The Effect on Rudder Control of Slip Stream Body, and Ground Interference

This investigation was undertaken to determine the relative effects of those factors which may interfere with the rudder control of an airplane, with especial reference to the process of landing. It shows that ground interference is negligible, but that the effects of a large rounded body and of the slip stream may combine to interfere seriously with rudder control at low flying speeds and when taxiing

The Determination of the Effective Resistance of a Spindle Supporting a Model Airfoil

An attempt was made to determine the effect of spindle interference on the lift of the airfoil by measuring moments about the axis parallel to the direction of air flow. The values obtained are of the same degree as the experimental error, and for the present this effect will be neglected. The results obtained using a U.S.A. 15 wing (plotted here) show that the correction is nearly constant from 0 degrees to 10 degrees incidence and that at greater angles its value becomes erratic. At such angles, however, the wing drag is so high that the spindle correction and its attendant errors become relatively small and unimportant

Preliminary Experiments to Determine Scale and Slip-Stream Effects on a 1/24th Size Model of a JN4H Biplane

This work was undertaken to obtain results on a small model of a complete airplane which might be used for comparison with corresponding tests made in full flight. Somewhat similar tests have been previously made at various other laboratories; but as certain discrepancies exist between corresponding tests in different tunnels, it has been deemed advisable to obtain a direct comparison for this particular installation. The present work covers tests on a one-twenty-fourth scale model at speeds varying from 6.7 m/sec. (15 m.p.h.) to 40.2 m/sec, (90 m.p.h.). A slip stream correction has been obtained by the use of a small belt-driven propeller mounted in front of the model, and force coefficients thus obtained are compared with the measurements of the same forces made in full flight on a geometrically similar airplane. This report gives lift, drag, and longitudinal moment values obtained in tests of a particularly accurate model over a wide range of speeds. A measure of the slip stream corrections on lift and drag forces was obtained by the use of a power-driven model propeller. Measurements were also made of forces and longitudinal moments for all angles from 0 degree to 360 degrees

Langley Field wind tunnel apparatus

The difficulties experienced in properly holding thin tipped or tapered airfoils while testing on an N.P.L. type aerodynamic balance even at low air speeds, and the impossibility of holding even solid metal models at the high speeds attainable at the National Advisory Committee's wind tunnel, necessitated the design of a balance which would hold model airfoils of any thickness and at speeds up to 150 m.p.h. In addition to mechanical strength and rigidity, it was highly desirable that the balance readings should require a minimum amount of correction and mathematical manipulation in order to obtain the lift and drag coefficients and the center of pressure. The balance described herein is similar to one in use at the University of Gottingen, the main difference lying in the addition of a device for reading the center of pressure directly, without the necessity of any correction whatsoever. Details of the design and operation of the device are given

A double-helix neutron detector using micron-size B-10 powder

A double-helix electrode configuration is combined with a $^{10}$B powder coating technique to build large-area (9 in $\times$ 36 in) neutron detectors. The neutron detection efficiency for each of the four prototypes is comparable to a single 2-bar $^3$He drift tube of the same length (36 in). One unit has been operational continuously for 18 months and the change of efficiency is less than 1%. An analytic model for pulse heigh spectra is described and the predicted mean film thickness agrees with the experiment to within 30%. Further detector optimization is possible through film texture, power size, moderator box and gas. The estimated production cost per unit is less than 3k US\$ and the technology is thus suitable for deployment in large numbers

Aerodynamic properties of thick airfoils II

This investigation is an extension of NACA report no. 75 for the purpose of studying the effect of various modifications in a given wing section, including changes in thickness, height of lower camber, taper in thickness, and taper in plan form with special reference to the development of thick, efficient airfoils. The method consisted in testing the wings in the NACA 5-foot wind tunnel at speeds up to 50 meters (164 feet) per second while they were being supported on a new type of wire balance. Some of the airfoils developed showed results of great promise. For example, one wing (no. 81) with a thickness in the center of 4.5 times that of the U. S. A. 16 showed both uniformly high efficiency and a higher maximum lift than this excellent section. These thick sections will be especially useful on airplanes with cantilever construction. (author

Pressure Distribution over Thick Airfoils - Model Tests

This investigation was undertaken to study the distribution of loading over thick wings of various types. The unloading on the wing was determined by taking the pressure at a number of holes on both the upper and lower surfaces of a model wing in the wind tunnel. The results from these tests show, first, that the distribution of pressure over a thick wing of uniform section is very little different from that over a thin wing; second, that wings tapering either in chord or thickness have the lateral center of pressure, as would be expected, slightly nearer the center of the wings; and, third, that wings tapering in plan form and with a section everywhere proportional to the center section may be considered to have a loading at any point which is proportional to the chord when compared to a wing with a similar constant section. These tests confirm the belief that wings tapering both in thickness and plan form are of considerable structural value because the lateral center of pressure is thereby moved toward the center of the span