12 research outputs found
Comparison of Combustion Dynamic Characteristics of Two Advanced Multi-Cup Fuel Injectors
An experimental investigation of the combustion dynamic characteristics of two advanced multi-cup lean direct injectors (LDI) under simulated gas turbine combustor conditions was conducted. The objective was to gain a better understanding of the physical phenomena inside a pressurized flame tube combustion chamber and study the effects of injector flow number on combustion dynamics. The injectors are known as Three-zone Injectors one and two or 3ZI-1 and 3ZI-2, respectively. The injectors were experimentally evaluated at inlet pressures up to 1.724 MPa, non-vitiated air temperatures up to 828K, and adiabatic flame temperatures up to 1975K. Dynamic pressure measurements were taken upstream of the injectors and in the combustion zone. The combustion dynamic behavior of the two injectors was measured over a range of inlet pressures, inlet temperatures, fuel air ratios, and fuel flow splits
Compliant Metal Enhanced Convection Cooled Reverse-Flow Annular Combustor
A joint Army/NASA program was conducted to design, fabricate, and test an advanced, reverse-flow, small gas turbine combustor using a compliant metal enhanced (CME) convection wall cooling concept. The objectives of this effort were to develop a design method (basic design data base and analysis) for the CME cooling technique and tben demonstrate its application to an advanced cycle, small, reverse-flow combustor with 3000 F (1922 K) burner outlet temperature (BOT). The CME concept offers significant improvements in wall cooling effectiveness resulting in a large reduction in cooling air requirements. Therefore, more air is available for control of burner outlet temperature pattern in addition to the benefit of improved efficiency, reduced emissions, and smoke levels. Rig test results demonstrated the benefits and viability of the CME concept meeting or exceeding the aerothermal performance and liner wall temperature characteristics of similar lower temperature-rise combustors, achieving 0.15 pattern factor at 3000 F (1922 K) BOT, while utilizing approximately 80 percent less cooling air than conventional, film-cooled combustion systems
Experimental Combustion Dynamics Behavior of a Multi-Element Lean Direct Injection (LDI) Gas Turbine Combustor
An experimental investigation of the combustion dynamic characteristics of a research multi-element lean direct injection (LDI) combustor under simulated gas turbine conditions was conducted. The objective was to gain a better understanding of the physical phenomena inside a pressurized flametube combustion chamber under acoustically isolated conditions. A nine-point swirl venturi lean direct injection (SV-LDI) geometry was evaluated at inlet pressures up to 2,413 kPa and non-vitiated air temperatures up to 867 K. The equivalence ratio was varied to obtain adiabatic flame temperatures between 1388 K and 1905 K. Dynamic pressure measurements were taken upstream of the SV-LDI, in the combustion zone and downstream of the exit nozzle. The measurements showed that combustion dynamics were fairly small when the fuel was distributed uniformly and mostly due to fluid dynamics effects. Dynamic pressure fluctuations larger than 40 kPa at low frequencies were measured at 653 K inlet temperature and 1117 kPa inlet pressure when fuel was shifted and the pilot fuel injector equivalence ratio was increased to 0.72
Thermochemistry of Calcium-Magnesium-Aluminum-Silicate (CMAS) and Components of Advanced Thermal and Environmental Barrier Coating Systems
There is increasing interest in the degradation mechanism studies of thermal and environmental barrier coatings (TEBCs) of gas turbines by molten CaO-MgO-Al(exp. 2)O(exp. 3)-SiO(exp. 2) CMAS). CMAS minerals are usually referred as silicon-containing sand dust and volcano ash materials that are carried by the intake air into gas turbines, e.g. in aircraft engines, and their deposits often react at high temperatures (greater than 1200 degrees C) with the engine turbine coating systems and components. The high temperature reactions causes degradation and accelerated failure of the static and rotating components of the turbine engines. We discuss some results of the reactions between the CMAS and Rare-Earth (RE = Y, Yb, Dy, Gd, Nd and Sm) - oxide stabilized ZrO(exp. 2) or HfO(exp. 2) systems, and the stability of the resulting oxides and silicates. Plasma sprayed hollow tube samples (outside diameter = 4.7 mm, wall thickness = 0.76 mm and = 26 mm height) were half filled with CMAS powder, wrapped and sealed with platinum foil, and heat treated at 1310 degrees C for 5h. Samples were characterized by differential scanning calorimetry (DSC), X-ray diffraction, and cross-section electron microscopy analysis and energy dispersive X-ray spectroscopy. It was found that CMAS penetrated the samples at the grain boundaries and dissolved the TEBC materials to form silicate phases containing the rare-earth elements. Furthermore, it was found that apatite crystalline phases were formed in the samples with total rare-earth content higher than 12 mol% in the reaction zone for the ZrO(exp. 2) system. In general, samples with the nominal compositions (30YSZ), HfO(exp. 2)-7Dy(exp. 2)O(exp. 2) and ZrO(exp. 2)-9.5Y(exp. 2)O(exp. 3)-2.25Gd(exp. 2)O(exp. 3)-2.25Yb(exp. 2)O(exp. 3) exhibited lower reactivity or more resistance to CMAS than the other coating compositions of this work
Characterization and Antiproliferative Activity of Nobiletin-Loaded Chitosan Nanoparticles
Nobiletin is a polymethoxyflavonoid with a remarkable antiproliferative effect. In order to overcome its low aqueous solubility and chemical instability, the use of nanoparticles as carriers has been proposed. This study explores the possibility of binding nobiletin to chitosan nanoparticles, as well as to evaluate their antiproliferative activity. The association and loading efficiencies are 69.1% and 7.0%, respectively. The formation of an imine bond between chitosan amine groups and the carbonyl group of nobiletin, via Schiff-base, is proposed. Nobiletin-loaded chitosan nanoparticles exhibit considerable inhibition (IC50=8 μg/mL) of cancerous cells, revealing their great potential for applications in cancer chemotherapy
América Latina piensa América Latina
América Latina piensa América Latina es el resultado de un esfuerzo colectivo de un conjunto de investigadores cuyo objetivo común es propiciar el desarrollo de un pensamiento nuestro, que articule teoría
y praxis, pasado y presente, y que se asiente en la afirmación de la integración de la región. Este proceso exige, a nuestro juicio, retomar la senda marcada por el pensamiento social crítico latinoamericano de
los años sesenta y setenta pero evitando caer en una mirada nostálgica que sentencie que todo pasado fue mejor.
La revitalización del pensamiento social latinoamericano es una contribución a repensar el desarrollo de las ciencias sociales y la filosofía, pero sobre todo es un aporte a la reflexión sobre los procesos
de transformación de América Latina hoy. En la actualidad, quienes pensamos América Latina nos encontramos frente a una realidad que plantea desafíos teóricos y prácticos. El libro invita a construir herramientas
analíticas capaces de afrontar estos desafíos
Recommended from our members
Risk factors and predictors of intracranial hemorrhage after mechanical thrombectomy in acute ischemic stroke: insights from the Stroke Thrombectomy and Aneurysm Registry (STAR)
BackgroundReducing intracranial hemorrhage (ICH) can improve patient outcome in acute ischemic stroke (AIS) intervention. We sought to identify ICH risk factors after AIS thrombectomy.MethodsThis is a retrospective review of the Stroke Thrombectomy and Aneurysm Registry (STAR) database. All patients who underwent AIS thrombectomy with available ICH data were included. Multivariable regression models were developed to identify predictors of ICH after thrombectomy. Subgroup analyses were performed stratified by symptom status and European Cooperative Acute Stroke Study (ECASS) grade.ResultsThe study cohort comprised 6860 patients. Any ICH and symptomatic ICH (sICH) occurred in 25% and 7% of patients, respectively. Hemorrhagic infarction 1 (HI1) occurred in 36%, HI2 in 24%, parenchymal hemorrhage 1 (PH1) in 22%, and PH2 in 17% of patients classified by ECASS grade. Intraprocedural complications independently predicted any ICH (OR 3.8083, P<0.0001), PH1 (OR 1.9053, P=0.0195), and PH2 (OR 2.7347, P=0.0004). Race also independently predicted any ICH (black: OR 0.5180, P=0.0017; Hispanic: OR 0.4615, P=0.0148), sICH (non-white: OR 0.4349, P=0.0107), PH1 (non-white: OR 3.1668, P<0.0001), and PH2 (non-white: OR 1.8689, P=0.0176), with white as the reference. Primary mechanical thrombectomy technique also independently predicted ICH. ADAPT (A Direct Aspiration First Pass Technique) was a negative predictor of sICH (OR 0.2501, P<0.0001), with stent retriever as the reference.ConclusionsThis study identified ICH risk factors after AIS thrombectomy using real-world data. There was a propensity towards a reduced sICH risk with direct aspiration. Procedural complications and ethnicity were predictors congruent between categories of any ICH, sICH, PH1, and PH2. Further investigation of technique and ethnicity effects on ICH and outcomes after AIS thrombectomy is warranted