6 research outputs found
Recommended from our members
High fidelity frictional models for MEMS.
The primary goals of the present study are to: (1) determine how and why MEMS-scale friction differs from friction on the macro-scale, and (2) to begin to develop a capability to perform finite element simulations of MEMS materials and components that accurately predicts response in the presence of adhesion and friction. Regarding the first goal, a newly developed nanotractor actuator was used to measure friction between molecular monolayer-coated, polysilicon surfaces. Amontons law does indeed apply over a wide range of forces. However, at low loads, which are of relevance to MEMS, there is an important adhesive contribution to the normal load that cannot be neglected. More importantly, we found that at short sliding distances, the concept of a coefficient of friction is not relevant; rather, one must invoke the notion of 'pre-sliding tangential deflections' (PSTD). Results of a simple 2-D model suggests that PSTD is a cascade of small-scale slips with a roughly constant number of contacts equilibrating the applied normal load. Regarding the second goal, an Adhesion Model and a Junction Model have been implemented in PRESTO, Sandia's transient dynamics, finite element code to enable asperity-level simulations. The Junction Model includes a tangential shear traction that opposes the relative tangential motion of contacting surfaces. An atomic force microscope (AFM)-based method was used to measure nano-scale, single asperity friction forces as a function of normal force. This data is used to determine Junction Model parameters. An illustrative simulation demonstrates the use of the Junction Model in conjunction with a mesh generated directly from an atomic force microscope (AFM) image to directly predict frictional response of a sliding asperity. Also with regards to the second goal, grid-level, homogenized models were studied. One would like to perform a finite element analysis of a MEMS component assuming nominally flat surfaces and to include the effect of roughness in such an analysis by using a homogenized contact and friction models. AFM measurements were made to determine statistical information on polysilicon surfaces with different roughnesses, and this data was used as input to a homogenized, multi-asperity contact model (the classical Greenwood and Williamson model). Extensions of the Greenwood and Williamson model are also discussed: one incorporates the effect of adhesion while the other modifies the theory so that it applies to the case of relatively few contacting asperities
The structural-acoustic energy finite-element method and energy boundary-element method
It is important to identify vibrational energy noise paths to reduce the sound field in complicated engineering systems, such as aircraft and automobiles. However, there is no easy method to model the behavior of real plates and acoustic enclosures at high frequencies. A method called Energy Flow Analysis has been developed to predict the structural responses in homogenous systems such as rods, beams, plates, and acoustic spaces. Additional procedures have been built on these results to predict the responses in coupled systems consisting of rods, beams, and plates. In this research, a structural-acoustic coupling relationship is proposed for energy flow analysis of plates and acoustical spaces. The coupling relationship is derived in terms of plate radiation efficiency. Analytical expressions for radiation efficiency of simple models are readily available in the literature as a function of frequency, geometry, and material properties. The structural-acoustic coupling relationship was implemented into an energy finite element model. The energy finite element method coupling relationship has the capability to implement several discrete values of radiation efficiencies across a radiating plate if the need arises. Energy Flow Analysis is a method to describe sound radiation and to be able to model and predict the structural-acoustic energy levels. Experimental results of a coupled structural-acoustic system were measured and compared to the energy finite element method as a verification study of the proposed coupling relationship. The structural-acoustic coupling relationship was also formulated for an energy boundary element model. A sensitivity analysis method was also formulated and implemented for the energy finite element method
Recommended from our members
Interferometric Measurement for Improved Understanding of Boundary Effects in Micromachined Beams
Micromachined beams are commonly used to measure material properties in MEMS. Such measurements are complicated by the fact that boundary effects at the ends of the beams have a significant effect on the properties being measured. In an effort to improve the accuracy and resolution of such measurements, we are conducting a study of support post compliance in cantilever and fixed-fixed beams. Three different support post designs have been analyzed by finite element modeling. The results are then compared to measurements made on actual devices using interferometry. Using this technique, the accuracy of measurements of Young's modulus has been improved. Continuing work will also improve the measurement of residual stress
Recommended from our members
A Small Area In-Situ MEMS Test Structure to Accurately Measure Fracture Strength by Electrostatic Probing
We have designed, fabricated, tested and modeled a first generation small area test structure for MEMS fracture studies by electrostatic rather than mechanical probing. Because of its small area, this device has potential applications as a lot monitor of strength or fatigue of the MEMS structural material. By matching deflection versus applied voltage data to a 3-D model of the test structure, we develop high confidence that the local stresses achieved in the gage section are greater than 1 GPa. Brittle failure of the polycrystalline silicon was observed
Recommended from our members
Torsional Ratcheting Actuating System
A new type of surface micromachined ratcheting actuation system has been developed at the Microelectronics Development Laboratory at Sandia National Laboratories. The actuator uses a torsional electrostatic comb drive that is coupled to an external ring gear through a ratcheting scheme. The actuator can be operated with a single square wave, has minimal rubbing surfaces, maximizes comb finger density, and can be used for open-loop position control. The prototypes function as intended with a minimum demonstrated operating voltage of 18V. The equations of motion are developed for the torsional electrostatic comb drive. The resonant frequency, voltage vs. displacement and force delivery characteristics are predicted and compared with the fabricated device's performance
Recommended from our members
Microdiagnostic Lab on a Chip - LDRD Final Report
Polycrystalline silicon (polysilicon) surface micromachining is a new technology for building micrometer ({micro}m) scale mechanical devices on silicon wafers using techniques and process tools borrowed from the manufacture of integrated circuits. Sandia National Laboratories has invested a significant effort in demonstrating the viability of polysilicon surface micromachining and has developed the Sandia Ultraplanar Micromachining Technology (SUMMiT V{trademark} ) process, which consists of five structural levels of polysilicon. A major advantage of polysilicon surface micromachining over other micromachining methods is that thousands to millions of thin film mechanical devices can be built on multiple wafers in a single fabrication lot and will operate without post-processing assembly. However, if thin film mechanical or surface properties do not lie within certain tightly set bounds, micromachined devices will fail and yield will be low. This results in high fabrication costs to attain a certain number of working devices. An important factor in determining the yield of devices in this parallel-processing method is the uniformity of these properties across a wafer and from wafer to wafer. No metrology tool exists that can routinely and accurately quantify such properties. Such a tool would enable micromachining process engineers to understand trends and thereby improve yield of micromachined devices. In this LDRD project, we demonstrated the feasibility of and made significant progress towards automatically mapping mechanical and surface properties of thin films across a wafer. The MEMS parametrics measurement team has implemented a subset of this platform, and approximately 30 wafer lots have been characterized. While more remains to be done to achieve routine characterization of all these properties, we have demonstrated the essential technologies. These include: (1) well-understood test structures fabricated side-by-side with MEMS devices, (2) well-developed analysis methods, (3) new metrologies (i.e., long working distance interferometry) and (4) a hardware/software platform that integrates (1), (2) and (3). In this report, we summarize the major focus areas of our LDRD project. We describe the contents of several articles that provide the details of our approach. We also describe hardware and software innovations we made to realize a fully automatic wafer prober system for MEMS mechanical and surface property characterization across wafers and from wafer-lot to wafer-lot