincident with changes in behavioral and morphological traits

Comparison of 3-Factor Prothrombin Complex Concentrate and Low-Dose Recombinant Factor VIIa for Warfarin Reversal

INTRODUCTION: Prothrombin complex concentrate (PCC) and recombinant Factor VIIa (rFVIIa) have been used for emergent reversal of warfarin anticoagulation. Few clinical studies have compared these agents in warfarin reversal. We compared warfarin reversal in patients who received either 3 factor PCC (PCC3) or low-dose rFVIIa (LDrFVIIa) for reversal of warfarin anticoagulation. METHODS: Data were collected from medical charts of patients who received at least one dose of PCC3 (20 units/kg) or LDrFVIIa (1000 or 1200 mcg) for emergent warfarin reversal from August 2007 to October 2011. The primary end-points were achievement of an INR 1.5 or less for efficacy and thromboembolic events for safety. RESULTS: Seventy-four PCC3 and 32 LDrFVIIa patients were analyzed. Baseline demographics, reason for warfarin reversal, and initial INR were equivalent. There was no difference in the use of vitamin K or fresh frozen plasma. More LDrFVIIa patients achieved an INR of 1.5 or less (71.9% vs. 33.8%, p =0.001). The follow-up INR was lower after LDrFVIIa (1.25 vs. 1.75, p < 0.05) and the percent change in INR was larger after LDrFVIIa (54.1% vs. 38.8%, p = 0.002). There was no difference in the number of thromboembolic events (2 LDrFVIIa vs. 5 PCC3, p = 1.00), mortality, length of hospital stay, or cost. CONCLUSIONS: Based on achieving a goal INR of 1.5 or less, LDrFVIIa was more likely than PCC3 to reverse warfarin anticoagulation. Thromboembolic events were equivalent in patients receiving PCC3 and LDrFVIIa

No effect of repeated post-resistance exercise cold or hot water immersion on in-season body composition and performance responses in academy rugby players : A randomised controlled cross-over design

Purpose Following resistance exercise, uncertainty exists as to whether the regular application of cold water immersion attenuates lean muscle mass increases in athletes. The effects of repeated post-resistance exercise cold versus hot water immersion on body composition and neuromuscular jump performance responses in athletes were investigated. Methods Male, academy Super Rugby players (n = 18, 19.9 ± 1.5 y, 1.85 ± 0.06 m, 98.3 ± 10.7 kg) participated in a 12-week (4-week × 3-intervention, i.e., control [CON], cold [CWI] or hot [HWI] water immersion) resistance exercise programme, utilising a randomised cross-over pre–post-design. Body composition measures were collected using dual-energy X-ray absorptiometry prior to commencement and every fourth week thereafter. Neuromuscular squat (SJ) and counter-movement jump (CMJ) performance were measured weekly. Linear mixed-effects models were used to analyse main (treatment, time) and interaction effects. Results There were no changes in lean (p = 0.960) nor fat mass (p = 0.801) between interventions. CON (p = 0.004) and CWI (p = 0.003) increased (g = 0.08–0.19) SJ height, compared to HWI. There were no changes in CMJ height (p = 0.482) between interventions. Conclusion Repeated post-resistance exercise whole-body CWI or HWI does not attenuate (nor promote) increases in lean muscle mass in athletes. Post-resistance exercise CON or CWI results in trivial increases in SJ height, compared to HWI. During an in-season competition phase, our data support the continued use of post-resistance exercise whole-body CWI by athletes as a recovery strategy which does not attenuate body composition increases in lean muscle mass, while promoting trivial increases in neuromuscular concentric-only squat jump performance

No effect of repeated post-resistance exercise cold or hot water immersion on in-season body composition and performance responses in academy rugby players: A randomised controlled cross-over design

Purpose: Following resistance exercise, uncertainty exists as to whether the regular application of cold water immersion attenuates lean muscle mass increases in athletes. The effects of repeated post-resistance exercise cold versus hot water immersion on body composition and neuromuscular jump performance responses in athletes were investigated. Methods: Male, academy Super Rugby players (n = 18, 19.9 ± 1.5 y, 1.85 ± 0.06 m, 98.3 ± 10.7 kg) participated in a 12-week (4-week × 3-intervention, i.e., control [CON], cold [CWI] or hot [HWI] water immersion) resistance exercise programme, utilising a randomised cross-over pre–post-design. Body composition measures were collected using dual-energy X-ray absorptiometry prior to commencement and every fourth week thereafter. Neuromuscular squat (SJ) and counter-movement jump (CMJ) performance were measured weekly. Linear mixed-effects models were used to analyse main (treatment, time) and interaction effects. Results: There were no changes in lean (p = 0.960) nor fat mass (p = 0.801) between interventions. CON (p = 0.004) and CWI (p = 0.003) increased (g = 0.08–0.19) SJ height, compared to HWI. There were no changes in CMJ height (p = 0.482) between interventions. Conclusion: Repeated post-resistance exercise whole-body CWI or HWI does not attenuate (nor promote) increases in lean muscle mass in athletes. Post-resistance exercise CON or CWI results in trivial increases in SJ height, compared to HWI. During an in-season competition phase, our data support the continued use of post-resistance exercise whole-body CWI by athletes as a recovery strategy which does not attenuate body composition increases in lean muscle mass, while promoting trivial increases in neuromuscular concentric-only squat jump performance

The Structure of IR Luminous Galaxies at 100 Microns

We have observed twenty two galaxies at 100 microns with the Kuiper Airborne Observatory in order to determine the size of their FIR emitting regions. Most of these galaxies are luminous far-infrared sources, with L_FIR > 10^11 L_sun. This data constitutes the highest spatial resolution ever achieved on luminous galaxies in the far infrared. Our data includes direct measurements of the spatial structure of the sources, in which we look for departures from point source profiles. Additionally, comparison of our small beam 100 micron fluxes with the large beam IRAS fluxes shows how much flux falls beyond our detectors but within the IRAS beam. Several sources with point- like cores show evidence for such a net flux deficit. We clearly resolved six of these galaxies at 100 microns and have some evidence for extension in seven others. Those galaxies which we have resolved can have little of their 100 micron flux directly emitted by a point-like active galactic nucleus (AGN). Dust heated to ~40 K by recent bursts of non-nuclear star formation provides the best explanation for their extreme FIR luminosity. In a few cases, heating of an extended region by a compact central source is also a plausible option. Assuming the FIR emission we see is from dust, we also use the sizes we derive to find the dust temperatures and optical depths at 100 microns which we translate into an effective visual extinction through the galaxy. Our work shows that studies of the far infrared structure of luminous infrared galaxies is clearly within the capabilities of new generation far infrared instrumentation, such as SOFIA and SIRTF.Comment: 8 tables, 23 figure

Solution to the Perturbative Infrared Catastrophe of Hot Gauge Theories

The free energy of a nonabelian gauge theory at high temperature $T$ can be calculated to order $g^5$ using resummed perturbation theory, but the method breaks down at order $g^6$. A new method is developed for calculating the free energy to arbitrarily high accuracy in the high temperature limit. It involves the construction of a sequence of two effective field theories by first integrating out the momentum scale $T$ and then integrating out the momentum scale $g T$. The free energy decomposes into the sum of three terms, corresponding to the momentum scales $T$, $gT$, and $g^2T$. The first term can be calculated as a perturbation series in $g^2(T)$, where $g(T)$ is the running coupling constant. The second term in the free energy can be calculated as a perturbation series in $g(T)$, beginning at order $g^3$. The third term can also be expressed as a series in $g(T)$ beginning at order $g^6$, with coefficients that can be calculated using lattice simulations of 3-dimensional QCD. Leading logarithms of $T/(gT)$ and of $gT/(g^2T)$ can be summed up using renormalization group equations.Comment: 11 pages LaTeX, NUHEP-TH-94-2

ACR Appropriateness Criteria® Non-Spine Bone Metastases

Bone metastases are a common clinical problem, affecting many types of cancer patients. The presence of tumor in bone can cause significant morbidity including pain, neurological dysfunction, hypercalcemia, and pathological fracture leading to functional loss. The optimal treatment of a patient with bone metastases depends on many factors, including evaluation of the patient's goals of care, performance status, mechanical stability of the affected bone, life expectancy, and overall extent of disease. Treatment options may include radiotherapy, systemic therapies, surgical stabilization, medical pain management, and radiopharmaceuticals. Ideal management of bone metastases requires a coordinated multidisciplinary approach among diagnostic radiologists, radiation oncologists, medical oncologists, orthopedic surgeons, pain specialists, physiatrists, and palliative care specialists. The American College of Radiology Appropriateness Criteria? are evidence-based guidelines for specific clinical conditions that are reviewed every 3 years by a multidisciplinary expert panel. The guidelines development and review include an extensive analysis of current medical literature from peer-reviewed journals and the application of a well-established consensus methodology (modified Delphi) to rate the appropriateness of imaging and treatment procedures by the panel. In those instances where evidence is lacking or not definitive, expert opinion may be used to recommend imaging or treatment.Peer Reviewedhttps://deepblue.lib.umich.edu/bitstream/2027.42/140118/1/jpm.2014.9395.pd