2,915 research outputs found
Modulated IR radiometry as a tool for the thickness control of coatings
The thickness of coatings can be determined using the data measured by Modulated IR Radiometry for sets of coatings, produced under specific controlled conditions: – Keeping constant all deposition parameters except the deposition time, coatings of approximately constant thermal transport properties, but different thickness are produced. The modulated IR phase lag signals measured for the coatings are calibrated with the help of signals obtained for homogeneous opaque reference samples of smooth surface. Quantitative results for the thermal transport properties are obtained using the inverse solution of the 2-layer thermal wave problem by which direct relations are established between the relative extrema of the inverse calibrated thermal wave phase signals measured as a function of the heating modulation frequency and the thermal coating parameters, the ratio of the effusivities coating-to-substrate, the coating's thermal diffusion time, and the coating thickness. The coating thickness values obtained by Modulated IR Radiometry are compared with the values measured by standard microscopic methods, and relative errors of 3 – 4% have been found for the coating thickness of a set of TiCO coatings on steel, presented here as an example.(undefined
The Fermi energy in oxides: assessing and understanding the limits using XPS
The Fermi energy in semiconductors can often be freely controlled across the whole energy gap by doping. This is not the case in oxides, where different mechanisms exist, which can limit the range of the Fermi energy. These limits can be caused by i) dopants having deep rather than shallow charge transition levels, ii) self-compensation where the Fermi energy dependence of the defect formation energy leads to spontaneous formation of compensating defects, iii) the change of the oxidation state of either the cations or the oxygen. The latter is particularly relevant for compounds with transition metal or rare earth cations and has been recently demonstrated to explain the low water splitting efficiency of hematite [1].
Please click Additional Files below to see the full abstract
Modulated photothermal measurements applied to multi-layer superinsulation foils
Abstract -Photothermal measurements based on modulated heating in the visible spectral range and IR detection of the thermal response are used to determine the effective thermal transport properties and the shielding properties of multi-layer superinsulation foils consisting of different numbers of aluminized mylar layers and spacer layers. The measurements have been run at ambient temperature, both at ambient pressure and at reduced pressures between 1 mbar and 300 mbar
Analysis of multifunctional oxycarbide and oxynitride thin films by modulated IR radiometry
THERMAL-WAVE MEASUREMENTS OF MULTI-LAYER SUPERINSULATION FOILS
Abstract Thermal wave measurements rely on modulated laser heating and IR detection of the thermal response, using a MCT detector with IR optics and lock-in amplifier. Both, the amplitude and the phase retardation of the thermal wave response with respect to the heating modu-lation, provide information on the effective thermal transport properties of the measured samples. Here we apply this method to determine the shielding properties of multilayer superinsulation foils, used for the thermal insulation of superconducting magnetic coils in particle accelerators, e.g. in LHC at CERN. The measurements, performed at ambient temperature and ambient and reduced pressure, have been interpreted using a theoreti-cal model, including both conductive and radiative heat transport. The results show that the radiative heat transport can be well identified, although the conductive heat transport is dominant across multi-layer samples. At reduced pressures, the conductive heat transport decrea-ses considerably and, depending on the number of spacer layers, the radiative heat transport can become dominant. Applying this new photothermal technique, the shielding efficiencies of multi-layer superinsulation foils have been compared in this work for the first time
APACHE III outcome prediction in patients admitted to the intensive care unit after liver transplantation: a retrospective cohort study
<p>Abstract</p> <p>Background</p> <p>The Acute Physiology and Chronic Health Evaluation (APACHE) III prognostic system has not been previously validated in patients admitted to the intensive care unit (ICU) after orthotopic liver transplantation (OLT). We hypothesized that APACHE III would perform satisfactorily in patients after OLT</p> <p>Methods</p> <p>A retrospective cohort study was performed. Patients admitted to the ICU after OLT between July 1996 and May 2008 were identified. Data were abstracted from the institutional APACHE III and liver transplantation databases and individual patient medical records. Standardized mortality ratios (with 95% confidence intervals) were calculated by dividing the observed mortality rates by the rates predicted by APACHE III. The area under the receiver operating characteristic curve (AUC) and the Hosmer-Lemeshow C statistic were used to assess, respectively, discrimination and calibration of APACHE III.</p> <p>Results</p> <p>APACHE III data were available for 918 admissions after OLT. Mean (standard deviation [SD]) APACHE III (APIII) and Acute Physiology (APS) scores on the day of transplant were 60.5 (25.8) and 50.8 (23.6), respectively. Mean (SD) predicted ICU and hospital mortality rates were 7.3% (15.4) and 10.6% (18.9), respectively. The observed ICU and hospital mortality rates were 1.1% and 3.4%, respectively. The standardized ICU and hospital mortality ratios with their 95% C.I. were 0.15 (0.07 to 0.27) and 0.32 (0.22 to 0.45), respectively.</p> <p>There were statistically significant differences in APS, APIII, predicted ICU and predicted hospital mortality between survivors and non-survivors. In predicting mortality, the AUC of APACHE III prediction of hospital death was 0.65 (95% CI, 0.62 to 0.68). The Hosmer-Lemeshow C statistic was 5.288 with a p value of 0.871 (10 degrees of freedom).</p> <p>Conclusion</p> <p>APACHE III discriminates poorly between survivors and non-survivors of patients admitted to the ICU after OLT. Though APACHE III has been shown to be valid in heterogenous populations and in certain groups of patients with specific diagnoses, it should be used with caution – if used at all – in recipients of liver transplantation.</p
Constraints on the χ_(c1) versus χ_(c2) polarizations in proton-proton collisions at √s = 8 TeV
The polarizations of promptly produced χ_(c1) and χ_(c2) mesons are studied using data collected by the CMS experiment at the LHC, in proton-proton collisions at √s=8 TeV. The χ_c states are reconstructed via their radiative decays χ_c → J/ψγ, with the photons being measured through conversions to e⁺e⁻, which allows the two states to be well resolved. The polarizations are measured in the helicity frame, through the analysis of the χ_(c2) to χ_(c1) yield ratio as a function of the polar or azimuthal angle of the positive muon emitted in the J/ψ → μ⁺μ⁻ decay, in three bins of J/ψ transverse momentum. While no differences are seen between the two states in terms of azimuthal decay angle distributions, they are observed to have significantly different polar anisotropies. The measurement favors a scenario where at least one of the two states is strongly polarized along the helicity quantization axis, in agreement with nonrelativistic quantum chromodynamics predictions. This is the first measurement of significantly polarized quarkonia produced at high transverse momentum
- …