Particle image velocimetry measurements of the interaction of synthetic jets with a zero-pressure gradient laminar boundary layer

Copyright @ 2010 American Institute of PhysicsAn experimental investigation of the interaction between a synthetic jet actuator and a zero-pressure gradient laminar boundary layer is reported. The aim of this study is to quantify the impact of synthetic jet vortical structures; namely, hairpin vortices, stretched vortex rings and tilted vortex rings on a boundary layer, and to assess their relative potential for flow separation control. Streamwise particle image velocimetry was employed in a water flume (free stream boundary layer thickness Reynolds number of 500 and boundary layer thickness-to-jet orifice diameter ratio of 4) to obtain phase- and time-averaged boundary layer profile information of the impact of synthetic jets near the wall. The potential for flow control was assessed by analyzing near wall fluid mixing, realized by the measure of increase in wall shear stress produced by a passing vortex. Hairpin vortices (produced at a jet-to-free stream velocity ratio, VR=0.32 and dimensionless stroke length, L=1.6) and stretched vortex rings (VR=0.27; L=2.7) exhibit characteristics akin to a streamwise vortex pair with a common upwash. Conversely, tilted vortex rings (VR=0.54; L=2.7) induce a streamwise vortex pair in the near wall region with a common downwash. Wall shear stress measurements show that synthetic jets composed of stretched vortex rings offer the best combination of near wall fluid mixing, persistency, and low rms fluctuations for potential applications of flow separation control.Financial support from the Engineering and Physical Sciences Research Council (EPSRC Grant No. AF566NEZ) was used for this work

Investigation of passive flow control techniques to enhance the stall characteristics of a microlight aircraft

This report investigates the enhancement of aerodynamic stall characteristics of a Skyranger microlight aircraft by the use of passive flow control techniques, namely vortex generators and turbulators. Each flow control device is designed and scaled to application conditions. Force balance measurements and surface oil flow visualisation are carried out on a half-model of the microlight to further investigate the nature of the flow on the aircraft with and without the flow control devices. The results indicate a clear advantage to the use of turbulators compared with vortex generators. Turbulators increased the maximum lift coefficient by 2.8%, delayed the onset of stall by increasing the critical angle by 17.6% and reduced the drag penalty at both lower (pre-stall) and higher angles of attack by 8% compared to vortex generators. With vortex generators applied, the results indicated a delayed stall with an increase in the critical angle by 2% and a reduced drag penalty at higher angles of attack

Vortex methods for separated flows

The numerical solution of the Euler or Navier-Stokes equations by Lagrangian vortex methods is discussed. The mathematical background is presented in an elementary fashion and includes the relationship with traditional point-vortex studies, the convergence to smooth solutions of the Euler equations, and the essential differences between two- and three-dimensional cases. The difficulties in extending the method to viscous or compressible flows are explained. The overlap with the excellent review articles available is kept to a minimum and more emphasis is placed on the area of expertise, namely two-dimensional flows around bluff bodies. When solid walls are present, complete mathematical models are not available and a more heuristic attitude must be adopted. The imposition of inviscid and viscous boundary conditions without conformal mappings or image vortices and the creation of vorticity along solid walls are examined in detail. Methods for boundary-layer treatment and the question of the Kutta condition are discussed. Practical aspects and tips helpful in creating a method that really works are explained. The topics include the robustness of the method and the assessment of accuracy, vortex-core profiles, timemarching schemes, numerical dissipation, and efficient programming. Calculations of flows past streamlined or bluff bodies are used as examples when appropriate

Review of delta wing space shuttle vehicle dynamics

The unsteady aerodynamics of the proposed delta planform, high cross range, shuttle orbiters, are investigated. It is found that these vehicles are subject to five unsteady-flow phenomena that could compromise the flight dynamics. The phenomena are as follows: (1) leeside shock-induced separation, (2) sudden leading-edge stall, (3) vortex burst, (4)bow shock-flap shock interaction, and (5) forebody vorticity. Trajectory shaping is seen as the most powerful means of avoiding deterimental effects of the stall phenomena; however, stall must be fixed or controlled when traversing the stall region. Other phenomana may be controlled by carefully programmed control deflections and some configuration modifications. Ways to alter the occurrence of the various flow conditions are explored

Lagrangian and spectral analysis of the forced flow past a circular cylinder using pulsed tangential jets

We numerically investigate the influence of pulsed tangential jets on the flow past a circular cylinder. To this end a spectral-Lagrangian dual approach is completed on the basis of time-series data. The analysis reveals that the flow response to unsteady for- cing is driven by strong interactions between shear layers and pulsed jets. The latter preferentially lead to either the lock-on regime or the quasi-steady vortex feeding regime whether the excitation frequency is of the order of, or significantly greater than the fre- quency of the natural instability. The intensity of the wake vortices is mainly influenced by the momentum coefficient through the introduction of opposite-sign vorticity in the shear layers. This feature is emphasized using a modal-based time reconstruction, i.e. by reconstructing the flow field upon a specific harmonic spectrum associated with a charac- teristic time-scale. The quasi-steady regime exhibits small-scale counter-rotating vortices that circumscribe the separated region. In the lock-on regime, atypical wake patterns as 2P or P+S can be observed, depending on the forcing frequency and the momentum coefficient, highlighting remarkable analogies with oscillating cylinders

Turbulent boundary layer separation over a rearward facing ramp and its control through mechanical excitation

A vane oscillating about a fixed point at the inlet to a two-dimensional 20 degree rearward facing ramp has proven effective in delaying the separation of a turbulent boundary layer. Measurements of the ramp surface static pressure coefficient obtained under the condition of vane oscillation and constant inlet velocity revealed that two different effects occurred with surface distance along the ramp. In the vicinity of the oscillating vane, the pressure coefficients varied as a negative function of the vane's trailing edge rms velocity; the independent variable on which the rms velocity depends are the vane's oscillation frequency and its displacement amplitude. From a point downstream of the vane to the exit of the ramp; however, the pressure coefficient varied as a more complex function of the two independent variables. That is, it was found to vary as a function of the vane's oscillation frequency throughout the entire range of frequencies covered during the test, but over only a limited range of the trailing edge displacement amplitudes covered. More specifically, the value of the pressure coefficient was independent of increases in the vane's displacement amplitude above approximately 35 inner wall units of the boundary layer. Below this specific amplitude it varied as a function of the vane's trailing edge rms velocity. This height is close to the upper limit of the buffer layer. A parametric study was made to determine the variation of the maximum static pressure recovery as a function of the vane's oscillation frequency, for several ramp inlet velocities and a constant displacement amplitude of the vane's trailing edge. The results indicate that the phenomenon producing the optimum delay of separation may be Strouhal number dependent. Corona anemometer measurements obtained in the inner wall regions of the boundary layer for the excited case reveal a large range of unsteadiness in the local velocities. These measurements imply the existence of inflections in the profiles, which provide a mechanism for resulting inviscid flow instabilities to produce turbulence in the near wall region, thereby delaying separation of the boundary layer

Vortex shedding in a two-dimensional diffuser: theory and simulation of separation control by periodic mass injection

We develop a reduced-order model for large-scale unsteadiness (vortex shedding) in a two-dimensional diffuser and use the model to show how periodic mass injection near the separation point reduces stagnation pressure loss. The model estimates the characteristic frequency of vortex shedding and stagnation pressure loss by accounting for the accumulated circulation due to the vorticity flux into the separated region. The stagnation pressure loss consists of two parts: a steady part associated with the time-averaged static pressure distribution on the wall, and an unsteady part caused by vortex shedding. To validate the model, we perform numerical simulations of compressible unsteady laminar diffuser flows in two dimensions. The model and simulation show good agreement as we vary the Mach number and the area ratio of the diffuser. To investigate the effects of periodic mass injection near the separation point, we also perform simulations over a range of the injection frequencies. Periodic mass injection causes vortices to be pinched off with a smaller size as observed in experiments. Consequently, their convective velocity is increased, absorption of circulation from the wall is enhanced, and the reattached point is shifted upstream. Thus, in accordance with the model, the stagnation pressure loss, particularly the unsteady part, is substantially reduced even though the separation point is nearly unchanged. This study helps explain experimental results of separation control using unsteady mass injection in diffusers and on airfoils

Aerodynamics of vortex generators

An experimental and theoretical study was undertaken of the separation delay and dramatic boundary-layer thinning that can occur in vortex-generator installations. Wind tunnel measurements of the dynamic-pressure profile downstream of a vortex generator were found to compare under certain conditions with that downstream of a suction slit, while water-tunnel visualization studies of vortex-generator height and geometry suggested optimum configurations, and only a minor effect of base porosity. A series of progressively more complex inviscid flow models was developed to be applied to a 3-D integral boundary-layer code. This code predicted layer thinning downstream of the suction site of the vortex models, and other observed features. Thin-layer Navier-Stokes equations are now being used with the ultimate goal of clarifying the physical processes involved in vortex generator performance and developing calculational procedures capable of predicting it