68 research outputs found
Deadfall Syncline coal, quality and reserves
PRESENT INVESTIGATION
The purpose of the 1991 drilling program was twofold: 1. To evaluate the coal reserves in a previously identified thick coal in an area of low structural dips and dip-slope topography near the axial plunge of the west extension of the Deadfall Syncline, primarily for surface mining, and to determine the feasibility of mining additional beds in conjunction with the thick coal. (For the purposes of this investigation, this coal is designated K3 as explained below), 2. To examine a continuous and unbroken stratigraphic interval of the Corwin formation in the northeastern part of the Deadfall Syncline as an initial step toward evaluation of the whole basin. This was accomplished by drilling overlapping
holes aligned generally parallel to the dip direction, and spaced in accordance with
the magnitude of dip and depth capacity of the drill. About 720 feet of stratigraphic
section were covered in this way. A total of fourteen exploratory holes were drilled, ranging from 116 to 426 feet in depth (Figure
2). The drill was a Mobil B-60 mounted on a Nodwell tracked vehicle. Circulation was provided by a large compressor mounted on another Nodwell. Most of the footage was drilled with an air hammer, which provided a significant improvement in drilling rates over conventional rotary drilling. Lithology of cuttings from all holes was logged continuously, and composite grab samples from each 5 or 10 foot interval were taken. Coal cuttings were collected on a (relatively) clean plastic sheet, and promptly double bagged in plastic to minimize loss of bed moisture. Cores
were taken from the K3 coal at 3 drill hole locations, and the underlying K4 coal was also cored at one of these 3 holes. A comparison of core length to geophysical logs indicates essentially 100%
recovery for all cores. All samples, including rock cuttings, were shipped to the Mineral Industry Research Laboratory (MIRL), University of Alaska Fairbanks, for analyses and/or storage. All holes were logged with a Gearhart-Owen GeoLogger using natural garmna and gammagamma density tools. The log response with these tools for coals is distinct and unambiguous, particularly that of the density log, and the resolution is sufficient to estimate bed thickness to
within 3 to 4 inches (Figures 8 and 9)
Recommended from our members
Protein Shedding and ELF Magnetic Fields: Antibody Binding at the CD3 and CD20 Receptor Sites of Human Lymphocytes
Selecting fines recycle methods to optimize fluid bed combustor performance
Testing and analysis of a number of different fines recycle methods for fluid bed combustors has led to a generalized modeling technique. This model accounts for the effect of pertinent variables in determining overall combustion efficiencies. Computer application of this model has allowed trade-off studies to be performed that show the overall process effects of changes in individual operating parameters. Verification of the model has been accomplished in processing campaigns while combusting fuels such as graphite and bituminous coal. A 0.4 MW test unit was used for the graphite experimental work. Solid fuel was typically crushed to 5 mm maximum screen size. Bed temperatures were normally controlled at 900/sup 0/C; the combustor was an atmospheric unit with maximum in-bed pressures of 0.2 atm. Expanded bed depths ranged from 1.5 to 3 meters. Additional data was taken from recycle tests sponsored by EPRI on the B and W 6 ft x 6 ft fluid bed combustor. These tests used high sulfur coal in a 1.2 meter deep, 850/sup 0/C atmospheric fluidized bed of limestone, with low recycle rates and temperatures. Close agreement between the model and test data has been noted, with combustion efficiency predictions matching experimental results within 1%
Recommended from our members
Intracellular Calcium, Calcium Transport, and c-MYC mRNA Induction in Lymphocytes Exposed to 60 HZ Magnetic Fields: The Cell Membrane and the Signal Transduction Pathway
Recommended from our members
Comparison of calculations and in situ results for a large, heated test room at the Waste Isolation Pilot Plant (WIPP)
The mission of the Waste Isolation Pilot Plant (WIPP) Project is to develop the technology for safe disposal of the radioactive Transuranic (TRU) waste forms generated by the US defense programs. The WIPP facility has been constructed in the bedded salt deposits of Southeastern New Mexico. In the existing regulatory context, the requirement is to assure that the potential repository isolates the radioactive waste from the accessible environment and mankind. This requirement means, in part, that the creep closure and waste encapsulation of the salt must be predicted far into the future, a capability which requires a significant development of predictive technology. A series of large scale in situ experiments were fielded at the WIPP specifically to provide a data base for validation of the independently developed prediction technology. In this paper, we present the results of one large scale, heated test as analyzed according to the most advanced predictive capability. The closure measurements from a large scale, heated, in situ experimental room in salt are compared to numerical calculations using the most recent predictive technology, with very good agreement, limited potentially only by the unmodeled roof fracture and separation. 9 refs., 6 figs., 1 tab
Recommended from our members
Nuclear medicine program progress report for quarter ending December 31, 1991
This report presents information on (1) a new improved synthesis of carrier-free rhenium-188-labeled Re(V) dimercaptosuccinic acid (DMSA) complex as a potential therapeutic agent for treatment of thyroid medullary carcinoma; and (2) the synthesis and evaluation of a series of iodine-125-labeled analogues of altanserine for imaging of serotonin receptors
- …