A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

Circuits and Systems Advances in Near Threshold Computing

Modern society is witnessing a sea change in ubiquitous computing, in which people have embraced computing systems as an indispensable part of day-to-day existence. Computation, storage, and communication abilities of smartphones, for example, have undergone monumental changes over the past decade. However, global emphasis on creating and sustaining green environments is leading to a rapid and ongoing proliferation of edge computing systems and applications. As a broad spectrum of healthcare, home, and transport applications shift to the edge of the network, near-threshold computing (NTC) is emerging as one of the promising low-power computing platforms. An NTC device sets its supply voltage close to its threshold voltage, dramatically reducing the energy consumption. Despite showing substantial promise in terms of energy efficiency, NTC is yet to see widescale commercial adoption. This is because circuits and systems operating with NTC suffer from several problems, including increased sensitivity to process variation, reliability problems, performance degradation, and security vulnerabilities, to name a few. To realize its potential, we need designs, techniques, and solutions to overcome these challenges associated with NTC circuits and systems. The readers of this book will be able to familiarize themselves with recent advances in electronics systems, focusing on near-threshold computing

Block level voltage

Over the past years, state-of-art power optimization methods move towards higher abstraction levels that result in more efficient power savings. Among existing power optimization approaches, dynamic power management (DPM) is considered to be one of the most effective strategies. Depending on abstraction levels, DPM can be implemented in different formats but here we focus on scheduling that is more suitable for real-time system design use. This differs from the concurrent scheduling approaches that start from either the HLS (High-Level Synthesis) or RTS (Real-Time System) point of view, we propose a synergy solution of both approaches, namely block-level voltage/frequency scheduling (BLVFS). The presented block-level voltage/ frequency scheduling approach shows a generic solution for low power SoC (System on Chip) system design while the approaches which belong to the HLS and RTS categories have a strong dependency on the system functionalities. Consider a SoC as a combination of heterogeneous functional blocks, our approach provides efficient power savings by dynamically scheduling the scaling of voltage and frequency at the same time. Simulation results indicate that by using heuristic based strategies significant power savings can be achieved

Ultra-low Voltage Digital Circuits and Extreme Temperature Electronics Design

Certain applications require digital electronics to operate under extreme conditions e.g., large swings in ambient temperature, very low supply voltage, high radiation. Such applications include sensor networks, wearable electronics, unmanned aerial vehicles, spacecraft, and energyharvesting systems. This dissertation splits into two projects that study digital electronics supplied by ultra-low voltages and build an electronic system for extreme temperatures. The first project introduces techniques that improve circuit reliability at deep subthreshold voltages as well as determine the minimum required supply voltage. These techniques address digital electronic design at several levels: the physical process, gate design, and system architecture. This dissertation analyzes a silicon-on-insulator process, Schmitt-trigger gate design, and asynchronous logic at supply voltages lower than 100 millivolts. The second project describes construction of a sensor digital controller for the lunar environment. Parts of the digital controller are an asynchronous 8031 microprocessor that is compatible with synchronous logic, memory with error detection and correction, and a robust network interface. The digitial sensor ASIC is fabricated on a silicon-germanium process and built with cells optimized for extreme temperatures