Si photocathode with Ag-supported dendritic Cu catalyst for CO2 reduction

Si photocathodes integrated with Ag-supported dendritic Cu catalysts are used to perform light-driven reduction of CO2 to C2 and C3 products in aqueous solution. A back illumination geometry with an n-type Si absorber was used to permit the use of absorbing metallic catalysts. Selective carrier collection was accomplished by a p+ implantation on the illumination side and an n+ implantation followed by atomic layer deposition of TiO2 on the electrolyte site. The Ag-supported dendritic Cu CO2 reduction catalyst was formed by evaporation of Ag followed by high-rate electrodeposition of Cu to form a high surface area structure. Under simulated 1 sun illumination in 0.1 M CsHCO3 saturated with CO2, the photovoltage generated by the Si (∼600 mV) enables C2 and C3 products to be produced at -0.4 vs. RHE. Texturing of both sides of the Si increases the light-limited current density, due to reduced reflection on the illumination side, and also deceases the onset potential. Under simulated diurnal illumination conditions photocathodes maintain over 60% faradaic efficiency to hydrocarbon and oxygenate products (mainly ethylene, ethanol, propanol) for several days. After 10 days of testing, contamination from the counter electrode is observed, which causes an increase in hydrogen production. This effect is mitigated by a regeneration procedure which restores the original catalyst selectivity. A tandem, self-powered CO2 reduction device was formed by coupling a Si photocathode with two series-connected semitransparent CH3NH3PbI3 perovskite solar cells, achieving an efficiency for the conversion of sunlight to hydrocarbons and oxygenates of 1.5% (3.5% for all products)

Deterministic Assembly of Arrays of Lithographically Defined WS2 and MoS2 Monolayer Features Directly from Multilayer Sources into Van der Waals Heterostructures

One of the major challenges in the van der Waals (vdW) integration of two-dimensional (2D) materials is achieving high-yield and high-throughput assembly of predefined sequences of monolayers into heterostructure arrays. Mechanical exfoliation has recently been studied as a promising technique to transfer monolayers from a multilayer source synthesized by other techniques, allowing the deposition of a wide variety of 2D materials without exposing the target substrate to harsh synthesis conditions. Although a variety of processes have been developed to exfoliate the 2D materials mechanically from the source and place them deterministically onto a target substrate, they can typically transfer only either a wafer-scale blanket or one small flake at a time with uncontrolled size and shape. Here, we present a method to assemble arrays of lithographically defined monolayer WS2 and MoS2 features from multilayer sources and directly transfer them in a deterministic manner onto target substrates. This exfoliate-align-release process - without the need of an intermediate carrier substrate - is enabled by combining a patterned, gold-mediated exfoliation technique with a new optically transparent, heat-releasable adhesive. WS2/MoS2 vdW heterostructure arrays produced by this method show the expected interlayer exciton between the monolayers. Light-emitting devices using WS2 monolayers were also demonstrated, proving the functionality of the fabricated materials. Our work demonstrates a significant step toward developing mechanical exfoliation as a scalable dry transfer technique for the manufacturing of functional, atomically thin materials

Microwave Transport in Metallic Single-Walled Carbon Nanotubes

The dynamical conductance of electrically contacted single-walled carbon nanotubes is measured from dc to 10 GHz as a function of source-drain voltage in both the low-field and high-field limits. The ac conductance of the nanotube itself is found to be equal to the dc conductance over the frequency range studied for tubes in both the ballistic and diffusive limit. This clearly demonstrates that nanotubes can carry high-frequency currents at least as well as dc currents over a wide range of operating conditions. Although a detailed theoretical explanation is still lacking, we present a phenomenological model of the ac impedance of a carbon nanotube in the presence of scattering that is consistent with these results.Comment: Added reference

Quantitative Mid-infrared Photoluminescence Characterization of Black Phosphorus–Arsenic Alloys

Black phosphorus (bP) is a promising material for mid-infrared (mid-IR) optoelectronic applications, exhibiting high performance light emission and detection. Alloying bP with arsenic extends its operation toward longer wavelengths from 3.7 μm (bP) to 5 μm (bP3As7), which is of great practical interest. Quantitative optical characterizations are performed to establish black phosphorus-arsenic (bPAs) alloys optoelectronic quality. Anisotropic optical constants (refractive index, extinction coefficient, and absorption coefficient) of bPAs alloys from near-infrared to mid-IR (0.2-0.9 eV) are extracted with reflection measurements, which helps optical device design. Quantitative photoluminescence (PL) of bPAs alloys with different As concentrations are measured from room temperature to 77 K. PL quantum yield measurements reveal a 2 orders of magnitude decrease in radiative efficiency with increasing As concentration. An optical cavity is designed for bP3As7, which allows for up to an order of magnitude enhancement in the quantum yield due to the Purcell effect. Our comprehensive optical characterization provides the foundation for high performance mid-IR optical device design using bPAs alloys

Shape-controlled single-crystal growth of InP at low temperatures down to 220 °C.

III-V compound semiconductors are widely used for electronic and optoelectronic applications. However, interfacing III-Vs with other materials has been fundamentally limited by the high growth temperatures and lattice-match requirements of traditional deposition processes. Recently, we developed the templated liquid-phase (TLP) crystal growth method for enabling direct growth of shape-controlled single-crystal III-Vs on amorphous substrates. Although in theory, the lowest temperature for TLP growth is that of the melting point of the group III metal (e.g., 156.6 °C for indium), previous experiments required a minimum growth temperature of 500 °C, thus being incompatible with many application-specific substrates. Here, we demonstrate low-temperature TLP (LT-TLP) growth of single-crystalline InP patterns at substrate temperatures down to 220 °C by first activating the precursor, thus enabling the direct growth of InP even on low thermal budget substrates such as plastics and indium-tin-oxide (ITO)-coated glass. Importantly, the material exhibits high electron mobilities and good optoelectronic properties as demonstrated by the fabrication of high-performance transistors and light-emitting devices. Furthermore, this work may enable integration of III-Vs with silicon complementary metal-oxide-semiconductor (CMOS) processing for monolithic 3D integrated circuits and/or back-end electronics

Scaling analysis of Schottky barriers at metal-embedded semiconducting carbon nanotube interfaces

We present an atomistic self-consistent tight-binding study of the electronic and transport properties of metal-semiconducting carbon nanotube interfaces as a function of the nanotube channel length when the end of the nanotube wire is buried inside the electrodes. We show that the lineup of the nanotube band structure relative to the metal Fermi-level depends strongly on the metal work function but weakly on the details of the interface. We analyze the length-dependent transport characteristics, which predicts a transition from tunneling to thermally-activated transport with increasing nanotube channel length.Comment: To appear in Phys.Rev.B Rapid Communications. Color figures available in PRB online versio

Synthesis, Contact Printing, and Device Characterization of Ni-Catalyzed, Crystalline InAs Nanowires

InAs nanowires have been actively explored as the channel material for high performance transistors owing to their high electron mobility and ease of ohmic metal contact formation. The catalytic growth of non-epitaxial InAs nanowires, however, has often relied on the use of Au colloids which is non-CMOS compatible. Here, we demonstrate the successful synthesis of high yield of crystalline InAs nanowires with high yield and tunable diameters by using Ni nanoparticles as the catalyst material on amorphous SiO2 substrates. The nanowires show superb electrical properties with field-effect electron mobility ~2,700 cm2/Vs and ION/IOFF >103. The uniformity and purity of the grown InAs nanowires are further demonstrated by large-scale assembly of parallel arrays of nanowires on substrates via the contact printing process that enables high performance, printable transistors, capable of delivering 5-10 mA ON currents (~400 nanowires).Comment: 21 pages, 5 figures included, all in .docx format. Nano Research (In Press

High-Field, Quasi-Ballistic Transport in Short Carbon Nanotubes

Single walled carbon nanotubes with Pd ohmic contacts and lengths ranging from several microns down to 10 nm are investigated by electron transport experiments and theory. The mean free path (mfp) for acoustic phonon scattering is estimated to be lap~300 nm, and that for optical phonon scattering is lop~15 nm. Transport through very short (~10 nm) nanotubes is free of significant acoustic and optical phonon scattering and thus ballistic and quasi-ballistic at the low and high bias voltage limits respectively. High currents of up to 70 uA can flow through a short nanotube. Possible mechanisms for the eventual electrical breakdown of short nanotubes at high fields are discussed. The results presented here have important implications to high performance nanotube transistors and interconnects.Comment: 4 figures. PRL, in pres

Topological transitions in carbon nanotube networks via nanoscale confinement

Efforts aimed at large-scale integration of nanoelectronic devices that exploit the superior electronic and mechanical properties of single-walled carbon nanotubes (SWCNTs) remain limited by the difficulties associated with manipulation and packaging of individual SWNTs. Alternative approaches based on ultra-thin carbon nanotube networks (CNNs) have enjoyed success of late with the realization of several scalable device applications. However, precise control over the network electronic transport is challenging due to i) an often uncontrollable interplay between network coverage and its topology and ii) the inherent electrical heterogeneity of the constituent SWNTs. In this letter, we use template-assisted fluidic assembly of SWCNT networks to explore the effect of geometric confinement on the network topology. Heterogeneous SWCNT networks dip-coated onto sub-micron wide ultra-thin polymer channels exhibit a topology that becomes increasingly aligned with decreasing channel width and thickness. Experimental scale coarse-grained computations of interacting SWCNTs show that the effect is a reflection of an aligned topology that is no longer dependent on the network density, which in turn emerges as a robust knob that can induce semiconductor-to-metallic transitions in the network response. Our study demonstrates the effectiveness of directed assembly on channels with varying degrees of confinement as a simple tool to tailor the conductance of the otherwise heterogeneous network, opening up the possibility of robust large-scale CNN-based devices.Comment: 4 pages, 3 figure