2 research outputs found
Two Tunable Frequency Duplexer Architectures for Cellular Transceivers
In this paper two architectures for tunable duplexersare presented. The tuning is accomplished through variablecapacitance and resistance. The architectures are based on athree element series-parallel resonator, with one pass and onestop frequency. Both architectures rely on filtering as well ascancellation for good Tx to Rx isolation while maintaining lowinsertion loss. The first architecture, the Filtered TransformerBalanced (FTB) isolator, has single ended transmit and antennaports and a differential receive port. The second architecture,the Cross Coupled Filtering (CCF) isolator, is fully differential.For a resonator Q of 50, the impedance ratio of the resonator atpass and stop frequencies is 18.5dB for 3GPP band-I. In the FTBisolator this results in 1.65dB Tx and 2.14dB Rx insertion loss,and 53 dB isolation for a 20 MHz channel bandwidth. In the CCFisolator this results in 1.9dB Tx and 1.9dB Rx insertion loss, and59dB isolation for a 20 MHz channel bandwidth. These figuresare obtained with a 20% resistive mismatch, showing feasibility ofgood performance in an environment with changing impedance.As the operating frequencies of cellular systems increase, thesestructures will become fully integratable due to the reduced sizesof inductors and transformers
Методи побудови та схемотехнічні рішення мікросмужкових смуго-пропускних фільтрів
Літвінцев С. М. Методи побудови та схемотехнічні рішення мікросмужкових смуго-пропускних фільтрів. — Кваліфікаційна наукова праця на правах рукопису.
Дисертація на здобуття наукового ступеня кандидата технічних наук за
спеціальністю 05.12.13 «Радіотехнічні пристрої та засоби телекомунікацій» (17
— Електроніка та телекомунікації). — Національний технічний університет Ук-
раїни «Київський політехнічний інститут імені Ігоря Сікорського» МОН України, Київ, 2023.
У дисертації вирішено актуальну науково-технічну задачу розвитку методів побудови та нові схемотехнічні рішення для смуго-пропускних фільтрів
(СПФ), які використовуються в сучасних системах бездротового зв'язку.
У першому розділі здійснено розширення функціональних можливостей
матриці зв'язків шляхом її модифікації. Розглянуто приклади незастосовності матриці зв'язків, проведено аналіз резонатора прохідного типу, який є причиною
зазначеної незастосовності, вирішено задачу модифікації матриці зв'язків, яка
призводить до адекватних результатів розрахунку частотних характеристик і розширенню області застосувань матриці зв'язків.
Детальний розгляд прохідного резонатора, включеного у чотирьохполюсник, показав, що здійснювана ним конфігурація зв'язку залежить від його структури. Це використано для відповідної модифікації матриці зв'язку, щоб та достовірно відображала частотні характеристики. Модифікація полягає у зміні знаків
деяких елементів матриці зв'язків згідно зі встановленими в роботі правилами.
Встановлені в роботі правила модифікації матриці зв'язків наведені на чисельних
прикладах.
Для перевірки змін в матриці зв'язків виготовлено відповідні фільтри, виміряні характеристики яких підтвердили запропоновані зміни.
У другому розділі розглянуті СПФ із змішаними зв'язками між суміжними
резонаторами. Проведено аналіз закономірностей розташування нулів передачі
таких фільтрів, та взаємозв'язок між лінійною та звичайною формами подання
змішаного зв'язку. Запропоновано метод синтезу таких фільтрів, заснований на
використанні інвертора провідності для змішаного зв'язку.
На відміну від звичайного зв'язку, змішаний зв'язок характеризується
трьома, а не двома, характерними частотами: парною модою і непарною модою
пов'язаних коливань, а також значенням частоти нуля передачи. Ці частоти можна визначити при слабкому зв'язку резонаторів.
Оскільки змішаний коефіцієнт зв'язку у звичайній формі не може бути використаний в матриці зв'язків, тому для розрахунку частотних характеристик
СПФ необхідно мати іншу форму представлення. Для цього використана лінійна
форма подання коефіцієнт зв'язку на нормованій частоті. В такому випадку зявляється можливість використання матриці звязків для обрахунку параметрів
смуго-пропускного фільтру у випадку, коли в нього використано змішаний зв'язок.
В роботі запропоновано ефективний метод синтезу фільтрів зі змішаними
зв'язками між суміжними резонаторами. Метод базується на відомій техніці використання інверторів провідності, схеми яких тепер містять паралельні контури
відповідно до змішаних зв'язків резонаторів. Результати ЕМ моделювання підтвердили працездатність процедури синтезу фільтрів.
Встановлено взаємозв'язок між лінійною та звичайною формами представлення змішаного зв'язку. Вперше запропоновано метод аналітичного синтезу
СПФ зі змішаними зв'язками між суміжними резонаторами, заснований на використанні інверторів провідностей для змішаного зв'язку. При цьому досягнуто
рівень селективності фільтра, що відповідає більш складним структурам без
ускладнення конструкції фільтра.
У третьому розділі розглянуто фільтри з зосереджено-розподіленими зв'язками, широкою смугою загородження та підвищеною односторонньою вибірковістю. Запропоновано два методи збільшення смуги загородження в гребінчастих та решітчастих фільтрах.
Оскільки основу гребінчастих смуго-пропускних фільтрів складають зв'язані між собою чвертьхвильові резонатори, запропонований метод заснований на
закономірності зміни антирезонансних частот, пов'язаній зі зміною координати
підключення до чвертьхвильового резонатора.
Базуючись на виразі вхідної провідності чвертьхвильового резонатора,
визначено координати особових точок підключення до цього резонатора, використання яких призводить до придушення паразитних смуг пропускання в гребінчастому смуго-пропускному фільтрі. Окрім того зясовано, що використання однієї спеціальної координати підключення призводить до придушення не однієї, а
кількох періодично розташованих резонансних частот чвертьхвильового резонатора. Таким чином, якщо у одному фільтрі використати декілька особливих координат точок підключення, то в цьому випадку можливо досягти значного розширення смуги загородження в гребінчастому смуго-пропускному фільтрі.
Аналогічний метод розширення смуги загородження розлоблено для гребінчастого смуго-пропускного фільтру, який будується на основі напівхвильових
резонаторів. У випадку гребінчастого фільтру використання однієї точки підключення з особливою координатою також призводить до придушення не тільки
однієї паразитної резонансної частоти напівхвильового резонатора, а до одночасного придушення кількох періодично розташованих резонансних частот напівхвильового резонатора, закон розподілу яких також визначено і запропоновано
автором.
Оскільки сьогодні на ринку з'явилася велика кількість малогабарітних пасивних компонентів (ємності, індуктивності) з високою добротністю для використання в пристроях надвисоких частот, то одночасте використання мікросмужкових резонаторів і малогабаритних зосереджених елементів призводить до по-
яви нового виду звязків в смуго-пропускних фільтрах, який можна назвати зосереджено-розподіленим. Тому необхідні методи, за допомогою яких можна обраховувати значення всіх елементів, що входять у смуго-пропускний фільтр, що
побудований на основі таких зосереджено-розподілених зв'язках. Автором запропонована методика, яка дозволяє обрахувати значення всіх елементів, за допомогою яких побудовано смуго-пропускний фільтр з зосереджено-розподіленими зв'язками.
Таким чином, в даній роботі вирішена задача розширення смуги загородження в гребінчастих та решітчастих фільтрах за допомогою використання зосереджено-розподілених змішаних зв'язків між суміжними резонаторами, та нового методу розрахунку, заснованого на траєкторіях зміщення антирезонансних
частот використаних резонаторів.
Перевірка методу розширення смуги загородження по траєкторіях зміщення частот проведена по результатам вимірювання параметрів фільтра, створеного за запропонованим методом. Отримано розширення смуги загородження
більше ніж в три рази. Процес проектування представлено у вигляді алгоритму,
що уніфікує даний процес для розробника.
У четвертому розділі розглядається можливість розширення функціональних можливостей багатомодових резонаторів та фільтрів. Проведено аналіз двомодових планарних резонаторів з розімкненими та короткозамкнутими кінцями
на основі ступінчастих ліній, експериментально досліджено двомодові смугопропускні фільтри.
Існуючі двомодові резонатори на основі T-з'єднання обмежені функціонально, оскільки в них використовуються однорідні відрізки ліній. В роботі запропоновано замінити ці відрізки, відрізками ступінчастих ліній, та визначити потенційні можливості нових утворених двомодових резонаторів планарної конструкції.
В роботі розглянуто двомодові резонатори при різних способах їх включення. Спочатку вирішена задача синтезу конструктивних елементів двомодових
резонаторів із розімкненими кінцями та вивчено їх властивості. Потім синтезовано конструктивні елементи двомодових резонаторів із короткозамкненими кінцями, та досліджено їх властивості.
Таким чином, в результаті розвитку теорії двомодових резонаторів, методом параметричного систезу отримано та досліджено чотири варіанти резонаторів, які мають властивості, корисні при побудові смуго-пропускних фільтрів. Ці
резонатори мають покращенні функціональні можливості, а саме: збільшену в
1,4 рази смугу загородження, зменьшені в 1,3 рази розміри резонаторів при тих
же значеннях резонансних частот, що і при використанні однорідних ліній передачі.
Визначено основні показники двомодових планарних резонаторів із розімкненими і з усіма короткозамкненими кінцями на основі ступінчастих ліній.
Виявлена та експериментально підтверджена нова властивість деяких двомодових резонаторів, яка полягає в одночасному існуванні двомодових та одномодових коливань, які чергуються між собою. Експеримент підтвердив розширення
смуги загородження, яке склало 1,4 рази по відношенню до двомодового фільтру
на однорідних лініях. При цьому ширина цієї смуги може змінюватися. Прототип
фільтра з закороченими кінцями запрацював як фільтр з очікуваними характеристиками.Litvintsev S. M. Construction methods and circuit design solutions for microstrip
bandpass filters. — Qualification manuscript.
The dissertation for the scientific degree of candidate of engineering sciences in
the speciality 05.12.13 — «Radio technical devices and means of telecommunications»
(17 — Electronics and telecommunications). — National Technical University of
Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” Ministry of Education and Science
of Ukraine, Kyiv, 2023.
An actual scientific and engineering problem of developing construction methods
and new circuit solutions for bandpass filters (BPF), which are used in modern
wireless communication systems, are solved in this dissertation.
The functional capabilities of the coupling matrix were expanded by modifying
it in the first chapter. Examples of the inapplicability of the coupling matrix were considered.
The analysis of the through-type resonator, which is the cause of the specified
inapplicability, was carried out. The problem of coupling matrix modification was
solved, which leads to correct frequency characteristics and expanding the application
of coupling matrix.
A detailed examination of the through-type resonator, included as the two-port
network, showed that the coupling configuration depends on its structure. This is used
to modify the coupling matrix accordingly so that it correctly determines the frequency
characteristics. The modification consists in changing the signs of some elements of
the coupling matrix according to the rules established in this work. The rules for the
modification of the couping matrix established in this work are given using some examples.
To check the modification in coupling matrix, appropriate filters were made. The
measured characteristics of these filters confirmed the proposed changes.
In the second chapter, BPFs with mixed coupling between adjacent resonators
are considered. An analysis of the location of the transmission zeros of such filters and
the relationship between the linear and conventional presentation forms of the mixed
couping was carried out. The synthesis method of such filters based on the use of a
conductivity inverter for mixed coupling is proposed.
Unlike usual coupling, mixed coupling is characterized by three, not two, characteristic
frequencies: an even mode and an odd mode of coupled oscillations, and frequency
of transmission zero. These frequencies can be determined when the resonators
are weakly connected.
Since the mixed coupling coefficient in its usual form cannot be used in the coupling
matrix, it is necessary to have another representation form to calculate the frequency
characteristics of BPF. The linear form of the coupling coefficient at the normalized
frequency was used. In this case, it becomes possible to use the coupling matrix
to calculate the parameters of the band-pass filter in the case when it uses mixed
couplings.
An effective method of synthesizing filters with mixed couplings between adjacent
resonators is proposed in this work. The method is based on the well-known technique
of using conductivity inverters, the circuits of which now contain parallel circuits
according to the mixed couplings of resonators. The EM modeling results confirmed
this filter synthesis procedure.
The relationship between linear and conventional representation forms of mixed
coupling is established. For the first time, a method for the analytical synthesis of BPF
with mixed couplings between adjacent resonators. It is based on the use of conductivity
inverters for mixed couplings. At the same time, the filter selectivity was achieved,
which corresponds to more complex structures without complicating the filter design.
In the third chapter, filters with lumped-distributed couplings, wide stopband
and increased one-sided selectivity are considered. Two methods of increasing the
stopband in combline and pseudocombline filters are proposed.
Since the basis of combline BPFs are interconnected quarter-wave resonators,
the proposed method is based on the regularity of the change of anti-resonance frequencies
associated with the change of the connection coordinate to quarter-wave resonator.
Based on the input conductivity expression of the quarter-wave resonator, the
coordinates of the special connection points to this resonator are determined. The use
of these points leads to the suppression of parasitic transmission bands in the combline
bandpass filter. In addition, it was found that the use of one special connection point
leads to the suppression of not one, but several periodically located resonance frequencies
of the quarter-wave resonator. Thus, if several special coordinates of the connection
points are used in one filter, then in this case it is possible to achieve a significant
stopband expansion in a combline band-pass filter.
A similar method of stopband expanding was developed for a pseudocombline
band-pass filter, which is based on half-wave resonators. In the case of a pseudocombline,
the use of one connection point with a special coordinate also leads to the suppression
of not only one parasitic resonant frequency of the half-wave resonator, but to
the simultaneous suppression of several periodically located resonant frequencies of
the half-wave resonator. The distribution law of these frequensies is also determined
and proposed by the author.
Today a large number of small-sized passive components (capacitors, inductances)
with a high Q-factor for use in ultra-high-frequency devices have appeared on
the market. So, the simultaneous using of microstrip resonators and small-sized lumped
elements leads to the appearance of a new type of connections in pass-band filters,
which can be called lumped-distributed coupling. Therefore, methods, which help to
calculate the values of all elements included in a band-pass filter, which is built on the
basis of such lumped-distributed connections, are needed. The author proposed a technique
that allows us to determine the value of all elements, which are used to construct
a band-pass filter with lumped-distributed couplings.
Thus, this work solves the problem of stopband expanding in combline and pseudocombline
filters by using lumped-distributed mixed couplings between adjacent resonators,
and a new calculation method based on the displacement trajectories of the
anti-resonant frequencies of the used resonators.
Verification of the method of stopband expanding based on the frequency shifts
trajectories was carried out on the measuring results the parameters of the filter created
according to the proposed method. We obtained the stopband expansion by more than
three times. The design process is presented as algorithm that unifies this process for
engineer.
The fourth chapter considers the possibility of expanding the functional capabilities
of multimode resonators and filters. An analysis of dual-mode planar resonators
with open and short-circuited ends based on stepped lines was carried out. The dualmode
band-pass filters were experimentally investigated.
Existing dual-mode T-junction resonators are functionally limited because they
use uniform transmission line segments. In this work, it is proposed to replace these
segments with step-impedance resonators, and to determine the potential capabilities
of these new formed dual-mode planar resonators.
The paper considers dual-mode resonators with different ways of their connection.
Firstly, the synthesis problem of structural elements of dual-mode resonators with
open ends was solved and their properties were studied. Then, the structural elements
of dual-mode resonators with short-circuited ends were synthesized, and their properties
were investigated.
As a result of the development of the theory of dual-mode resonators, by the
method of parametric synthesis we propose and investigate four variants of resonators,
which have properties useful in the design of band-pass filters. These resonators have
improved functionality, namely: a stopband increased by 1.4 times, the dimensions of
the resonators reduced by 1.3 times at the same values of resonant frequencies as when
using uniform transmission lines.
The main parameters of dual-mode planar resonators with open and all shortcircuited
ends based on step-impedance resonators are determined. A new property of
some dual-mode resonators, which consists in the simultaneous existence of alternating
dual-mode and one-mode oscillations, was discovered and experimentally confirmed.
The experiment confirmed the stopband expansion, which was 1.4 times compared to
the dual-mode filter based on uniform lines. At the same time, the width of this band
may vary. The prototype filter with shorted ends performed as a filter with the expected
characteristics