Experimental Evaluation of A Cylinder Actuator Control Using McKibben Muscle

There has been an increased interest in applying pneumatic muscle actuator (PMA) in robotic systems because of its low weight and high compliant characteristics. On the other hand, pneumatic muscle actuator (PMA) is gaining attention in robotic applications because of its low weight and high compliant characteristics. It is known that the McKibben muscle is different from the fluidic cylinder actuator in that the cylinder was unstable in its position and in its velocity in an open-loop system unlike the McKibben that is stable in its position. The modeling and control of McKibben muscle as the actuator for the cylinder are crucial because it is known to have non-linear response, hysteresis and small stroke. In this project, a single acting cylinder model which would have uncontrolled extension to push direction by compressed air, is actuated and controlled using a PMA. The system is designed with two 1.3mm-diameter McKibben muscles attached to the cylinder. Open loop control was used and the result shows that the PMA is able to control the cylinder with good performance

Development of a SMA-fishing-line-McKibben bending actuator

High power-to-weight ratio soft artificial muscles are of overarching importance to enable inherently safer solutions to human-robot interactions. Traditional air driven soft McKibben artificial muscles are linear actuators. It is impossible for them to realize bending motions through a single McKibben muscle. Over two McKibben muscles should normally be used to achieve bending or rotational motions, leading to heavier and larger systems. In addition, air driven McKibben muscles are highly nonlinear in nature, making them difficult to be controlled precisely. A SMA(shape memory alloy)–fishing–line–McKibben (SFLM) bending actuator has been developed. This novel artificial actuator, made of a SMA-fishing-line muscle and a McKibben muscle, was able to produce the maximum output force of 3.0 N and the maximum bending angle (the rotation of the end face) of 61°. This may promote the application of individual McKibben muscles or SMA-fishing-line muscles alone. An output force control method for SFLM is proposed, and based on MATLAB/Simulink software the experiment platform is set up, the effectiveness of control system is verified through output force experiments. A three-fingered SFLM gripper driven by three SFLMs has been designed for a case study, which the maximum carrying capacity is 650.4 ± 0.2 g

Cooperative project by self-bending continuum arms

Designing a multi-robot system provides numerous advantages for many applications such as low cost, multi-tasking and more efficient group work. However, the rigidity of the robots used in industrial and medical applications increases the probability of injury. Therefore, lots of research is done to increase the safety factor for robot-human interaction. As a result, either separation between the human and robot is suggested, or the force shutdown to the robot system is applied. These solutions might be useful for industrial applications, but it is not for medical applications as a direct interaction between the human and the machine is required. To overcome the rigidity problem, a soft robot arm is presented in this paper. Studying the structure and performance of a contraction pneumatic muscle actuator (PMA) is illustrated, then useful strategies are used to implement a multi PMA continuum arm to increase the performance options for such types of the actuator. Moreover, twin arms are constructed to organise a collaborative project depending on the performance abilities of the proposed arms and end effectors

The design, kinematics and torque analysis of the self-bending soft contraction actuator

This article presents the development of a self-bending contraction actuator (SBCA) through analysis of its structure, kinematics, and torque formulas, and then explores its applications. The proposed actuator has been fabricated by two methods to prove the efficiency of the human body inspiration, which represents the covering of human bones by soft tissues to protect the bone and give the soft texture. The SBCA provides bending behaviour along with a high force to-weight ratio. As with the simple pneumatic muscle actuator (PMA), the SBCA is soft and easy to implement. Both the kinematics and the torque formula presented for the SBCA are scalable and can be used with different actuator sizes. The bending actuator has been tested under an air pressure up to 500 kPa, and the behaviour of its bending angle, parameters, dimensions, and the bending torques have been illustrated. On the other hand, the experiments showed the efficient performances of the actuator and validate the proposed kinematics. Therefore, the actuator can be used in many different applications, such as soft grippers and continuum arms

Pneumatic Hyperelastic Robotic End-Effector for Grasping Soft Curved Organic Objects

Pneumatically-driven soft robotic grippers can elastically deform to grasp delicate, curved organic objects with minimal surface damage. However, common actuators have complex geometries and are fabricated with ultra-soft hyperelastic elastomers not originally intended for scientific applications. The complexity of the actuator geometry and extreme nonlinearity of their material’s stress-strain behaviour make it difficult to predict the actuator’s deformation prior to experimentation. In this work, a compact soft pneumatic gripper made with polydimethylsiloxane (PDMS) is developed for grasping delicate organic objects, analyzed through computational modelling and experimentally validated. COMSOL Multiphysics is used to simulate the impact of geometrical parameters on the actuator’s behaviour, allowing for the refinement of the proposed geometry prior to fabrication. Optimal parameters are selected for fabrication, with experimental tests matching simulations within ± 1 mm. Gripper performance is evaluated for three actuator wall thicknesses in terms of contact area with target, contact force, and maximum payload before slippage. The comparative assessment between simulations and experiments demonstrate that the proposed soft actuators can be used in robotic grippers tailored for grasping delicate objects without damaging their surface. Furthermore, analysis of the actuators provides additional insight on how to design simple but effective soft systems

Active soft end effectors for efficient grasping and safe handling

The end effector is a major part of a robot system and it defines the task the robot can perform. However, typically, a gripper is suited to grasping only a single or relatively small number of different objects. Dexterous grippers offer greater grasping ability but they are often very expensive, difficult to control and are insufficiently robust for industrial operation. This paper explores the principles of soft robotics and the design of low-cost grippers able to grasp a broad range of objects without the need for complex control schemes. Two different soft end effectors have been designed and built and their physical structure, characteristics and operational performances have been analysed. The soft grippers deform and conform to the object being grasped, meaning they are simple to control and minimal grasp planning is required. The soft nature of the grippers also makes them better suited to handling fragile and delicate objects than a traditional rigid gripper

DEVELOPMENT OF A SOFT PNEUMATIC ACTUATOR FOR MODULAR ROBOTIC MECHANISMS

Soft robotics is a widely and rapidly growing field of research today. Soft pneumatic actuators, as a fundamental element in soft robotics, have gained huge popularity and are being employed for the development of soft robots. During the last decade, a variety of hyper-elastic robotic systems have been realized. As the name suggests, such robots are made up of soft materials, and do not have any underlying rigid mechanical structure. These robots are actuated employing various methods like pneumatic, electroactive, jamming etc. Generally, in order to achieve a desired mechanical response to produce required actuation or manipulation, two or more materials having different stiffness are utilized to develop a soft robot. However, this method introduces complications in the fabrication process as well as in further design flexibility and modifications. The current work presents a design scheme of a soft robotic actuator adapting an easier fabrication approach, which is economical and environment friendly as well. The purpose is the realization of a soft pneumatic actuator having functional ability to produce effective actuation, and which is further employable to develop modular and scalable mechanisms. That infers to scrutinize the profile and orientation of the internal actuation cavity and the outer shape of viii the actuator. Utilization of a single material for this actuator has been considered to make this design scheme convenient. A commercial silicone rubber was selected which served for an economical process both in terms of the cost as well as its accommodating fabrication process through molding. In order to obtain the material behavior, \u2018Ansys Workbench 17.1 R \u2019 has been used. Cubic outline for the actuator aided towards the realization of a body shape which can easily be engaged for the development of modular mechanisms employing multiple units. This outer body shape further facilitates to achieve the stability and portability of the actuator. The soft actuator has been named \u2018Soft Cubic Module\u2019 based on its external cubic shape. For the internal actuation cavity design, various shapes, such as spherical, elliptical and cylindrical, were examined considering their different sizes and orientations within the cubic module. These internal cavities were simulated in order to achieve single degree of freedom actuation. That means, only one face of the cube is principally required to produce effective deformation. \u2018Creo Perametric 3.0 M 130\u2019 has been used to design the model and to evaluate the performance of actuation cavities in terms of effective deformation and the resulting von-mises stress. Out of the simulated profiles, cylindrical cavity with desired outcomes has been further considered to design the soft actuator. \u2018Ansys Workbench 17.1 R \u2019 environment was further used to assess the performance of cylindrical actuation cavity. Evaluation in two different simulation environments helped to validate the initially achieved results. The developed soft cubic actuator was then employed to develop different mechanisms in a single unit configuration as well as multi-unit robotic system developments. This design scheme is considered as the first tool to investigate its capacity to perform certain given tasks in various configurations. Alongside its application as a single unit gripper and a two unit bio-mimetic crawling mechanism, this soft actuator has been employed to realize a four degree ix of freedom robotic mechanism. The formation of this primitive soft robotic four axis mechanism is being further considered to develop an equivalent mechanism similar to the well known Stewart platform, with advantages of compactness, simpler kinematics design, easier control, and lesser cost. Overall, the accomplished results indicate that the design scheme of Soft Cubic Module is helpful in realizing a simple and cost-effective soft pneumatic actuator which is modular and scalable. Another favourable point of this scheme is the use of a single material with convenient fabrication and handling

Design of a Mechatronic Interface with Compliant Manipulator for Robot Assisted Echocardiography

Abstract A compliant manipulator with a compound soft actuator is proposed for robot-assisted echocardiography. The target application is devoted to the TOE echo (Trans-oesophageal echocardiography), which is conventionally performed by medical practitioners. The manual manipulation of the echocardiography probe shows significant risks such as human errors, exposure to ionizing radiation, and multitasking complexity. Automation of TOE provides advantages in terms of control, safety, and workload of the operator. This paper proposes a teleoperated robotic system assisting the physician to perform TOE, to be used in cardiac catheterization laboratories as well as hybrid operation theatres. A system containing a holder with master-slave Dynamixel servos and a manipulator with soft actuators has been developed. To alleviate the major lack of the previous designs in conducting the insertion tube, a robotic arm with a soft structure is proposed that has not hazards of conventional robot manipulators. The fundamental equations and relations for quasi-static control of the system are developed in this paper