Test Planning for 3D SICs using ILP

In this paper we propose a test planning scheme for corebased 3D stacked integrated circuits where the total test cost for wafer sort of each individual chip and the test cost of the complete stack at package test is minimized. We use an Integer Linear Programming (ILP) model to find the optimal test cost, which is given as the weighted sum of the test time and the test access mechanism (TAM). As ILP is time consuming, we use a scheme to bound the test time and the TAM such that the search space is reduced. The proposed bounding scheme and the ILP model were applied on several ITC’02 benchmarks and the results show that optimal solutions were obtained at low computation time

Thermal-Aware Test Schedule and TAM Co-Optimization for Three-Dimensional IC

[[abstract]]Testing is regarded as one of the most difficult challenges for three-dimensional integrated circuits (3D ICs). In this paper, we want to optimize the cost of TAM (test access mechanism) and the test time for 3D IC. We used both greedy and simulated annealing algorithms to solve this optimization problem. We compare the results of two assumptions: soft-die mode and hard-die mode. The former assumes that the DfT of dies cannot be changed, while the latter assumes that the DfT of dies can be adjusted. The results show that thermal-aware cooptimization is essential to decide the optimal TAM and test schedule. Blindly adding TAM cannot reduce the total test cost due to temperature constraints. Another conclusion is that soft-die mode is more effective than hard-die mode to reduce the total test cost for 3D IC.[[notice]]補正完畢[[booktype]]電子

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount

A survey on scheduling and mapping techniques in 3D Network-on-chip

Network-on-Chips (NoCs) have been widely employed in the design of multiprocessor system-on-chips (MPSoCs) as a scalable communication solution. NoCs enable communications between on-chip Intellectual Property (IP) cores and allow those cores to achieve higher performance by outsourcing their communication tasks. Mapping and Scheduling methodologies are key elements in assigning application tasks, allocating the tasks to the IPs, and organising communication among them to achieve some specified objectives. The goal of this paper is to present a detailed state-of-the-art of research in the field of mapping and scheduling of applications on 3D NoC, classifying the works based on several dimensions and giving some potential research directions

Integrating simultaneous bi-direction signalling in the test fabric of 3D stacked integrated circuits.

Jennions, Ian K. - Associate SupervisorThe world has seen significant advancements in electronic devices’ capabilities, most notably the ability to embed ultra-large-scale functionalities in lightweight, area and power-efficient devices. There has been an enormous push towards quality and reliability in consumer electronics that have become an indispensable part of human life. Consequently, the tests conducted on these devices at the final stages before these are shipped out to the customers have a very high significance in the research community. However, researchers have always struggled to find a balance between the test time (hence the test cost) and the test overheads; unfortunately, these two are inversely proportional. On the other hand, the ever-increasing demand for more powerful and compact devices is now facing a new challenge. Historically, with the advancements in manufacturing technology, electronic devices witnessed miniaturizing at an exponential pace, as predicted by Moore’s law. However, further geometric or effective 2D scaling seems complicated due to performance and power concerns with smaller technology nodes. One promising way forward is by forming 3D Stacked Integrated Circuits (SICs), in which the individual dies are stacked vertically and interconnected using Through Silicon Vias (TSVs) before being packaged as a single chip. This allows more functionality to be embedded with a reduced footprint and addresses another critical problem being observed in 2D designs: increasingly long interconnects and latency issues. However, as more and more functionality is embedded into a small area, it becomes increasingly challenging to access the internal states (to observe or control) after the device is fabricated, which is essential for testing. This access is restricted by the limited number of Chip Terminals (IC pins and the vertical Through Silicon Vias) that a chip could be fitted with, the power consumption concerns, and the chip area overheads that could be allocated for testing. This research investigates Simultaneous Bi-Directional Signaling (SBS) for use in Test Access Mechanism (TAM) designs in 3D SICs. SBS enables chip terminals to simultaneously send and receive test vectors on a single Chip Terminal (CT), effectively doubling the per-pin efficiency, which could be translated into additional test channels for test time reduction or Chip Terminal reduction for resource efficiency. The research shows that SBS-based test access methods have significant potential in reducing test times and/or test resources compared to traditional approaches, thereby opening up new avenues towards cost-effectiveness and reliability of future electronics.PhD in Manufacturin

Design-for-Test and Test Optimization Techniques for TSV-based 3D Stacked ICs

<p>As integrated circuits (ICs) continue to scale to smaller dimensions, long interconnects</p><p>have become the dominant contributor to circuit delay and a significant component of</p><p>power consumption. In order to reduce the length of these interconnects, 3D integration</p><p>and 3D stacked ICs (3D SICs) are active areas of research in both academia and industry.</p><p>3D SICs not only have the potential to reduce average interconnect length and alleviate</p><p>many of the problems caused by long global interconnects, but they can offer greater design</p><p>flexibility over 2D ICs, significant reductions in power consumption and footprint in</p><p>an era of mobile applications, increased on-chip data bandwidth through delay reduction,</p><p>and improved heterogeneous integration.</p><p>Compared to 2D ICs, the manufacture and test of 3D ICs is significantly more complex.</p><p>Through-silicon vias (TSVs), which constitute the dense vertical interconnects in a</p><p>die stack, are a source of additional and unique defects not seen before in ICs. At the same</p><p>time, testing these TSVs, especially before die stacking, is recognized as a major challenge.</p><p>The testing of a 3D stack is constrained by limited test access, test pin availability,</p><p>power, and thermal constraints. Therefore, efficient and optimized test architectures are</p><p>needed to ensure that pre-bond, partial, and complete stack testing are not prohibitively</p><p>expensive.</p><p>Methods of testing TSVs prior to bonding continue to be a difficult problem due to test</p><p>access and testability issues. Although some built-in self-test (BIST) techniques have been</p><p>proposed, these techniques have numerous drawbacks that render them impractical. In this dissertation, a low-cost test architecture is introduced to enable pre-bond TSV test through</p><p>TSV probing. This has the benefit of not needing large analog test components on the die,</p><p>which is a significant drawback of many BIST architectures. Coupled with an optimization</p><p>method described in this dissertation to create parallel test groups for TSVs, test time for</p><p>pre-bond TSV tests can be significantly reduced. The pre-bond probing methodology is</p><p>expanded upon to allow for pre-bond scan test as well, to enable both pre-bond TSV and</p><p>structural test to bring pre-bond known-good-die (KGD) test under a single test paradigm.</p><p>The addition of boundary registers on functional TSV paths required for pre-bond</p><p>probing results in an increase in delay on inter-die functional paths. This cost of test</p><p>architecture insertion can be a significant drawback, especially considering that one benefit</p><p>of 3D integration is that critical paths can be partitioned between dies to reduce their delay.</p><p>This dissertation derives a retiming flow that is used to recover the additional delay added</p><p>to TSV paths by test cell insertion.</p><p>Reducing the cost of test for 3D-SICs is crucial considering that more tests are necessary</p><p>during 3D-SIC manufacturing. To reduce test cost, the test architecture and test</p><p>scheduling for the stack must be optimized to reduce test time across all necessary test</p><p>insertions. This dissertation examines three paradigms for 3D integration - hard dies, firm</p><p>dies, and soft dies, that give varying degrees of control over 2D test architectures on each</p><p>die while optimizing the 3D test architecture. Integer linear programming models are developed</p><p>to provide an optimal 3D test architecture and test schedule for the dies in the 3D</p><p>stack considering any or all post-bond test insertions. Results show that the ILP models</p><p>outperform other optimization methods across a range of 3D benchmark circuits.</p><p>In summary, this dissertation targets testing and design-for-test (DFT) of 3D SICs.</p><p>The proposed techniques enable pre-bond TSV and structural test while maintaining a</p><p>relatively low test cost. Future work will continue to enable testing of 3D SICs to move</p><p>industry closer to realizing the true potential of 3D integration.</p>Dissertatio

Test Planning and Test Access Mechanism Design for 3D SICs

In this paper we propose a scheme for test planning and test access mechanism (TAM) design for stacked integrated circuits (SICs) that are designed in a core-based manner. Our scheme minimizes the test cost, which is given as the weighted sum of the test time and the TAM width. The test cost is evaluated for a test flow that consists of a wafer sort test of each individual chip and a package test of the complete stack of chips. We use an Integer Linear Programming (ILP) model to find the optimal test cost. The ILP model is implemented on several designs constructed from ITC’02 benchmarks. The experimental results show significant reduction in test cost compared to when using schemes, which are optimized for non-stacked chips

Design and Implementation of High QoS 3D-NoC using Modified Double Particle Swarm Optimization on FPGA

One technique to overcome the exponential growth bottleneck is to increase the number of cores on a processor, although having too many cores might cause issues including chip overheating and communication blockage. The problem of the communication bottleneck on the chip is presently effectively resolved by networks-on-chip (NoC). A 3D stack of chips is now possible,&nbsp;thanks to recent developments in IC manufacturing techniques, enabling to reduce of chip area while increasing chip throughput and reducing power consumption. The automated process associated with mapping applications to form&nbsp;three-dimensional NoC architectures is a significant new path in 3D NoC research. This work proposes a 3D NoC partitioning approach that can identify the 3D NoC region that has to be mapped. A double particle swarm optimization (DPSO) inspired algorithmic technique, which may combine the characteristics having neighbourhood search and genetic architectures, also addresses the challenge of a particle swarm algorithm descending into local optimal solutions. Experimental evidence supports the claim that this hybrid optimization algorithm based on Double Particle Swarm Optimisation outperforms the conventional heuristic technique in terms of output rate and loss in energy. The findings demonstrate that in a network of the same size, the newly introduced router delivers the lowest loss on the longest path. &nbsp;Three factors, namely energy, latency or&nbsp;delay, and throughput, are compared between the suggested 3D mesh ONoC and its 2D version. When comparing power consumption between 3D ONoC and its electronic and 2D equivalents, which both have 512 IP cores, it may save roughly 79.9% of the energy used by the electronic counterpart and 24.3% of the energy used by the latter. The network efficiency of the 3D mesh ONoC is simulated by DPSO in a variety of configurations. The outcomes also demonstrate an increase in performance over the 2D ONoC. As a flexible communication solution, Network-On-Chips (NoCs) have been frequently employed in the development of multiprocessor system-on-chips (MPSoCs). By outsourcing their communication activities, NoCs permit on-chip Intellectual Property (IP) cores to communicate with one another and function at a better level. The important components in assigning application duties, distributing the work to the IPs, and coordinating communication among them are mapping and scheduling methods. This study aims to present an&nbsp;entirely advanced form of research in the area of 3D NoC&nbsp;mapping and scheduling applications, grouping the results according to various parameters and offering several suggestions for further research

TSV placement optimization for liquid cooled 3D-ICs with emerging NVMs

Three dimensional integrated circuits (3D-ICs) are a promising solution to the performance bottleneck in planar integrated circuits. One of the salient features of 3D-ICs is their ability to integrate heterogeneous technologies such as emerging non-volatile memories (NVMs) in a single chip. However, thermal management in 3D-ICs is a significant challenge, owing to the high heat flux (~ 250 W/cm2). Several research groups have focused either on run-time or design-time mechanisms to reduce the heat flux and did not consider 3D-ICs with heterogeneous stacks. The goal of this work is to achieve a balanced thermal gradient in 3D-ICs, while reducing the peak temperatures. In this research, placement algorithms for design-time optimization and choice of appropriate cooling mechanisms for run-time modulation of temperature are proposed. Specifically, an architectural framework which introduce weight-based simulated annealing (WSA) algorithm for thermal-aware placement of through silicon vias (TSVs) with inter-tier liquid cooling is proposed for design-time. In addition, integrating a dedicated stack of emerging NVMs such as RRAM, PCRAM and STTRAM, a run-time simulation framework is developed to analyze the thermal and performance impact of these NVMs in 3D-MPSoCs with inter-tier liquid cooling. Experimental results of WSA algorithm implemented on MCNC91 and GSRC benchmarks demonstrate up to 11 K reduction in the average temperature across the 3D-IC chip. In addition, power density arrangement in WSA improved the uniformity by 5%. Furthermore, simulation results of PARSEC benchmarks with NVM L2 cache demonstrates a temperature reduction of 12.5 K (RRAM) compared to SRAM in 3D-ICs. Especially, RRAM has proved to be thermally efficient replacement for SRAM with 34% lower energy delay product (EDP) and 9.7 K average temperature reduction