Application of dynamical systems theory to the high angle of attack dynamics of the F-14

Dynamical systems theory has been used to study the nonlinear dynamics of the F-14. An eight degree of freedom model that does not include the control system present in operational F-14's has been analyzed. The aerodynamic model, supplied by NASA, includes nonlinearities as functions of the angles of attack and sideslip, the rotation rate, and the elevator deflection. A continuation method has been used to calculate the steady states of the F-14 as continuous functions of the control surface deflections. Bifurcations of these steady states have been used to predict the onset of wing rock, spiral divergence, and jump phenomena which cause the aircraft to enter a spin. A simple feedback control system was designed to eliminate the wing rock and spiral divergence instabilities. The predictions were verified with numerical simulations

Modeling for Active Control of Combustion and Thermally Driven Oscillations

Organized oscillations excited and sustained by high densities of energy release in combustion chambers have long caused serious problems in development of propulsion systems. The amplitudes often become sufficiently large to cause unacceptable structural vibrations. Because the oscillations are self-excited, they reach limiting amplitudes (limit cycles) only because of the action of nonlinear processes. Traditionally, satisfactory behavior has been achieved through a combination of trial-and-error design and testing, with control always involving passive means: geometrical modifications, changes of propellant composition, or devices to enhance dissipation of acoustic energy. Active control has been applied only to small-scale laboratory devices, but the limited success suggests the possibility of serious applications to full-scale propulsion systems. Realization of that potential rests on further experimental work, combined with deeper understanding of the mechanisms causing the oscillations and of the physical behavior of the systems. Effective design of active control systems will require faithful modeling of the relevant processes over broad frequency ranges covering the spectra of natural modes. This paper will cover the general character of the linear and nonlinear behavior of combustion systems, with special attention to acoustics and the mechanisms of excitation. The discussion is intended to supplement the paper by Doyle et al. concerned primarily with controls issues and the observed behavior of simple laboratory devices

Application of Bifurcation Theory to the High-Angle-of-Attack Dynamics of the F-14

Bifurcation theory has been used to study Ihe nonlinear dynamics of the F-14. An 8 degree-of-freedom model that does not include the control system present in operational F-14's has been analyzed. The aerodynamic model, supplied by NASA, includes nonlinearlties as functions of the angles of attack and sideslip, the rotation rate about the velocity vector, and the elevator deflection. A continuation method has been used to calculate the steady states of the F -14 as continuous functions of the elevator deflection. Bifurcations of these steady states have been used to predict the onset of wing rock, spiral divergence, and jump phenomena that cause the aircraft to enter a spin. A simple feedback control system was designed to eliminate the wing rock and spiral divergence instabilities. The predictions were verified with numerical simulations

Application of dynamical systems theory to nonlinear aircraft dynamics

Dynamical systems theory has been used to study nonlinear aircraft dynamics. A six degree of freedom model that neglects gravity has been analyzed. The aerodynamical model, supplied by NASA, is for a generic swept wing fighter and includes nonlinearities as functions of the angle of attack. A continuation method was use to calculate the steady states of the aircraft, and bifurcations of these steady states, as functions of the control deflections. Bifurcations were used to predict jump phenomena and the onset of periodic motion for roll coupling instabilities and high angle of attack maneuvers. The predictions were verified with numerical simulations

Impact and Influence Factors of Additive Manufacturing on Product Lifecycle Costs

At first sight the direct costs of Additive Manufacturing (AM) seem too high in comparison to traditional manufacturing. Considering the whole lifecycle costs of parts changes the point of view. Due to the modification of the new production process and new supply chains during a parts lifecycle, producing companies can strongly benefit from AM. Therefore, a costing model for assessing lifecycle costs with regard to specific applications and branches has been developed. The costing model represents the advantages of AM monetary. For the evaluation of this model and the influence factors, different case studies have been performed including different approaches in part redesign. Deeper research is and will be carried out with respect to the AM building rates and the comparability of various AM machines, as these facts are hardly comparable for end users. This paper will present the methodology as well as the results of the case studies conducted over the whole product lifecycle.Mechanical Engineerin

Analyzing Product Lifecycle Costs for a Better Understanding of Cost Drivers in Additive Manufacturing

The costs of additive manufactured parts often seem too high in comparison to those of traditionally manufactured parts, as the information about major cost drivers, especially for additive manufactured metal parts, is weak. Therefore, a lifecycle analysis of additive manufactured parts is needed to understand and rate the cost drivers that act as the largest contributors to unit costs, and to provide a focus for future cost reduction activities for the Additive Manufacturing (AM) technology. A better understanding of the cost structure will help to compare the AM costs with the opportunity costs of the classical manufacturing technologies and will make it easier to justify the use of AM manufactured parts. This paper will present work in progress and methodology based on a sample investigated with business process analysis / simulation and activity based costing. In addition, cost drivers associated with metal AM process will be rated.Mechanical Engineerin

The merging/AGN connection: A case for 3D spectroscopy

We discuss an ongoing study of the connection between galaxy merging/interaction and AGN activity, based on integral field spectroscopy. We focus on the search for AGN ionization in the central regions of mergers, previously not classified as AGNs. We present here the science case, the current status of the project, and plans for future observations.Comment: 4 pages, 3 figure, Euro3D Science Workshop, Cambridge, May 2003, AN, accepte