Exploring amide linkage in a polyviologen derivative towards simultaneous voltammetric determination of Pb(II), Cu(II) and Hg(II) ions

In this study, we report reductive electrosynthesis of a polyviologen derivative bearing amide linkage in its side chain, derived from a cyanopyridinium based monomer with amide functionality. The as grown film was characterized by cyclic voltammetry which displays a well-defined and reversible two step redox response characteristic of viologen. FTIR analysis show evidence of amide linkage and successful reduction of cyanopyridinium moieties to polyviologen. In situ multi ESR/UV-Vis-NIR spectroelectrochemistry show a single line in ESR signal, thereby suggesting polarons as the only charge carrier involved during charging/discharging process. Furthermore, a characteristic UV&ndash;Vis absorption spectra confirms viologen formation. Finally, the polyviologen film is subjected to simultaneous voltammetric determination of heavy metal ions, Pb(II), Cu(II) and Hg(II). The amide linkage in the polyviologen derivative is supposedly complexing these divalent metal ions, enabling their sensitive and simultaneous determination with low detection limits.</div

J-like aggregation of a cationic polythiophene with hydrogen-bonding capabilities due to 1,4-dioxane: Solution excitation spectra and fluorescence, morphology and surface free energy of films

This work presents solution- and solid-state evidence of the enhancement of J-like aggregation of a cationic polythiophene (CPT) with isothiouronium functionalities (PT1), caused by a decrease in the polarity and hydrogen-bonding (H-bonding) capacity of the solvent, generated by using a 50:50 v/v 1,4-dioxane-water mixture (W-DI) instead of water. In solution, the presence of 1,4-dioxane (DI) seems to generate selective solvation, tuning the energy transfer within PT1 from inter-chain into intra-chain, enhancing J-like aggregation. On the other hand, during the casting process, the presence of DI directs the interaction with solid-substrates, generating an increase in the solid-state fluorescence, modifying the morphology from one similar to ballistic-aggregation (BA) into one similar to attachment limited aggregation (ALA), DI also modifies the SFE by increasing slightly its polar contribution (γSp) and decreasing the dispersive one (γSd). These results can be explained to be caused by a "coating" effect in presence of DI (as proposed before experimentally and computationally). Our results show a clear correlation between the solution- and solid-state properties of PT1 in each solvent, further validating the use of the fluorescence excitation spectra to trace J-like aggregation of water-soluble conjugated polymeric fluorophores in solution. This information could be useful for predicting and designing specific mesoscopic architectures of CPTs (and conjugated polyelectrolytes in general), which are molecules lacking of clear structure-function guidelines for designing high-performance polythiophene-based interlayer materials, especially for CPTs (and conjugated polyelectrolytes (CPEs) in general), particularly those with H-bonding capabilities. To the best of our knowledge the use of solution-state fluorescence excitation spectra to identify J-like aggregation of water-soluble conjugated polymers (CPs) has been scarcely used/discussed in literature and no correlation with solid-state properties was reported previously

Cationic Imidazolium Polythiophenes: Effects of Imidazolium-Methylation on Solution Concentration-Driven Aggregation and Surface Free Energy of Films Processed from Solvents with Different Polarity

Cationic imidazolium-functionalized polythiophenes with single- or double-methylation of the imidazolium ring were used to study the impact of imidazolium-methylation on (i) the solution concentration-driven aggregation in the presence of paramagnetic probes with different ionic and hydrophobic constituents and (ii) their surface free energy (SFE) as spin-coated films deposited on plasma-activated glass. Electron paramagnetic resonance spectroscopy shows that the differences in film structuration between the polymers with different methylations originate from the early stages of aggregation. In the solid state, higher degree of imidazolium-methylation generates smaller values of total SFE, gamma S, (by around 2 mN/m), which could be relevant in optoelectronic applications. Methylation also causes a decrease in the polar contribution of gamma S (gamma Sp), suggesting that methylation decreases the polar nature of the imidazolium ring, probably due to the blocking of its H-bonding capabilities. The values of gamma S obtained in the present work are similar to the values obtained for doped films of neutral conjugated polymers, such as polyaniline, poly(3-hexylthiophene), and polypyrrole. However, imidazolium-polythiophenes generate films with a larger predominance of the dispersive component of gamma S (gamma Sd), probably due to the motion restriction in the ionic functionalities in a conjugated polyelectrolyte, in comparison to regular dopants. The presence of 1,4-dioxane increases gamma Sp, especially, in the polymer with larger imidazolium-methylation (and therefore unable to interact through H-bonding), probably by a decrease of the imidazolium-glass interactions. Singly-methylated imidazolium polythiophenes have been applied as electrode selective ("buffer") interlayers in conventional and inverted organic solar cells, improving their performance. However, clear structure-function guidelines are still needed for designing high-performance polythiophene-based interlayer materials. Therefore, the information reported in this work could be useful for such applications

Titania and titania-silica coatings for titanium: comparison of ectopic bone formation within cell-seeded scaffolds.

Contains fulltext : 52660.pdf (publisher's version ) (Open Access)The aim of this study was to compare titania (TiO(2))-coated, titania-silica (TiSi)-coated, and uncoated (cpTi) titanium fiber meshes as scaffolds for bone engineering. The scaffolds were loaded with bone marrow stromal cells and implanted subcutaneously in rats. Ectopic bone formation after 1, 4, and 12 weeks of implantation was evaluated using histology and histomorphometry. After 1 week of implantation, multiple patches of unorganized mineralizing tissue were seen in all implants. The amount of this bone-like tissue clearly increased from 1 to 4 weeks. Bone apposition occurred in direct contact with coated meshes, while a thin layer of unmineralized fibrous tissue was often observed surrounding cpTi mesh fibers. After 12 weeks, the structure of bone, with bone marrow-like tissue, was further matured and mesh fibers were embedded in lamellar bone. No statistical differences in the amount of mineralized bone were observed between scaffold types at any point of time. Only TiSi scaffolds showed further increase in bone area from 4 to 12 weeks (p < 0.01). A notable difference was that the sol-gel coatings resulted in enhanced initial bone contact and distribution of bone tissue, whereas uncoated implants showed bone formation mainly in the center of the scaffolds. In conclusion, TiO(2)-based sol-gel coatings may be used in tissue engineering to gain more uniform distribution of bone throughout titanium fiber mesh scaffolds

Enhancement of charge-assisted hydrogen bond capabilities due to O-alkylation proximity in alkoxy cationic polythiophenes: solution- and solid-state evidence via EPR, AFM and surface free energy

: Despite the array of applications for cationic polythiophenes (CPTs), there is still a need for structure-function guidelines and mechanistic understanding of their solution- and solid-state properties. This work presents a solution- and solid-state investigation of the effect of O-alkylation proximity on the hydrogen bonding (H-bonding) capabilities of alkoxy-CPTs, based on comparing an imidazolium alkoxy CPT with strong cation-pi, pi+ and positive charge-assisted hydrogen bonding (+CAHB) capabilities (PIMa), with two isothiouronium alkoxy CPTs with two-point +CAHB capabilities (PT1 & PT2), which have short and long alkoxy side chains, respectively. Our results show that a closer proximity of O-alkylation strengthens the +CAHB capabilities of PT1: in aqueous solutions, PT2 aggregates have a stronger interaction with cationic EPR spin probes than aggregates of PIMa and PT1, which in turn show a similar extent of repulsion towards the cationic spin probes. In solid-state, atomic force microscopy (AFM) shows that PIMa generates dendritic structures onto mica, with features of diffusion-limited aggregation (DLA), indicating strong interactions with the anionic substrate due to a high configurational entropy during spreading, regardless of being drop-casted from water or 1,4-dioxane-water (W-DI), despite the latter disturbing H-bonding due to selective solvation. PT1 is also capable of generating dendritic structures resembling ballistic aggregation (BA). However, this occurs only when casting from water, since W-DI generates island-like aggregates resembling attachment limited aggregation (ALA), which is the morphology generated by PT2 regardless of the solvent. Finally, spin-coated films of PIMa and PT1 show similar dispersivity of the surface free energy (SFE), which in turn is larger than that in PT2 films, which are also more affected when casted from W-DI, presenting much larger decreases of dispersivity. These results constitute a novel empirical structure-function guideline that could be useful for optimal design and/or processing of alkoxy CPTs. For example, dendritic patterns have recently gained attention since the colloidal droplet drying is related to engineering applications including inkjet printing, biosensing, and functional material design, while the SFE is relevant for opto- and bio-electronic applications of conjugated polyelectrolytes (CPEs). This information could also be useful when analyzing previous results obtained from alkoxy CPTs with different side chain lengths

Cationic Imidazolium Polythiophenes: Effects of Imidazolium-Methylation on Solution Concentration-Driven Aggregation and Surface Free Energy of Films Processed from Solvents with Different Polarity

Cationic imidazolium-functionalized polythiophenes with single- or double-methylation of the imidazolium ring were used to study the impact of imidazolium-methylation on (i) the solution concentration-driven aggregation in the presence of paramagnetic probes with different ionic and hydrophobic constituents and (ii) their surface free energy (SFE) as spin-coated films deposited on plasma-activated glass. Electron paramagnetic resonance spectroscopy shows that the differences in film structuration between the polymers with different methylations originate from the early stages of aggregation. In the solid state, higher degree of imidazolium-methylation generates smaller values of total SFE, γ S , (by around 2 mN/m), which could be relevant in optoelectronic applications. Methylation also causes a decrease in the polar contribution of γ S (γS p ), suggesting that methylation decreases the polar nature of the imidazolium ring, probably due to the blocking of its H-bonding capabilities. The values of γ S obtained in the present work are similar to the values obtained for doped films of neutral conjugated polymers, such as polyaniline, poly(3-hexylthiophene), and polypyrrole. However, imidazolium-polythiophenes generate films with a larger predominance of the dispersive component of γ S (γS d ), probably due to the motion restriction in the ionic functionalities in a conjugated polyelectrolyte, in comparison to regular dopants. The presence of 1,4-dioxane increases γS p , especially, in the polymer with larger imidazolium-methylation (and therefore unable to interact through H-bonding), probably by a decrease of the imidazolium-glass interactions. Singly-methylated imidazolium polythiophenes have been applied as electrode selective ("buffer") interlayers in conventional and inverted organic solar cells, improving their performance. However, clear structure-function guidelines are still needed for designing high-performance polythiophene-based interlayer materials. Therefore, the information reported in this work could be useful for such applications