The design of a two-element radio interferometer using satellite TV equipment

This research presents the design of a two-element radio interferometer capable of performing complex correlation. With the development of sophisticated radio astronomy instruments, particularly in South Africa, there is a need to develop an affordable educational instrument which can be used to demonstrate the fundamental concepts of radio interferometry to university students. The mass production of satellite TV equipment has resulted in relatively sensitive radio frequency (RF) equipment such as parabolic reflector dishes and low-noise block down-converters (LNBs) being available at significantly reduced costs. This served as the front-end of the interferometer which was used to observe the sun between 10.70 GHz - 12.75 GHz (RF). The LNB then down-converted these to an intermediate frequency (IF) between 0.95 GHz - 2.15 GHz. The LNBs were modified to make use of a common 25 MHz reference, which ensured that the observed fringes were only as a result of the source's geometric time delay. A power detector was also designed since the adding interferometer architecture was chosen. This power detector included the Analog Devices LT 5534 power detector integrated circuit (IC) and a Teensy 3.6 microcontroller. The calibrated power detector could detect signals as weak as - 60 dBm and showed less than 21 mV error in output for input signals in the range [- 50 dBm, -30 dBm]. The modified LNBs experienced issues, in particular the presence of a spurious LO signal, which distorted initial observations of the sun. This was resolved by the design and manufacture of narrowband hairpin filters and quarterwavelength stub filters which were used to isolate the IF band between 1.05 GHz - 1.15 GHz (corresponding RF between 10.80 GHz - 10.90 GHz). This also improved the interferometer's resolution. A series of filter-integrated Wilkinson power dividers and branchline couplers were designed to filter and further separate signals into in-phase and quadrature-phase (I-Q) components - these were required for complex correlation. The integrated quarter-wavelength stub filter and Wilkinson power divider achieved a maximum amplitude imbalance of 0.13 dB and phase imbalance of 0.9◦ between output ports. The integrated quarter-wavelength stub filter and branchline coupler achieved a maximum amplitude imbalance of 0.13 dB and phase imbalance of 91.1◦ between output ports. These results closely agreed with the simulated performance. First light was observed on the 5th December 2020 when the sun was successfully detected using the coherent two-element interferometer along a 1.1 m baseline. Other tests included using the observed fringe phase to verify the physical baseline. A theoretical baseline of 1.11 m was calculated for a physical baseline of 1.3 m indicating an error of less than 0.2 m. The sun's fringe frequency and amplitude was also observed for varying baselines - the sun was resolved along a 3 m baseline. Finally, full-system observations of the sun were conducted. These included observing the sun's cosine and sine fringes, which indicated that the analogue complex correlator was operating correctly. Thus, the primary goal of this project had been fulfilled. Specifically, developing a low-cost, educational two-element radio interferometer capable of detecting the sun

Direct GMSK modulation at microwave frequencies

Congestion in the radio spectrum is forcing emerging high rate wireless communication systems into upper microwave and millimeterwave frequency bands, where transceiver hardware architectures are less mature. One way to realize a simple and elegant hardware solution for a microwave transmitter is to exploit the advantages of directly modulating the phase of the carrier signal. A modulation method requiring continuous phase control of the carrier signal over the full 360 degree range is Gaussian Minimum Shift Keying (GMSK). Unfortunately, it is very difficult to design a microwave circuit to provide linear phase control of a carrier signal over the full 360 degree range using traditional methods. A novel method of obtaining continuous, linear phase modulation of a microwave carrier signal over the full 360 degree range is proposed. This method is based on controlling a phase shifter, at a subharmonic of the desired output carrier frequency, and then using a frequency multiplier to obtain the desired output frequency. The phase shifter is designed to be highly linear over a fraction of the full 360 range. The frequency multiplier is a nonlinear circuit that shifts the frequency by *'N'. The subtle part of this nonlinear operation is that the multiplier also multiplies the instantaneous phase of the phase shifter output signal by *'N', thus expanding the linear phase shift range to the required 360 degrees. Using this nonlinear frequency multiplication principle, the modulator can readily be extended into the millimeterwave region. A prototype circuit is designed and performance results are presented for this method of carrier phase modulation at 18 GHz. The prototype circuit is realized with very simple hardware, containing only a single microwave active device. An extension to the modulator involving phase locking or injection locking of a power oscillator is also suggested for obtaining higher power modulated output signals. In addition to direct continuous phase modulation, the proposed method is also suitable for a wide variety of transceiver applications, including phase synchronization of antenna and oscillator arrays, phased array antenna beam steering, indirect frequency modulation, and ultra-small carrier frequency translation

Dynamic Optical Networks for Data Centres and Media Production

This thesis explores all-optical networks for data centres, with a particular focus on network designs for live media production. A design for an all-optical data centre network is presented, with experimental verification of the feasibility of the network data plane. The design uses fast tunable (< 200 ns) lasers and coherent receivers across a passive optical star coupler core, forming a network capable of reaching over 1000 nodes. Experimental transmission of 25 Gb/s data across the network core, with combined wavelength switching and time division multiplexing (WS-TDM), is demonstrated. Enhancements to laser tuning time via current pre-emphasis are discussed, including experimental demonstration of fast wavelength switching (< 35 ns) of a single laser between all combinations of 96 wavelengths spaced at 50 GHz over a range wider than the optical C-band. Methods of increasing the overall network throughput by using a higher complexity modulation format are also described, along with designs for line codes to enable pulse amplitude modulation across the WS-TDM network core. The construction of an optical star coupler network core is investigated, by evaluating methods of constructing large star couplers from smaller optical coupler components. By using optical circuit switches to rearrange star coupler connectivity, the network can be partitioned, creating independent reserves of bandwidth and resulting in increased overall network throughput. Several topologies for constructing a star from optical couplers are compared, and algorithms for optimum construction methods are presented. All of the designs target strict criteria for the flexible and dynamic creation of multicast groups, which will enable future live media production workflows in data centres. The data throughput performance of the network designs is simulated under synthetic and practical media production traffic scenarios, showing improved throughput when reconfigurable star couplers are used compared to a single large star. An energy consumption evaluation shows reduced network power consumption compared to incumbent and other proposed data centre network technologies

Application of advanced on-board processing concepts to future satellite communications systems

An initial definition of on-board processing requirements for an advanced satellite communications system to service domestic markets in the 1990's is presented. An exemplar system architecture with both RF on-board switching and demodulation/remodulation baseband processing was used to identify important issues related to system implementation, cost, and technology development

High Efficiency Design Techniques for Linear Power Amplifiers

abstract: This thesis describes the design process used in the creation of a two stage cellular power amplifier. A background for understanding amplifier linearity, device properties, and ACLR estimation is provided. An outline of the design goals is given with a focus on linearity with high efficiency. The full design is broken into smaller elements which are discussed in detail. The main contribution of this thesis is the description of a novel interstage matching network topology for increasing efficiency. Ultimately the full amplifier design is simulated and compared to the measured results and design goals. It was concluded that the design was successful, and used in a commercially available product.Dissertation/ThesisM.S. Electrical Engineering 201

Adaptive Suppression of Interfering Signals in Communication Systems

The growth in the number of wireless devices and applications underscores the need for characterizing and mitigating interference induced problems such as distortion and blocking. A typical interference scenario involves the detection of a small amplitude signal of interest (SOI) in the presence of a large amplitude interfering signal; it is desirable to attenuate the interfering signal while preserving the integrity of SOI and an appropriate dynamic range. If the frequency of the interfering signal varies or is unknown, an adaptive notch function must be applied in order to maintain adequate attenuation. This work explores the performance space of a phase cancellation technique used in implementing the desired notch function for communication systems in the 1-3 GHz frequency range. A system level model constructed with MATLAB and related simulation results assist in building the theoretical foundation for setting performance bounds on the implemented solution and deriving hardware specifications for the RF notch subsystem devices. Simulations and measurements are presented for a Low Noise Amplifer (LNA), voltage variable attenuators, bandpass filters and phase shifters. Ultimately, full system tests provide a measure of merit for this work as well as invaluable lessons learned. The emphasis of this project is the on-wafer LNA measurements, dependence of IC system performance on mismatches and overall system performance tests. Where possible, predictions are plotted alongside measured data. The reasonable match between the two validates system and component models and more than compensates for the painstaking modeling efforts. Most importantly, using the signal to interferer ratio (SIR) as a figure of merit, experimental results demonstrate up to 58 dB of SIR improvement. This number represents a remarkable advancement in interference rejection at RF or microwave frequencies

Millimeter-Wave MMICs and Applications

As device technology improves, interest in the millimeter-wave band grows. Wireless communication systems migrate to higher frequencies, millimeter-wave radars and passive sensors find new solid-state implementations that promise improved performance, and entirely new applications in the millimeter-wave band become feasible. The circuit or system designer is faced with a new and unique set of challenges and constraints to deal with in order to use this portion of the spectrum successfully. In particular, the advantages of monolithic integration become increasingly important. This thesis presents many new developments in Monolithic Millimeter-Wave Integrated Circuits (MMICs), both the chips themselves and systems that use them. It begins with an overview of the various applications of millimeter waves, including a discussion of specific projects that the author is involved in and why many of them demand a MMIC implementation. In the subsequent chapters, new MMIC chips are described in detail, as is the role they play in real-world projects. Multi-chip modules are also presented with specific attention given to the practical details of MMIC packaging and multi-chip integration. The thesis concludes with a summary of the works presented thus far and their overall impact on the field of millimeter-wave engineering.</p

High-Performance On-Chip Microwave Photonic Signal Processing Using Linear and Nonlinear Optics

Manipulating and processing radio-frequency (RF) signals using integrated photonic devices has recently emerged as a paradigm-shifting technology for future microwave applications. This emerging technique is referred to as integrated microwave photonics (IMWP) which enables the high-frequency processing and unprecedentedly wideband tunability in compact photonic circuits, with significantly enhanced stability and robustness. However, to find widespread applications, the performance of IMWP devices must meet or exceed the achievable performance of conventional electronic counterparts. The work presented in this thesis investigates high-performance IMWP signal processing from two aspects: the optimized IMWP processing schemes and the photonic integration. Firstly, we explore novel schemes to improve the performance of chip-based microwave photonic subsystems, such as RF delay lines and RF filters which are basic building blocks of RF systems. A phase amplification technique is demonstrated to achieve a Si3N4 chip-based RF time delay with a delay tuning speed at gigahertz level. A new scheme to achieve an all-optimized RF photonic notch filter is demonstrated, producing a record-high RF link performance and complete functionalities. To unlock the potential of RF signal processing, we investigate a new filter concept of pairing linear and nonlinear optics for a high-performance RF photonic filter. To reduce the footprint of the novel IMWP filter, the photonic integration of both the ring resonators and Brillouin-active circuits on the same photonic chip is achieved. To eliminate the use of integrated optical circulators for on-chip SBS, on-chip backward inter-modal stimulated Brillouin scattering is predicted and experimentally demonstrated in a Si-Chalcogenide hybrid integrated photonic platform. The study and demonstrations presented in this thesis make the first viable step towards high-performance IMWP signal processing for real-world RF applications

Ultra-low power radio transceiver for wireless sensor networks

The objective of this thesis is to present the design and implementation of ultra-low power radio transceivers at microwave frequencies, which are applicable to wireless sensor network (WSN) and, in particular, to the requirement of the Speckled Computing Consortium (or SpeckNet). This was achieved through quasi-MMIC prototypes and monolithic microwave integrated circuit (MMIC) with dc power consumption of less than 1mW and radio communication ranges operating at least one metre. A wireless sensor network is made up of widely distributed autonomous devices incorporating sensors to cooperatively monitor physical environments. There are different kinds of sensor network applications in which sensors perform a wide range of activities. Among these, a certain set of applications require that sensor nodes collect information about the physical environment. Each sensor node operates autonomously without a central node of control. However, there are many implementation challenges associated with sensor nodes. These nodes must consume extremely low power and must communicate with their neighbours at bit-rates in the order of hundreds of kilobits per second and potentially need to operate at high volumetric densities. Since the power constraint is the most challenging requirement, the radio transceiver must consume ultra-low power in order to prolong the limited battery capacity of a node. The radio transceiver must also be compact, less than 5×5 mm2, to achieve a target size for sensor node and operate over a range of at least one metre to allow communication between widely deployed nodes. Different transceiver topologies are discussed to choose the radio transceiver architecture with specifications that are required in this project. The conventional heterodyne and homodyne topologies are discussed to be unsuitable methods to achieve low power transceiver due to power hungry circuits and their high complexity. The super-regenerative transceiver is also discussed to be unsuitable method because it has a drawback of inherent frequency instability and its characteristics strongly depend on the performance of the super-regenerative oscillator. Instead, a more efficient method of modulation and demodulation such as on-off keying (OOK) is presented. Furthermore, design considerations are shown which can be used to achieve relatively large output voltages for small input powers using an OOK modulation system. This is important because transceiver does not require the use of additional circuits to increase gain or sensitivity and consequently it achieves lower power consumption in a sensor node. This thesis details the circuit design with both a commercial and in-house device technology with ultra-low dc power consumption while retaining adequate RF performance. It details the design of radio building blocks including amplifiers, oscillators, switches and detectors. Furthermore, the circuit integration is presented to achieve a compact transceiver and different circuit topologies to minimize dc power consumption are described. To achieve the sensitivity requirements of receiver, a detector design method with large output voltage is presented. The receiver is measured to have output voltages of 1mVp-p for input powers of -60dBm over a 1 metre operating range while consuming as much as 420μW. The first prototype combines all required blocks using an in-house GaAs MMIC process with commercial pseudomorphic high electron mobility transistor (PHEMT). The OOK radio transceiver successfully operates at the centre frequency of 10GHz for compact antenna and with ultra-low power consumption and shows an output power of -10.4dBm for the transmitter, an output voltage of 1mVp-p at an operating range of 1 metre for the receiver and a total power consumption of 840μW. Based on this prototype, an MMIC radio transceiver at the 24GHz band is also designed to further improve the performance and reduce the physical size with an advanced 50nm gate-length GaAs metamorphic high electron mobility transistor (MHEMT) device technology