MEMS-actuated wavelength drop filter based on microsphere whispering gallery modes

MEMS-enabled tuneable optical coupling between optical microsphere resonators and optical fibre waveguides is reported. We describe the design, fabrication and experimental characterization of a MEMS platform, based on electrothermal actuators, which controls the resonator-to-waveguide separation. We compare the simulated and experimental displacements of the actuators in an unloaded and loaded state, where the load is a 1 mm optical spherical resonator. We then demonstrate the proof of concept application of selective wavelength dropping using the MEMS platform by modulating the coupling between the spherical resonator and a tapered optical fibre waveguide

Modeling and characterization of a vernier latching MEMS variable optical attenuator

We report on the modeling and testing of a Vernier latched MEMS variable optical attenuator (VOA) which uses chevron electrothermal microactuators to control fiber-to-fiber optical power coupling. The use of microlatches has the advantage of holding the mechanical position of the fiber, and therefore the level of attenuation, with no electrical energy supplied except only to change the attenuation. Results of analytical electro-thermo-mechanical models of the device are obtained and compared with experimental test results, showing a good agreement. A step resolution of 0.5 μm for this multi-state latched device is achieved using a Vernier latch approach. This incremental step size is smaller than previously reported latched microactuators. The VOA demonstrated an attenuation range of over 47 dB and an insertion loss of 1 dB. The wavelength dependent loss across the optical communications C-band is 1.4 dB at 40 dB attenuation and the 10-90% transition time of the unlatched VOA is measured to be 1.7 ms

Single mode fiber variable optical attenuator based on a ferrofluid shutter

We report on the fabrication and characterization of a single-mode fiber variable optical attenuator (VOA) based on a ferrofluid shutter actuated by a magnetic field created by a low voltage electromagnet. We compare the performance of a VOA using oil-based ferrofluid, with one VOA using water-based 12 ferrofluid, and demonstrate broadband optical attenuation of up to 28 dB with polarization dependent 13 loss of 0.85 dB. Our optofluidic VOA has advantages over MEMS-based VOAs such as simple construction and the absence of mechanical moving parts

Transmissive optical fiber magnetic field sensor based on ferrofluids

A compact optical fiber magnetic field sensor is reported which relies on the magnetic field induced displacement of a ferrofluid lying in the gap between two single mode optical fibers (SMFs) that are aligned face to face. The ferrofluid displacement alters the coupling of light from the input optical fiber to the output optical fiber. When the applied magnetic field changes from 0 mT to 10 mT the optical attenuation changes from 0 dB to -28 dB

Novel polymer materials for low-cost nitro vapor detection sensors

Current commercial sensors for explosive vapours are high cost bulky equipment not amenable to mass production and thus prevents their mass deployment within society. Our research objective is to create compact sensors that are not only portable but of such low cost that they can be installed in buildings in the same way as smoke detectors. We have developed novel polymers whose properties have been tailored to give them a higher affinity to target nitro group (NO2) bearing molecules associated with explosives. The polymers have been grown electrochemically onto miniature interdigitated electrode platforms yielding miniature sensors. Novel porous polymers based sensors are demonstrated which yield a detection level of 200 ppb of nitro vapours and can be manufactured at low-unit-cost

Factors Affecting Laminar Boundary Layer Measurements in a Supersonic Stream

The observed discrepancy at supersonic speeds between theoretical and apparent experimental average flat plate friction-drag coefficients calculated from boundary layer total-pressure surveys was investigated. Effects of the total-pressure probe, heat transfer through the leading edge region, change in leading-edge radius and strength of the leading-edge wave, possible early transition to turbulent flow or bursts of turbulence, and the slight stream-wise pressure gradient inherent in flat plate flow were investigated for plates with very sharp leading edges. Only one of these factors, the effect of the total-pressure probe, was found to be significant. Total-pressure probes of different tip heights, when placed in laminar boundary layers developing under identical conditions, were found to yield different values of friction drag coefficient. Extrapolation of these measurements indicates that a probe of vanishing size would yield the theoretical predicted values of average flat plate friction-drag coefficients. A correlation describing the relation between the friction-drag discrepancy and the probe tip height is presented

Chemicapacitors as a versatile platform for miniature gas and vapor sensors

Recent years have seen the rapid growth in the need for sensors throughout all areas of society including environmental sensing, health-care, public safety and manufacturing quality control. To meet this diverse need, sensors have to evolve from specialized and bespoke systems to miniaturized, low-power, low-cost (almost disposable) ubiquitous platforms. A technology that has been developed which gives a route to meet these challenges is the chemicapacitor sensor. To date the commercialization of these sensors has largely been restricted to humidity sensing, but in this review we examine the progress over recent years to expand this sensing technology to a wide range of gases and vapors. From sensors interrogated with laboratory instrumentation, chemicapacitor sensors have evolved into miniaturized units integrated with low power readout electronics that can selectively detect target molecules to ppm and sub-ppm levels within vapor mixtures