Recommended drilling parameters of tungsten carbide round drills for the most optimal bone removals in oral surgery

Background. High temperatures during drilling can cause thermal osteonecrosis and abnormal wound healing. According to our best knowledge, a widely accepted recommendation for optimal drilling parameters in routine oral surgery bone removals does not exist. Purpose. Our aim was to investigate the correlations of different drilling parameters, including axial load and revolution speed on drilling temperatures and preparation times. Materials and Methods. Standard, 5 mm deep cavities were drilled in 20 PCF (lb/ft3) dens polyurethane blocks with 3 mm (50PCF) cortical layer using new and worn, 3.1mm in diameter tungsten carbide round drills. Worn drills were used in 50 impacted third molar operations before. Axial loads of 3N, 10N, and 25N and speeds of 4.000-8.000-16.000-40.000 revolutions per minute (rpm) were tested. Temperature differences of drilling parameters were calculated by 1-way ANOVA, followed by Tukey’s HSD post hoc tests. Time differences and differences among “optimal” and “suboptimal” groups (with the cut-off value of 3°C and 3s) were estimated by Kruskal-Wallis test with pairwise comparisons. P<0.05 was considered significant. Results. The highest mean temperatures with new and worn drills were 4.64±0.53°C and 6.89±1.16°C, while drilling times varied between 0.16±0.02s and 22.77±5.45s. A 3°C and 3s cut-off value classified drillings significantly to (1) optimal [3N and 8000-16000-40000 rpm or 10N and 4000-8000-16000-40000 rpm] or suboptimal due to (2) high temperatures or (3) long preparation times. Using worn drills, the following parameters should be avoided: 3N with 4.000-8.000 rpm, 10N with 40000 rpm, and 25N at any revolutions. Discussion. The study extensively mapped the drilling temperatures and preparation times of tungsten carbide round drills. Temperatures did not exceed 10°C during drillings with maximal amount of cooling, as well as the drilling parameters, which kept temperatures and preparation times in the most optimal range which were clearly established

Influence of TEGDMA monomer on MMP-2, MMP-8, and MMP-9 production and collagenase activity in pulp cells

Resin-based composites may leach monomers such as triethylene-glycol dimethacrylate (TEGDMA), which could contribute to intrapulpal inflammation. The aim of this investigation was to examine whether various concentrations of TEGDMA are able to influence dentally relevant Matrix metalloproteinase (MMP)-2, MMP-8, and MMP-9 production, total collagenase/gelatinase activity in pulp cells, and suggest possible signaling mechanisms.Pulp cells were cultured, followed by a 1-day exposure to sublethal TEGDMA concentrations (0.1, 0.2, and 0.75 mM). Total MMP activity was measured by an EnzCheck total collagenase/gelatinase assay, while the production of specific MMPs and the relative changes of phosphorylated, i.e., activated signaling protein levels of extracellular signal-regulated kinase (ERK)1/2, p38, c-Jun N-terminal kinase (JNK) were identified by western blot. Immunocytochemistry image data was also plotted and analyzed to see whether TEGDMA could possibly alter MMP production.An increase in activated MMP-2, MMP-8, and MMP-9 production as well as total collagenase activity was seen after a 24-h exposure to the abovementioned TEGDMA concentrations. Increase was most substantial at 0.1 (P = 0.002) and 0.2 mM (P = 0.0381). Concurrent p-ERK, p-p38, and p-JNK elevations were also detected.Results suggest that monomers such as TEGDMA, leached from resin-based restorative materials, activate and induce the production of dentally relevant MMPs in pulp cells. Activation of ERK1/2, p38, or JNK and MMP increase may play a role in and/or can be part of a broader stress response. Clinical relevance Induction of MMP production and activity may further be components in the mechanisms of intrapulpal monomer toxicity

Intrapulpal temperature changes during the cementation of ceramic veneers

Adhesive cementation of ceramic veneers may increase pulpal temperature (PT) due to the combined efect of heat generated by the curing unit and the exothermic reaction of the luting agent (LA). PT increase may induce pulpal damage. The aim was to determine the PT rise during the luting of ceramic veneers (CV) of diferent thicknesses with light- or dual-curing (LC, DC) adhesive cements as well as pre-heated restorative resin-based composites (PH-RBC). For this a thermocouple sensor was positioned in the pulp chamber of a prepared maxillary central incisor. LC, DC adhesive cements and PH-RBCs heated to 55 °C were used for the luting of CVs of 0.3, 0.5, 0.7, and 1.0 mm thicknesses. The exothermic reaction of LAs added signifcantly to the thermal efect of the curing unit. PT change ranged between 8.12 and 14.4 °C with the investigated combinations of LAs and ceramic thicknesses (p≤ 0.01). The increase was inversely proportional to the increasing CV thicknesses. The highest rise (p≤ 0.01) was seen with the polymerization of PH-RBCs. Temperature changes were predominantly infuenced by the composition of the LA, which was followed by CV thickness

TEGDMA (triethylene-glycol-dimethacrylate) induces both caspase-dependent and caspase-independent apoptotic pathways in pulp cells

Monomers leached from resin-based composites (RBCs) may reach intrapulpal concentrations of the millimolar (mM) range, which could contribute to inflammation. The aim of this investigation was to assess the cytotoxicity of triethylene glycol dimethacrylate (TEGDMA) monomers on pulp cells as well as to identify molecular mechanisms leading to apoptosis. Pulp cells were harvested from molars extracted for orthodontic reasons and cultured through an explant method. To assess cytotoxicity, cells underwent a 5-day exposure to 0.75, 1.5, and 3 mM TEGDMA and were subject to cell counting and WST-1 staining. Based on the findings, cells were subsequently exposed to 0.1, 0.2, 0.75, 1.5, and 3 mM TEGDMA for 24 h to uncover the details of apoptosis. Changes in the production or cleavage of the apoptosis-specific proteins caspase-8, caspase-9, caspase-3, caspase-12, and Apoptosis-Inducing Factor (AIF) were measured by Western blot. The 5-day study showed concentration- and time-dependent cytotoxicity. Significant cell death was detected after 24 h with TEGDMA concentrations of 1.5 and 3 mM. One-day exposure to TEGDMA led to the activation of caspase-8, -9, -3, and -12 and an increased AIF production. Results suggest that relevant concentrations of TEGDMA monomers, leached from RBCs, induce apoptosis in pulp cells through both caspase-dependent as well as caspase-independent mechanisms. Endoplasmic reticulum stress and the activation of caspase-independent apoptotic pathways may be further mechanisms by which monomers induce apoptosis in pulp cells

Effect of Air-Polishing and Different Post-Polishing Methods on Surface Roughness of Nanofill and Microhybrid Resin Composites

Air-abrasion is a popular prophylactic procedure to maintain oral hygiene. However, depending on the applied air-abrasive powder, it can damage the surface of the tooth and restorations, making it susceptible to plaque accumulation. The purpose of this study was to investigate the effect of 5 s and 10 s air-abrasion of calcium carbonate on surface roughness (Ra) of enamel, nanofill, and microhybrid resin-composites and the effect of post-polishing with two-step rubber- (RP) or one-step brush polisher (BP) to re-establish the surface smoothness. Surface topography was visualized by scanning-electron-microscopy. The quantitative measurement of the Ra was carried out with atomic-force-microscopy. Air-abrasion for 10 s decreased the Ra of enamel as a result of abrasion of the natural surface texture. Post-polishing with RP after 10 s air-abrasion did not change the Ra or BP; however, Ra was increased significantly by scratching the surface. Air-abrasion increased the Ra of resin composites significantly, irrespective of the application time. While RP provided a similarly smooth surface to the control in the case of microhybrid resin composite, BP increased the Ra significantly. The Ra for the control group of the nanofill-resin composite was initially high, which was further increased by air-abrasion. RP and BP re-established the initial Ra with deeper and shallower scratches after BP. Both the material and treatment type showed a large effect on Ra

Pre-Heating Effect on Monomer Elution and Degree of Conversion of Contemporary and Thermoviscous Bulk-Fill Resin-Based Dental Composites

Detection of unreacted monomers from pre-heated resin-based dental composites (RBC) is not a well-investigated topic so far. The objectives were to determine the temperature changes during the application and polymerization, the degree of conversion (DC) and unreacted monomer elution of room temperature (RT), and pre-heated thermoviscous [VisCalor Bulk(VCB)] and high-viscosity full-body contemporary [Filtek One Bulk(FOB)] bulk-fill RBCs. The RBCs' temperatures during the sample preparation were recorded with a K-type thermocouple. The DC at the top and bottom was measured with micro-Raman spectroscopy and the amounts of eluted BisGMA, UDMA, DDMA, and TEGDMA were assessed with High-Performance Liquid Chromatography. The temperatures of the pre-heated RBCs decreased rapidly during the manipulation phase. The temperature rise during photopolymerization reflects the bottom DCs. The differences in DC% between the top and the bottom were significant. RT VCB had a lower DC% compared to FOB. Pre-heating did not influence the DC, except on the bottom surface of FOB where a significant decrease was measured. Pre-heating significantly decreased the elution of BisGMA, UDMA, DDMA in the case of FOB, meanwhile, it had no effect on monomer release from VCB, except TEGDMA, which elution was decreased. In comparison, RBC composition had a stronger influence on DC and monomer elution, than pre-cure temperature