Source parameters of the 2017 M_w 6.2 Yukon earthquake doublet inferred from coseismic GPS and ALOS-2 deformation measurements

We investigated an M_w ∼ 6.2 earthquake doublet on the border of the USA and Canada using ALOS2 Light-of-Sight displacements and GPS measurements. We selected three L-band ALOS-2 interfergorams with temporal baselines of one yr to extract coseismic deformation maps, in which master and slave images were both acquired in July. A subpixel-based alignment and another range spectral splitting techniques under the GAMMA InSAR software framework were applied to improve the interferometric coherence and reduce the effects of phase anomalies in two of the three interferometric pairs due to either ionospheric delay or a potential focusing issues in the generation of the ALOS2 SLC data. The updated interferograms convincingly reveal deformation fringe patterns produced by the two earthquakes. We conducted a nonlinear geophysical inversion to estimate the geometric parameters of the earthquakes with the InSAR and GPS measurements. The best-fitting model shows that a thrust faulting on a reverse fault and left-lateral strike-slip faulting on a nearly vertical fault with the centroid depths of 9.3±0.6 and 8.4±0.7 km, respectively, are most likely responsible for the earthquake doublet. The eastern Denali fault (EDF) and Duke River fault are major active faults in the region and the earthquake doublet could be due to reactivation of the part of the two faults system

Techniques and Tools for Estimating Ionospheric Effects in Interferometric and Polarimetric SAR Data

The InSAR Scientific Computing Environment (ISCE) is a flexible, extensible software tool designed for the end-to-end processing and analysis of synthetic aperture radar data. ISCE inherits the core of the ROI_PAC interferometric tool, but contains improvements at all levels of the radar processing chain, including a modular and extensible architecture, new focusing approach, better geocoding of the data, handling of multi-polarization data, radiometric calibration, and estimation and correction of ionospheric effects. In this paper we describe the characteristics of ISCE with emphasis on the ionospheric modules. To detect ionospheric anomalies, ISCE implements the Faraday rotation method using quadpolarimetric images, and the split-spectrum technique using interferometric single-, dual- and quad-polarimetric images. The ability to generate co-registered time series of quad-polarimetric images makes ISCE also an ideal tool to be used for polarimetric-interferometric radar applications

Modelling co- and post-seismic displacements revealed by InSAR, and their implications for fault behaviour

The ultimate goal of seismology is to estimate the timing, magnitude and potential spatial extent of future seismic events along pre-existing faults. Based on the rate-state friction law, several theoretical physical earthquake models have been proposed towards this goal. Tectonic loading rate and frictional properties of faults are required in these models. Modern geodetic observations, e.g. GPS and InSAR, have provided unprecedented near-field observations following large earthquakes. In theory, according to the frictional rate and state asperity earthquake model, velocity-weakening regions holding seismic motions on faults should be separated with velocity-strengthening regions within which faults slip only aseismically. However, early afterslip following the 2011 MW 9.1 Tohoku-Oki earthquake revealed from GPS measurements was largely overlaid on the historical rupture zones, which challenged the velocity weakening asperity model. Therefore, the performance of the laboratory based friction law in the natural events needs further investigation, and the factors that may affect the estimates of slip models through geodetic modelling should also be discussed systematically. In this thesis, several moderate-strong events were investigated in order to address this important issue. The best-fit co- and post-seismic slip models following the 2009 MW 6.3 Haixi, Qinghai thrust-slip earthquake determined by InSAR deformation time-series suggest that the maximum afterslip is concentrated in the same area as the coseismic slip model, which is similar to the patterns observed in the 2011 Japan earthquake. In this case, complex geometric asperity may play a vital role in the coseismic nucleation and postseismic faulting. The major early afterslip after the 2011 MW 7.1 Van mainshock, which was revealed by one COSMO-SkyMed postseismic interferogram, is found just above the coseismic slip pattern. In this event, a postseismic modelling that did not allow slip across the coseismic asperity was also tested, suggesting that the slip model without slip in the asperities can explain the postseismic observations as well as the afterslip model without constraints on slip in the asperities. In the 2011 MW 9.1 Tohoku-Oki earthquake, a joint inversion with the GRACE coseismic gravity changes and inland coseismic GPS observations was conducted to re-investigate the coseismic slip model of the mainshock. A comparison of slip models from these different datasets suggests that significant variations of slip models can be observed, particularly the locations of the maximum slips. The joint slip model shows that the maximum slip of ~42 m appears near the seafloor surface close to the Japan Trench. Meanwhile, the accumulative afterslip patterns (slip >2 m) determined in previous studies appear in spatial correlation with the Coulomb stress changes generated using the joint slip model. As a strike-slip faulting event, the 2011 MW 6.8 Yushu earthquake was also investigated through co- and post-seismic modelling with more SAR data than was used in previous study. Best slip models suggest that the major afterslip is concentrated in shallow parts of the faults and between the two major coseismic slip patterns, suggesting that the performance of the rate and state frictional asperity model is appropriate in this event. Other postseismic physical mechanisms, pore-elastic rebound and viscoelastic relaxation have also been examined, which cannot significantly affect the estimate of the shallow afterslip model in this study. It is believed that the shallow afterslip predominantly controlled the postseismic behaviour after the mainshock in this case. In comparison to another 21 earthquakes investigated using geodetic data from other studies, complementary spatial extents between co- and post-seismic slip models can be identified. The 2009 MW 6.3 Qinghai earthquake is an exceptional case, in which the faulting behaviours might be dominated by the fault structure (e.g. fault bending). In conclusion, the major contributions from this thesis include: 1) the friction law gives a first order fit in most of natural events examined in this thesis; 2) geometric asperities may play an important role in faulting during earthquake cycles; 3) significant uncertainties in co- and post-seismic slip models can appreciably bias the estimation of fault frictional properties; 4) new insights derived from each earthquake regarding their fault structures and complex faulting behaviours have been observed in this thesis; and (5) a novel package for geodetic earthquake modelling has been developed, which can handle multiple datasets including InSAR, GPS and land/space based gravity changes