Circuits and circuit testing for spaceborne redundant digital systems Special technical report no. 3

Design and testing of majority logic redundancy for spaceborne and GSE digital system

The effect of the low Earth orbit environment on space solar cells: Results of the Advanced Photovoltaic Experiment (S0014)

The results of post-flight performance testing of the solar cells flown on the Advanced Photovoltaic Experiment are reported. Comparison of post-flight current-voltage characteristics with similar pre-flight data revealed little or no change in solar cell conversion efficiency, confirming the reliability and endurance of space photovoltaic cells. This finding is in agreement with the lack of significant physical changes in the solar cells despite nearly six years in the low Earth orbit environment

Monte Carlo approach of the islanding of polycrystalline thin films

We computed by a Monte Carlo method derived from the Solid on Solid model, the evolution of a polycrystalline thin film deposited on a substrate during thermal treatment. Two types of substrates have been studied: a single crystalline substrate with no defects and a single crystalline substrate with defects. We obtain islands which are either flat (i.e. with a height which does not overcome a given value) or grow in height like narrow towers. A good agreement was found regarding the morphology of numerical nanoislands at equilibrium, deduced from our model, and experimental nanoislands resulting from the fragmentation of YSZ thin films after thermal treatment.Comment: 20 pages, 7 figure

Peeled film GaAs solar cells for space power

Gallium arsenide (GaAs) peeled film solar cells were fabricated, by Organo-Metallic Vapor Phase Epitaxy (OMVPE), incorporating an aluminum arsenide (AlAs) parting layer between the device structure and the GaAs substrate. This layer was selectively removed by etching in dilute hydrofloric (HF) acid to release the epitaxial film. Test devices exhibit high series resistance due to insufficient back contact area. A new design is presented which uses a coverglass superstrate for structural support and incorporates a coplanar back contact design. Devices based on this design should have a specific power approaching 700 W/Kg

Making internal fixation work with limited bone stock

Fractures are common in small animal practice and there are many options for managing them. Plates and screws remain a popular means to manage many fractures; however, some fractures are sufficiently close to a joint (juxta-articular), that they limit the amount of bone available to achieve a standard stable plate and screw fixation. This article discusses the options to achieve a stable internal fixation when there is limited bone stock

Influence of surfactants on the structure of titanium oxide gels : experiments and simulations

We report here on experimental and numerical studies of the influence of surfactants on mineral gel synthesis. The modification of the gel structure when the ratios water-precursor and water-surfactant vary is brought to the fore by fractal dimension measures. A property of {\em polydispersity of the initial hydrolysis} is proposed to explain these results, and is successfuly tested through numerical experiments of three dimensional chemically limited aggregation.Comment: 12 pages, 4 Postscript figures, uses RevTe

Fluctuating Bond Aggregation: a Model for Chemical Gel Formation

The Diffusion-Limited Cluster-Cluster Aggregation (DLCA) model is modified by including cluster deformations using the {\it bond fluctuation} algorithm. From 3$d$ computer simulations, it is shown that, below a given threshold value $c_g$ of the volumic fraction $c$, the realization of all intra-aggregate bonding possibilities prevents the formation of a gelling network. For $c>c_g$, the sol-gel transition occurs at a time $t_g$ which, in contrast to DLCA, doesnot diverge with the box size. Several results are reported including small angle scattering curves and possible applications are discussed.Comment: RevTex, 9 pages + 3 postscript figures appended using "uufiles". To appear in Phys. Rev. Let

Three-dimensional coherent X-ray diffraction imaging of a ceramic nanofoam: determination of structural deformation mechanisms

Ultra-low density polymers, metals, and ceramic nanofoams are valued for their high strength-to-weight ratio, high surface area and insulating properties ascribed to their structural geometry. We obtain the labrynthine internal structure of a tantalum oxide nanofoam by X-ray diffractive imaging. Finite element analysis from the structure reveals mechanical properties consistent with bulk samples and with a diffusion limited cluster aggregation model, while excess mass on the nodes discounts the dangling fragments hypothesis of percolation theory.Comment: 8 pages, 5 figures, 30 reference

Band Formation during Gaseous Diffusion in Aerogels

We study experimentally how gaseous HCl and NH_3 diffuse from opposite sides of and react in silica aerogel rods with porosity of 92 % and average pore size of about 50 nm. The reaction leads to solid NH_4Cl, which is deposited in thin sheet-like structures. We present a numerical study of the phenomenon. Due to the difference in boundary conditions between this system and those usually studied, we find the sheet-like structures in the aerogel to differ significantly from older studies. The influence of random nucleation centers and inhomogeneities in the aerogel is studied numerically.Comment: 7 pages RevTex and 8 figures. Figs. 4-8 in Postscript, Figs. 1-3 on request from author

A Silicon, Carbon and Deuterium NMR Investigation of Molecular Templating in Amorphous Silicas

The precise pore sizes defined by crystalline zeolite lattices have led to intensive research on zeolite membranes. Unfortunately zeolites have proven to be extremely difficult to prepare in a defect-free thin film form needed for membrane flux and selectivity. We introduce tetrapropylammonium TPA (a structure directing agent for zeolite ZSM-5) into a silica sol and exploit the development of high solvation stresses to create templated amorphous silicas with pore apertures comparable in size to those of ZSM-5. {sup 29}Si and {sup 2}H NMR experiments were performed to evaluate the efficacy of our templating approach. The {sup 29}Si NMR spectrum of the silica matrix was observed by an intermolecular cross-polarization experiment between the {sup 1}H nuclei of TPA and the {sup 29}Si nuclei in the silica matrix. The efficiency of the cross-polarization interaction was used to investigate the degree to which the matrix formed a tight cage surrounding the template molecule. Normally prepared xerogel materials exhibited only weak interactions between the two sets of nuclei. Drying under reduced pressure, where solvation stresses are maximized, resulted in significantly increased interactions. Analogous materials were prepared using fully deuterated TPA. The {sup 2}H NMR wideline spectra consisted of a partially narrowed resonance, corresponding to template molecules which were undergoing restricted rotational motion, and an isotropically narrowed resonance, corresponding to molecules which were undergoing rapid rotational motion. The number of isotropically rotating template molecules decreased for specimens dried under reduced pressure, consistent with improved templating of amorphous silica by TPA