High performance architecture design for large scale fibre-optic sensor arrays using distributed EDFAs and hybrid TDM/DWDM

A distributed amplified dense wavelength division multiplexing (DWDM) array architecture is presented for interferometric fibre optic sensor array systems. This architecture employs a distributed erbium doped fibre amplifier (EDFA) scheme to decrease the array insertion loss, and employs time division multiplexing (TDM) at each wavelength to increase the number of sensors that can be supported. The first experimental demonstration of this system is reported including results which show the potential for multiplexing and interrogating up to 4096 sensors using a single telemetry fibre pair with good system performance. The number can be increased to 8192 by using dual pump sources

Cost-effective aperture arrays for SKA Phase 1: single or dual-band?

An important design decision for the first phase of the Square Kilometre Array is whether the low frequency component (SKA1-low) should be implemented as a single or dual-band aperture array; that is, using one or two antenna element designs to observe the 70-450 MHz frequency band. This memo uses an elementary parametric analysis to make a quantitative, first-order cost comparison of representative implementations of a single and dual-band system, chosen for comparable performance characteristics. A direct comparison of the SKA1-low station costs reveals that those costs are similar, although the uncertainties are high. The cost impact on the broader telescope system varies: the deployment and site preparation costs are higher for the dual-band array, but the digital signal processing costs are higher for the single-band array. This parametric analysis also shows that a first stage of analogue tile beamforming, as opposed to only station-level, all-digital beamforming, has the potential to significantly reduce the cost of the SKA1-low stations. However, tile beamforming can limit flexibility and performance, principally in terms of reducing accessible field of view. We examine the cost impacts in the context of scientific performance, for which the spacing and intra-station layout of the antenna elements are important derived parameters. We discuss the implications of the many possible intra-station signal transport and processing architectures and consider areas where future work could improve the accuracy of SKA1-low costing.Comment: 64 pages, 23 figures, submitted to the SKA Memo serie

Near infrared spectroscopy for fibre based gas detection

Gas sensing systems based on fibre optic linked near infra red absorption cells are potentially a flexible and effective tool for monitoring accumulations of hazardous and noxious gases in enclosed areas such as tunnels and mines. Additionally the same baseline technology is readily modified to measure concentrations of hydrocarbon fuels - notably but not exclusively methane, and monitoring emissions of greenhouse gases. Furthermore the system can be readily implemented to provide intrinsically safe monitoring over extensive areas at up to ~250 points from a single interrogation unit. In this paper we review our work on fibre coupled gas sensing systems. We outline the basic principles through which repeatable and accurate self calibrating gas measurements may be realised, including the recover of detailed line shapes for non contact temperature and / or pressure measurements in addition to concentration assessments in harsh environments. We also outline our experience in using these systems in extensive networks operating under inhospitable conditions over extended periods extending to several years

Receiver architecture of the thousand-element array (THEA)

As part of the development of a new international radio-telescope SKA (Square Kilometre Array), an outdoor phasedarray prototype, the THousand Element Array (THEA), is being developed at NFRA. THEA is a phased array with 1024 active elements distributed on a regular grid over a surface of approximately 16 m2. The array is organised into 16 units denoted as tiles. THEA operates in the frequency band from 750 to 1500 MHz.\ud On a tile the signals from 64 antenna elements are converted into two independent RF beams. Two times 16 beams can be made simultaneously with full sensitivity by the real-time digital beam former of the THEA system. At the output of each tile the analog RF signal from a beam is converted into a 2 × 12-bit digital quadrature representation by a receiver system.\ud A double super-heterodyne architecture is used to mix the signal band of interest to an intermediate frequency of 210 MHz. The IF-signal is shifted to baseband by means of a partly digitally implemented I/Q mixer scheme. After a quadrature mixer stage, the I and Q signals are digitised by means of 12 bit A/D converters at 40 MS/s. Implementing a part of the mixing scheme digitally offers the flexibility to use different I/Q architectures, e.g. Hartley and Weaver mixer setups. This way the effect of RFI in different mixing architectures can be analyzed. After the digital processing, the samples are multiplexed, serialised and transported over fibres to the central adaptive digital beam former unit where the signals from all tiles are combined giving 32 beams.\ud This paper focuses on the design choices and the final implementation of the THEA system. In particular, the receiver architecture is addressed. A digital solution is presented, which enables switching between a Hartley and a Weaver based mixer scheme

Access and metro network convergence for flexible end-to-end network design

This paper reports on the architectural, protocol, physical layer, and integrated testbed demonstrations carried out by the DISCUS FP7 consortium in the area of access - metro network convergence. Our architecture modeling results show the vast potential for cost and power savings that node consolidation can bring. The architecture, however, also recognizes the limits of long-reach transmission for low-latency 5G services and proposes ways to address such shortcomings in future projects. The testbed results, which have been conducted end-to-end, across access - metro and core, and have targeted all the layers of the network from the application down to the physical layer, show the practical feasibility of the concepts proposed in the project

Hamiltonians for one-way quantum repeaters

Quantum information degrades over distance due to the unavoidable imperfections of the transmission channels, with loss as the leading factor. This simple fact hinders quantum communication, as it relies on propagating quantum systems. A solution to this issue is to introduce quantum repeaters at regular intervals along a lossy channel, to revive the quantum signal. In this work we study unitary one-way quantum repeaters, which do not need to perform measurements and do not require quantum memories, and are therefore considerably simpler than other schemes. We introduce and analyze two methods to construct Hamiltonians that generate a repeater interaction that can beat the fundamental repeaterless key rate bound even in the presence of an additional coupling loss, with signals that contain only a handful of photons. The natural evolution of this work will be to approximate a repeater interaction by combining simple optical elements.Comment: 8 pages, 3 figure

iBROW – innovative ultra-BROadband ubiquitous wireless communications through terahertz transceivers

No abstract available

Demonstration of wireless backhauling over long-reach PONs

An IEEE 802.16e-2005 (WiMAX) compliant, longreach passive optical network is demonstrated, focusing on the development of next generation optical access with transparent wireless backhauling. In addition to the extended feeder reach, a wavelength band overlay is used to enhance network scalability by maintaining passive splitting in the field and with some design modification at the optical line terminal and remote base station. Radio-over-fiber is used to minimize network installation and maintenance costs through the use of simple remote radio heads complemented by frequency division multiplexing to address individual base stations. The implementation of overlapping radio cells/sectors is also proposed to provide joint signal processing at wireless user terminals. Experimental measurements confirmed EVMs below -30 and -23 dB downstream and upstream, respectively, over fiber link lengths of up to 84.6 km. In addition, adjacent channel leakage ratio measurements demonstrated that a figure of -45 dB with 40 MHz subcarrier spacing, as specified by the standard, can be readily achieved.Peer reviewe