152 research outputs found
Evaluation of engineering properties of calcium sulfoaluminate cement-based concretes reinforced with different types of fibers
Calcium sulfoaluminate (CSA) cement has recently gained increased attention due to its lower amount of CO2 emissions, as compared to that of the ordinary Portland cement (OPC). This paper evaluates the impact of different types of fibers on the engineering features of CSA-based concretes at different water-cement ratios of 0.35 and 0.28. In this study, metallic fibers including double hooked-end steel fibers and hooked-end steel fibers, and non-metallic fibers (i.e., polyvinyl alcohol (PVA) fibers) were utilized at fiber content of 1%. The mechanical properties of concretes were assessed at different curing ages. Dimensional stability of the concrete mixes was also examined. The morphology of the fractured specimens was studied by using the SEM method. The results indicate that the engineering properties of concrete were improved by introducing fibers to the concrete, irrespective of fiber type. The results show that DHE steel fiber has an important effect on the flexural performance of CSA cement-based concretes and results in deflection-hardening behavior. It was observed that fibers and particularly PVA fibers cause a decrease in shrinkage deformation. Microstructure tests demonstrate that prismatic ettringite is the main hydration product of CSA cement-based concrete. The SEM observation also confirms that the inclusion of CSA cement in concrete improves the cohesiveness between the fibers and cement matrix
Review of the Main Mechanical Testing Methods for Interlayer Characterization in Laminated Glass
In the last decades, the use of structural glass has increased exponentially. The reliability of brittle structural glass elements is considerably improved if laminated glass elements are chosen because, in this case, a redistribution of internal forces is permitted once a limited breakage occurs. Thus, instead of monolithic glass, composite materials consisting of two or more glass plies bonded together using a polymeric film as an interlayer are used. In the event of glass failure, because of the chemical bond between the different materials, the adhesion to the interlayer prevents glass fragments from scattering. To design structural elements, the definition of the mechanical features of the interlayer is necessary. However, several standards and techniques can be applied, considering the characterization of either the interlayer itself or the laminated glass. The paper reviews the main existing methods and focuses on the standard suggested by the CEN/TS 19100:2021, analyzing in detail the effect of the different parameters involved. A numerical model is presented to account for the effect of the stress level, glass, and interlayer thickness. Although the standard leaves a certain degree of freedom in choosing those parameters, in some cases the results can differ
Parametric Analyses of the Response of Masonry Walls with Reinforced Plaster
This paper presents the results of a parametric study on the response of unreinforced and retrofitted masonry specimens. The adopted strengthening technique is the steel-reinforced plaster, which is very commonly used but it is not supported by a proper theoretical and experimental characterization in the scientific literature. The aim was to investigate the main parameters that affect the structural performances of the walls. Several numerical models were implemented using the finite element method to analyze the influence of the bricks' arrangements, the mechanical properties of the mortar joints, the number of connectors, and the mechanical properties and thickness of the plaster coating. A concrete damage plasticity model was adopted to describe the bricks, the mortar joints, and the plaster behaviors. For the unreinforced specimens, the outcomes confirmed that the mortar strength had a significant influence on the performance of the wall, together with the presence of potential weaknesses in the bricks, while the bond effect was negligible. For reinforced walls, the connectors do not have a significant influence on retrofitted wall capacity but may prevent instability if a proper number is considered. Furthermore, the strength of the plaster coating does not affect the collapse load significantly, while increasing the fracture energy, which can be produced, for instance, by using fiber-reinforced concrete, increases the capacity of retrofitted walls, with more limited damage. Finally, an increase in the plaster thickness may be beneficial in terms of collapse load, even though greater thickness may increase the seismic masses significantly
DMTs and Covid-19 severity in MS: a pooled analysis from Italy and France
We evaluated the effect of DMTs on Covid-19 severity in patients with MS, with a pooled-analysis of two large cohorts from Italy and France. The association of baseline characteristics and DMTs with Covid-19 severity was assessed by multivariate ordinal-logistic models and pooled by a fixed-effect meta-analysis. 1066 patients with MS from Italy and 721 from France were included. In the multivariate model, anti-CD20 therapies were significantly associated (OR = 2.05, 95%CI = 1.39–3.02, p < 0.001) with Covid-19 severity, whereas interferon indicated a decreased risk (OR = 0.42, 95%CI = 0.18–0.99, p = 0.047). This pooled-analysis confirms an increased risk of severe Covid-19 in patients on anti-CD20 therapies and supports the protective role of interferon
Overall response of 2-ply laminated glass plates under out-of-plane loading
The results of an experimental and numerical investigation on the mechanical response of undamaged and damaged 2-ply Laminated Glass (LG) plates with different interlayers are presented in the paper. Three different interlayers, polyvinyl butyral (PVB), SentryGlas (SG) and Saflex DG41 (DG41) characterized by different rheological properties and fully tempered glass plates were considered. Simply supported plates under out of plane loads were tested in three different configurations: configuration 0, undamaged; configuration I, partially damaged, with a broken ply below (bottom ply) and configuration II, partially damaged, with a broken ply above (top ply). In the three configurations the top ply is always subjected to compression while the bottom one is in tension. The main aspects and the different response of each configuration were discussed and compared. Experimental results highlighted the influence of the interlayer properties on both the pre- and post-breakage behavior. Moreover, numerical models were developed to reproduce the experimental results. For the post-breakage response two different strategies were developed: a) the equivalent temperature variation and b) elastic-brittle constitutive law. Differences and advantages associated with both solutions are discussed. Finally, extensive parametric numerical analyses are proposed to underline the influence on the mechanical response of different parameters: i) plate geometry (size effect); ii) interlayer thickness; iii) glass thickness; iv) additional glass ply (3-ply LG plate). It is underlined that the size effect plays an important role on the mechanical response of LG plates and it should be always considered in the design. The numerical findings were used to define a critical length from which the plates behave as monolithic, independently of the stiffness of the interlayer
Structural analysis and design of reinforced concrete bridge corbels
Post-installed systems for the anchorage of safety barriers to bridge corbels are widely used today thanks to their flexibility and easiness of installation. Because of commonly found in situ boundary constraints, however, the design requirements for post-installed fasteners and rebars are frequently not satisfied or only partially satisfied. This paper assesses the mechanical response of a corbel where an innovative solution concerning the placement of post-installed reinforcement in reinforced concrete members was suggested. With reference to the refurbishment of bridge curbs, which usually requires concrete removal in the damaged top layers, the proposed method was based on the introduction of additional U-shaped post-installed rebars connecting the existing portion of the corbel to the newly cast top layer, in order to allow the transfer of the tension pull-out force exerted by the posts restraining the safety barrier. The layout investigated in this paper consisted of three anchors connecting the baseplate of the post supporting the safety barrier to the corbel (a layout commonly found in Italy). These anchors transfer the external actions (bending moment and shear) to the corbel thanks to the formation of a strut-and-tie system where the U-shaped rebars and the existing reinforcement play a crucial role. A strut-and-tie model of the corbel was presented to allow the use of a simplified approach to assess the safety of the corbel. The tests on real-scale specimens were also modeled numerically and additional models were considered to evaluate the effect of characteristics parameters (i.e., size of the corbel, existing shear reinforcement, etc.) on the overall response of the corbel
Influence of steel microfiber and microsilica on behavior of high performance cement based composites
- …