16 research outputs found

    Structural variants of biodegradable polyesterurethane in vivo evoke a cellular and angiogenic response that is dictated by architecture

    Get PDF
    This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ 2008 Acta Materialia Inc.The aim of this study was to investigate an in vivo tissue response to a biodegradable polyesterurethane, specifically the cellular and angiogenic response evoked by varying implant architectures in a subcutaneous rabbit implant model. A synthetic biodegradable polyesterurethane was synthesized and processed into three different configurations: a non-porous film, a porous mesh and a porous membrane. Glutaraldehyde cross-linked bovine pericardium was used as a control. Sterile polyesterurethane and control samples were implanted subcutaneously in six rabbits (n = 12). The rabbits were killed at 21 and 63 days and the implant sites were sectioned and histologically stained using haemotoxylin and eosin (H&E), Masson’s trichrome, picosirius red and immunostain CD31. The tissue–implant interface thickness was measured from the H&E slides. Stereological techniques were used to quantify the tissue reaction at each time point that included volume fraction of inflammatory cells, fibroblasts, fibrocytes, collagen and the degree of vascularization. Stereological analysis inferred that porous scaffolds with regular topography are better tolerated in vivo compared to non-porous scaffolds, while increasing scaffold porosity promotes angiogenesis and cellular infiltration. The results suggest that this biodegradable polyesterurethane is better tolerated in vivo than the control and that structural variants of biodegradable polyesterurethane in vivo evoke a cellular and angiogenic response that is dictated by architecture.Irish Research Council for Science, Engineering and Technology: funded by the National Development Plan. Enterprise Ireland: Research Innovation Partnership

    Secured Hardware Design - an Overview

    Get PDF
    Security is a prime concern in the design of a wide variety of embedded systems and security processors. So the customer security devices such as smart cards and security processors are prone to attack and there are on going research to protect these devices from attackers who intend to extract key information from these devices. Also an active attacker can induce errors during computation and exploit the faulty result to extract the key information embedded in the processor. Due to the design time issues weakness in the design is often revealed in the manufactured chips. Also because the post- manufacture security evaluation is time consuming and expensive, these security issues have to be considered at the design phase. This paper outlines some of the hardware attacks and provides a general idea of the process of these attacks

    Zeta Potential of Modified Multi-walled Carbon Nanotubes in Presence of poly (vinyl alcohol) Hydrogel

    Get PDF
    The main objective of this study is investigate the behavior of the Zeta Potential of the MWCNT modified with SDS(Sodium Dodecyl Sulfate) and CTAB(Cetyl Tetraethyl Ammonium Bromide) in presence of PVA. Full hydrolyzed PVA was used. As a result, adding PVA in the CNT solution led to decrease the Zeta Potential. The Zeta Potential of suspended colloid varied from 42.00mV to 6.48mV and -45.00mV to -6.4mV at 1.5% concentration of PVA; according with the changing pH, the Zeta Potential dropped to near zero at pH 3 and 11. The pH and PVA has strong influence in the reduction of ZP of MWCNT solution. MWCNT-PVA solution with 33.30mV, -35.69mV at 0.01% of PVA was exposed under AC field; a uniform coat was obtained, with the SDS-MWCNT-PVA solution.National Natural Science Foundation of China Project (Grant No.51073024), the Royal Society-NSFC international joint project (Grant No.51111130207) and Beijing Municipal Science and Technology Plan Projects (No. Z111103066611005)

    Modeling of Substrate Noise Effects in Dynamic CMOS Circuits

    Get PDF
    The decrease in the feature size has led to the integration of both digital and analog circuits on the same silicon die which has led to many crosstalk issues. The crosstalk due to the substrate interactions also plagiarizes complete digital systems. This paper lays emphasis on this fact and because of the vulnerability of dynamic CMOS circuits to noise; a brief study of the effects of substrate variations on the performance of the dynamic CMOS circuits is carried out in this paper. The effects of substrate noise at very high frequencies (above 10 GHz) are also depicted in this paper. In order to accurately estimate the effects of substrate noise a substrate model is proposed and verified for functionality in the last section of this paper

    A clinically relevant in vivo model for the assessment of scaffold efficacy in abdominal wall reconstruction

    Get PDF
    Copyright © The Author(s) 2017. An animal model that allows for assessment of the degree of stretching or contraction of the implant area and the in vivo degradation properties of biological meshes is required to evaluate their performance in vivo. Adult New Zealand rabbits underwent full thickness subtotal unilateral rectus abdominis muscle excision and were reconstructed with the non-biodegradable Peri-Guard®, Prolene® or biodegradable Surgisis® meshes. Following 8 weeks of recovery, the anterior abdominal wall tissue samples were collected for measurement of the implant dimensions. The Peri-Guard and Prolene meshes showed a slight and obvious shrinkage, respectively, whereas the Surgisis mesh showed stretching, resulting in hernia formation. Surgisis meshes showed in vivo biodegradation and increased collagen formation. This surgical rabbit model for abdominal wall defects is advantageous for evaluating the in vivo behaviour of surgical meshes. Implant area stretching and shrinkage were detected corresponding to mesh properties, and histological analysis and stereological methods supported these findings.This study was financially supported by the Enterprise Ireland (Technology Development Grant). This publication has emanated from research conducted with the financial support of Science Foundation Ireland (SFI) and is co-funded under the European Regional Development Fund under grant no. 13/RC/2073. This study was also supported by the Centre for Microscopy & Imaging funded by NUI Galway and PRTLI, Cycles 4 and 5, National Development Plan 2007–2013

    Chemically roughened solid silver: A simple, robust and broadband SERS substrate

    Get PDF
    Surface-enhanced Raman spectroscopy (SERS) substrates manufactured using complex nano-patterning techniques have become the norm. However, their cost of manufacture makes them unaffordable to incorporate into most biosensors. The technique shown in this paper is low-cost, reliable and highly sensitive. Chemical etching of solid Ag metal was used to produce simple, yet robust SERS substrates with broadband characteristics. Etching with ammonium hydroxide (NH4OH) and nitric acid (HNO3) helped obtain roughened Ag SERS substrates. Scanning electron microscopy (SEM) and interferometry were used to visualize and quantify surface roughness. Flattened Ag wires had inherent, but non-uniform roughness having peaks and valleys in the microscale. NH4OH treatment removed dirt and smoothened the surface, while HNO3 treatment produced a flake-like morphology with visibly more surface roughness features on Ag metal. SERS efficacy was tested using 4-methylbenzenethiol (MBT). The best SERS enhancement for 1 mM MBT was observed for Ag metal etched for 30 s in NH4OH followed by 10 s in HNO3. Further, MBT could be quantified with detection limits of 1 pM and 100 µM, respectively, using 514 nm and 1064 nm Raman spectrometers. Thus, a rapid and less energy intensive method for producing solid Ag SERS substrate and its efficacy in analyte sensing was demonstrated.This work was financially supported by Home Office UK through the SBRI programme of Innovate UK, Grant No. SBRI_HO_202_007 (HOS/14/003). S. Wijesuriya acknowledges the fellowship for her Ph.D. from Brunel Institute for Bioengineering, Brunel University. We also acknowledge the support from Brunel University—RCUK fund for open access publishing

    Buttressing staples with cholecyst-derived extracellular matrix (CEM) reinforces staple lines in an ex vivo peristaltic inflation model

    Get PDF
    This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ Springer Science + Business Media, LLC 2008Background - Staple line leakage and bleeding are the most common problems associated with the use of surgical staplers for gastrointestinal resection and anastomotic procedures. These complications can be reduced by reinforcing the staple lines with buttressing materials. The current study reports the potential use of cholecyst-derived extracellular matrix (CEM) in non-crosslinked (NCEM) and crosslinked (XCEM) forms, and compares their mechanical performance with clinically available buttress materials [small intestinal submucosa (SIS) and bovine pericardium (BP)] in an ex vivo small intestine model. Methods - Three crosslinked CEM variants (XCEM0005, XCEM001, and XCEM0033) with different degree of crosslinking were produced. An ex vivo peristaltic inflation model was established. Porcine small intestine segments were stapled on one end, using buttressed or non-buttressed surgical staplers. The opened, non-stapled ends were connected to a peristaltic pump and pressure transducer and sealed. The staple lines were then exposed to increased intraluminal pressure in a peristaltic manner. Both the leak and burst pressures of the test specimens were recorded. Results - The leak pressures observed for non-crosslinked NCEM (137.8 ± 22.3 mmHg), crosslinked XCEM0005 (109.1 ± 14.1 mmHg), XCEM001 (150.1 ± 16.0 mmHg), XCEM0033 (98.8 ± 10.5 mmHg) reinforced staple lines were significantly higher when compared to non-buttressed control (28.3 ± 10.8 mmHg) and SIS (one and four layers) (62.6 ± 11.8 and 57.6 ± 12.3 mmHg, respectively) buttressed staple lines. NCEM and XCEM were comparable to that observed for BP buttressed staple lines (138.8 ± 3.6 mmHg). Only specimens with reinforced staple lines were able to achieve high intraluminal pressures (ruptured at the intestinal mesentery), indicating that buttress reinforcements were able to withstand pressure higher than that of natural tissue (physiological failure). Conclusions - These findings suggest that the use of CEM and XCEM as buttressing materials is associated with reinforced staple lines and increased leak pressures when compared to non-buttressed staple lines. CEM and XCEM were found to perform comparably with clinically available buttress materials in this ex vivo model.Enterprise Irelan

    Amine functionalization of cholecyst-derived extracellular matrix with generation 1 PAMAM dendrimer

    Get PDF
    This document is the unedited author's version of a Submitted Work that was subsequently accepted for publication in Biomacromolecules, copyright © American Chemical Society after peer review. To access the final edited and published work, see http://pubs.acs.org/doi/pdf/10.1021/bm701055k.A method to functionalize cholecyst-derived extracellular matrix (CEM) with free amine groups was established in an attempt to improve its potential for tethering of bioactive molecules. CEM was incorporated with Generation-1 polyamidoamine (G1 PAMAM) dendrimer by using N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide and N-hydroxysuccinimide cross-linking system. The nature of incorporation of PAMAM dendrimer was evaluated using shrink temperature measurements, Fourier transform infrared (FTIR) assessment, ninhydrin assay, and swellability. The effects of PAMAM incorporation on mechanical and degradation properties of CEM were evaluated using a uniaxial mechanical test and collagenase degradation assay, respectively. Ninhydrin assay and FTIR assessment confirmed the presence of increasing free amine groups with increasing quantity of PAMAM in dendrimer-incorporated CEM (DENCEM) scaffolds. The amount of dendrimer used was found to be critical in controlling scaffold degradation, shrink temperature, and free amine content. Cell culture studies showed that fibroblasts seeded on DENCEM maintained their metabolic activity and ability to proliferate in vitro. In addition, fluorescence cell staining and scanning electron microscopy analysis of cell-seeded DENCEM showed preservation of normal fibroblast morphology and phenotype
    corecore