Nanoscale residual stress and adhesion assessment

No Abstract

The Folding process of Human Profilin-1, a novel protein associated with familial amyotrophic lateral sclerosis

Human profilin-1 is a novel protein associated with a recently discovered form of familial amyotrophic lateral sclerosis. This urges the characterization of possible conformational states, different from the fully folded state, potentially able to initiate self-assembly. Under native conditions, profilin-1 is monomeric and possesses a well-defined secondary and tertiary structure. When incubated at low pH or with high urea concentrations, profilin-1 remains monomeric but populates unfolded states exhibiting larger hydrodynamic radius and disordered structure, as assessed by dynamic light scattering, far-UV circular dichroism and intrinsic fluorescence. Refolding from the urea-unfolded state was studied at equilibrium and in real-time using a stopped-flow apparatus. The results obtained with intrinsic fluorescence and circular dichroism indicate a single phase without significant changes of the corresponding signals before the major refolding transition. However, such a transition is preceded by a burst phase with an observed increase of ANS fluorescence, which indicates the conversion into a transiently populated collapsed state possessing solvent-exposed hydrophobic clusters. Kinetic analysis reveals that such state has a conformational stability comparable to that of the fully unfolded state. To our knowledge, profilin-1 is the first example of an amyloid-related protein where folding occurs in the absence of thermodynamically stable partially folded states

Dense and cellular zirconia produced by gel casting with agar: preparation and high temperature characterization

A modified gel-casting process was developed to produce both dense and highly porous (40% volume) yttria tetragonal zirconia polycrystal (Y-TZP) using agar, a natural polysaccharide, as gelling agent. A fugitive phase, made of commercial polyethylene spheres, was added to the ceramic suspension before gelling to produce cellular ceramic structures. The characterization of the microstructural features of both dense and cellular ceramics was carried out by FEG SEM analysis of cross-sections produced by focused ion beam. The mechanical properties of the components were characterized at room temperature by nanoindentation tests in continuous stiffness measurement mode, by investigating the direct effect of the presence of residual microporosity. The presence of a diffuse residual microporosity from incomplete gel deaeration resulted in a decay of the bending strength and of the elastic modulus. The mechanical behavior of both dense and cellular zirconia (in terms of elastic modulus, flexural strength, and deformation at rupture) was investigated by performing four-point bending tests at the temperature of 1500°C

Niobium–niobium oxide multilayered coatings for corrosion protection of proton-irradiated liquid water targets for [18F] production

Abstract Chemically inert coatings on Havar ® entrance foils of the targets for [ 18 F] production via proton irradiation of enriched water at pressurized conditions are needed to decrease the amount of ionic contaminants released from Havar ® . During current investigation, magnetron sputtered niobium and niobium oxide were chosen as the candidates for protective coatings because of their superior chemical resistance. Aluminated quartz substrates allowed us to verify the protection efficiency of the desirable coatings as diffusion barriers. Two modeling corrosion tests based on the extreme susceptibility of aluminum to liquid gallium and acid corrosion were applied. As far as niobium coatings obtained by magnetron sputtering are columnar, the grain boundaries provide a fast diffusion path for active species of corrosive media to penetrate and to corrode the substrate. Amorphous niobium oxide films obtained by reactive magnetron sputtering showed superior barrier properties according to the corrosion tests performed. In order to prevent degrading of brittle niobium oxide at high pressures, multilayers combining high ductility of niobium with superior diffusion barrier efficiency of niobium oxide were proposed. The intercalation of niobium oxide interlayers was proved to interrupt the columnar grain growth of niobium during sputtering, resulting in improved diffusion barrier efficiency of obtained multilayers. The thin layer multilayer coating architecture with 70 nm bi-layer thickness was found preferential because of higher thermal stability

Influence of the Silver Content on Mechanical Properties of Ti-Cu-Ag Thin Films

In this work, the ternary titanium, copper, and silver (Ti-Cu-Ag) system is investigated as a potential candidate for the production of mechanically robust biomedical thin films. The coatings are produced by physical vapor deposition-magnetron sputtering (MS-PVD). The composite thin films are deposited on a silicon (100) substrate. The ratio between Ti and Cu was approximately kept one, with the variation of the Ag content between 10 and 35 at.%, while the power on the targets is changed during each deposition to get the desired Ag content. Thin film characterization is performed by X-ray diffraction (XRD), nanoindentation (modulus and hardness), to quantitatively evaluate the scratch adhesion, and atomic force microscopy to determine the surface topography. The residual stresses are measured by focused ion beam and digital image correlation method (FIB-DIC). The produced Ti-Cu-Ag thin films appear to be smooth, uniformly thick, and exhibit amorphous structure for the Ag contents lower than 25 at.%, with a transition to partially crystalline structure for higher Ag concentrations. The Ti-Cu control film shows higher values of 124.5 GPa and 7.85 GPa for modulus and hardness, respectively. There is a clear trend of continuous decrease in the modulus and hardness with the increase of Ag content, as lowest value of 105.5 GPa and 6 GPa for 35 at.% Ag containing thin films. In particular, a transition from the compressive (-36.5 MPa) to tensile residual stresses between 229 MPa and 288 MPa are observed with an increasing Ag content. The obtained results suggest that the Ag concentration should not exceed 25 at.%, in order to avoid an excessive reduction of the modulus and hardness with maintaining (at the same time) the potential for an increase of the antibacterial properties. In summary, Ti-Cu-Ag thin films shows characteristic mechanical properties that can be used to improve the properties of biomedical implants such as Ti-alloys and stainless steel

Damage progression in thermal barrier coating systems during thermal cycling: A nano-mechanical assessment

This paper studies how the nano-mechanical properties of thermal barrier coatings (TBCs) vary during thermal cycling, as a way to shed new light on their failure mechanisms. In particular, high-throughput nanoindentation revealed the evolution of hardness and elastic modulus distributions of plasma-sprayed yttria-stabilized zirconia (YSZ) top layers. The evolution of fracture toughness of the YSZ layers and the thermally grown oxide (TGO) formed onto the vacuum plasma-sprayed NiCoCrAlY bond coat were investigated by nanoindentation micro-pillar splitting. The TGO fracture toughness increases up to ≈2.5–3.5 MPa√m at the early stages of thermal cycling, followed by a rapid decrease to ≈2.0 MPa√m after a critical TGO thickness of ≈5 μm is reached. Consequently, interface damage is initially limited to short cracks within the YSZ material. As TGO thickness exceeds the critical threshold, multiple cracks originate within the TGO and join through the YSZ to form long delamination cracks. Joining is favoured by a simultaneous loss in YSZ strength, testified by a decrease in the nanomechanical properties (hardness, elastic modulus) of both high- and low-porosity top coats. This is due to microstructural changes occurring because of the continuous interplay between sintering and thermal shock cracking in the YSZ layers

Contraintes résiduelles et comportement mécanique de revêtements nickel-bore

peer reviewedTwo nickel-based coatings obtained from reducing baths are studied. The first one is studied as- deposited whereas the second one was subjected to a heat-treatment. Hardness and Young's modulus of coatings have been investigated by means of indentation tests. Results show that mechanical properties are homogenous in the whole thickness of the coating. On the other hand, the heat treatment leads on a significantly increase of hardness and modulus. Residual stresses in the coatings are studied by the incremental ring core method. Values of residual stresses are small, scattered and do not seem to be heat-treatment dependent. Without any modifications of residual stresses before and after heat treatment, mechanical properties evolutions were attributed to the microstructural modification of the coating and to the precipitation of hard phases