Energy harvesting for marine based sensors

This work examines powering marine based sensors (MBSs) by harvesting energy from their local environment. MBSs intrinsically operate in remote locations, traditionally requiring expensive maintenance expeditions for battery replacement and data download. Nowadays, modern wireless communication allows real-time data access, but adds a significant energy drain, necessitating frequent battery replacement. Harvesting renewable energy to recharge the MBSs battery, introduces the possibility of autonomous MBS operation, reducing maintenance costs and increasing their applicability. The thesis seeks to answer if an unobtrusive energy harvesting device can be incorporated into the MBS deployment to generate 1 Watt of average power. Two candidate renewable energy resources are identified for investigation, ocean waves and the thermal gradient across the air/water interface. Wave energy conversion has drawn considerable research in recent years, due to the large consistent energy flux of ocean waves compared to other conventional energy sources such as solar or wind, but focussing on large scale systems permanently deployed at sites targeted for their favourable wave climates. Although a small amount of research exists on using wave energy for distributed power generation, the device sizes and power outputs of these systems are still one to two orders of magnitude larger than that targeted in this thesis. The present work aims for an unobtrusive device that is easily deployable/retrievable with a mass less than 50kg and which can function at any deployment location regardless of the local wave climate. Additionally, this research differs from previous work, by also seeking to minimise the wave induced pitch motion of the MBS buoy, which negatively affects the data transmission of the MBS due to tilting and misalignment of the RF antenna. Thermal energy harvesting has previously been investigated for terrestrial based sensors, utilising the temperature difference between the soil and ambient air. In this thesis, the temperature difference between the water and ambient air is utilised, to present the first investigation of this thermal energy harvesting concept in the marine environment. A prototype wave energy converter (WEC) was proposed, consisting of a heaving cylindrical buoy with an internal permanent magnet linear generator. A mathematical model of the prototype WEC is derived by coupling a hydrodynamic model for the motion of the buoy with a vibration energy harvester model for the generator. The wave energy resource is assessed, using established mathematical descriptions of ocean wave spectra and by analysing measured wave data from the coast of Queensland, resulting in characteristic wave spectra that are input to the mathematical model of the WEC. The parameters of the WEC system are optimised, to maximise the power output while minimising the pitch motion. A prototype thermal energy harvesting device is proposed, consisting of a thermoelectric device sandwiched between airside and waterside heat exchangers. A mathematical model is derived to assess the power output of the thermal energy harvester using different environmental datasets as input. A physical prototype is built and a number of experiments performed to assess its performance. The results indicate that the prototype WEC should target the high frequency tail of ocean wave spectra, diverging from traditional philosophy of larger scale WECs which target the peak frequency of the input wave spectrum. The analysis showed that the prototype WEC was unable to provide the required power output whilst remaining below 100kg and obeying a 40 degrees pitch angle constraint to ensure robust data transmission. However, a proposed modification to the WECs cylindrical geometry, to improve its hydrodynamic coupling to the input waves, was shown to enable the WEC to provide the required 1W output power whilst obeying the pitch constraints and having a mass below 50kg. The thermal energy harvester results reveal that the thermal gradient across the air/water interface alone is not a suitable energy resource, requiring a device with a cross-sectional area in excess of 100m² to power a MBS. However, including a solar thermal energy collector to increase the airside temperature, greatly improves the performance and enables a thermal energy harvester with a cross-sectional area on the order of 1m² to provide 1W of output power. The findings in this thesis suggest that a well hydrodynamically designed buoy can provide two major benefits for a MBS deployment: enabling efficient wave energy absorption by the MBS buoy, and minimising the wave induced pitch motion which negatively affects the data transmission

Three-Tether Wave Energy Converter: Hydrodynamic Modelling, Performance Assessment and Control

Hydro, wind and solar power have become major contributors to the global renewable energy market. However, ocean wave power is emerging as a strong contender in the renewable energy mix due to its high power density and minimal environmental impact. Wave energy has the potential to provide an off-grid electricity solution to remote island communities, and fulfil offshore power needs of small industrial projects. One of the best wave energy resources in the world is concentrated along the southern margin of Australia, and if harnessed, wave power could contribute up to 27 per cent of the country’s electricity demand by 2050. Over the past few decades, a large number of concepts and designs have been suggested to convert wave energy into electricity. Despite a huge effort made by industry and the scientific community, the technology for extracting power from ocean waves still remains at a pre-commercial stage of development. The main challenge is to design an economically viable wave energy converter (WEC) where its life-cycle costs (investments, operation and maintenance) can be justified by the amount of generated electricity. This thesis focuses on the performance improvement of a particular class of wave energy converters, namely, a bottom-referenced fully submerged point absorber, by means of the three-tether mooring configuration. The main contribution is made towards the design, optimisation and control of the converter in order to answer three research questions: (i) what distinctive features of the fully submerged WECs can be utilised to increase their power absorption efficiency; (ii) how geometric parameters of the converter, such as the tether arrangement, shape, and aspect ratio affect the system performance; and (iii) what factors influence the practical implementation of the optimal control strategies on the three-tether WEC. To explore these questions, numerical frequency- and time-domain models have been developed using state-of-the-art techniques based on linear hydrodynamic theory. In order to gain background knowledge and build a core understanding of the submerged systems, the difference between floating and fully submerged point absorbers is investigated. Attention is given to the distinctive features observed in the hydrodynamic properties, power production limits, and control performance. Recommendations are provided on the choice of the buoy size and shape, depending on the wave climate of the deployment site. The advantages of employing multiple degrees of freedom in energy harvesting, especially for submerged converters, are demonstrated. The design considerations of the three-tether WEC are investigated from a number of perspectives including the tether arrangement, mass, shape, and aspect ratio of the buoy. A clear correlation between an optimal tether inclination angle and the buoy aspect ratio is identified. The comparison of three-tether WECs with different buoy geometries is performed not only based on their power output, but also taking into account a range of cost-related performance metrics. Moreover, the benefits of the three-tether converter over its single-tether counterpart are demonstrated through the detailed techno-economic analysis of both prototypes. The final aspect of this dissertation is devoted to the development of the advanced control system for the three-tether WEC. The causal velocity tracking controller is taken as a basis and extended to the multivariable control problem. It is demonstrated that the designed controller is able to improve the power absorption of the three-tether WEC as compared to a quasi-standard control approach while imposing a series of technical requirements on the power take-off machinery.Thesis (Ph.D.) -- University of Adelaide, School of Mechanical Engineering, 201

Control of Ocean Wave Energy Converters with Finite Stroke

In the design of ocean wave energy converters, proper control design is essential for the maximization of power generation performance. However, in practical applications, this control must be undertaken in the presence of stroke saturation and model uncertainty. In this dissertation, we address these challenges separately. To address stroke saturation, a nonlinear control design procedure is proposed, which guarantees to keep the stroke within its limits. The technique exploits the passivity of the wave energy converter to guarantee closed-loop stability. The proposed technique consists of three steps: 1) design of a linear feedback controller using multi-objective optimization techniques; 2) augmentation of this design with an extra input channel that adheres to a closed-loop passivity condition; and 3) design of an outer, nonlinear passive feedback loop that controls this augmented input in such a way as to ensure stroke limits are maintained. The discrete-time version of this technique is also presented. To address model uncertainty, in particular we consider the nonlinear viscosity drag effect as the model uncertainty. This robust control design problem can be regarded as a multi-objective optimization problem, whose primary objective is to optimize the nominal performance, while the second objective is to robustly stabilize the closed-loop system. The robust stability constraint can be posed using the concept of circle criterion. Because this optimization is non-convex, Loop Transfer Recovery methods are used to solve for sub-optimal solutions to the problem. These techniques are demonstrated in simulation, for arrays of buoy-type wave energy converters.PHDCivil EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/163263/1/waynelao_1.pd

Aeronautical engineering: A continuing bibliography with indexes (supplement 293)

This bibliography lists 476 reports, articles, and other documents introduced into the NASA scientific and technical information system in July, 1992. Subject coverage includes: design, construction and testing of aircraft and aircraft engines; aircraft components, equipment, and systems; ground support systems; and theoretical and applied aspects of aerodynamics and general fluid dynamics

Design, validation and application of wave-to-wire models for heaving point absorber wave energy converters

Ocean waves represent an untapped source of renewable energy which can significantly contribute to the energy transition towards a sustainable energy mix. Despite the significant potential of this energy source and the multiple solutions suggested for the extraction of energy from ocean waves, some of which have demonstrated to be technically viable, no commercial wave energy farm has yet been connected to the electricity grid. This means that none of the technologies suggested in the literature has achieved economic viability. In order to make wave energy converters economically viable, it is essential to accurately understand and evaluate the holistic behaviour and performance of wave energy converters, including all the different conversion stages from ocean waves to the electricity grid. This can be achieved through wave tank or open ocean testing campaigns, which are extremely expensive and, thus, can critically determine the financial sustainability of the developing organisation, due to the risk of such large investments. Therefore, precise mathematical models that consider all the important dynamics, losses and constraints of the different conversion stages (including wave-structure hydrodynamic interaction and power take-off system), known as wave-to-wire models, are crucial in the development of successful wave energy converters. Hence, a comprehensive literature review of the different mathematical approaches suggested for modelling the different conversion stages and existing wave-to-wire models is presented, defining the foundations of parsimonious wave-to-wire models and their potential applications. As opposed to other offshore applications, wave energy converters need to exaggerate their motion to maximise energy absorption from ocean waves, which breaks the assumption of small body motion upon which linear models are based. An extensive investigation on the suitability of linear models and the relevance of different nonlinear effects is carried out, where control conditions are shown to play an important role. Hence, a computationally efficient mathematical model that incorporates nonlinear Froude-Krylov forces and viscous effects is presented. In the case of the power take-off system, mathematical models for different hydraulic transmission system configurations and electric generator topologies are presented, where the main losses are included using specific loss models with parameters identified via manufacturers’ data. In order to gain confidence in the mathematical models, the models corresponding to the different conversion stages are validated separately against either high-fidelity well-established software or experimental results, showing very good agreement. The main objective of this thesis is the development of a comprehensive wave-to-wire model. This comprehensive wave-to-wire model is created by adequately combining the subsystems corresponding to the different components or conversion stages. However, time-step requirements vary significantly depending on the dynamics included in each subsystem. Hence, if the time-step required for capturing the fastest dynamics is used in all the subsystems, unnecessary computation is performed in the subsystems with slower dynamics. Therefore, a multi-rate time-integration scheme is implemented, meaning that each subsystem uses the sample period required to adequately capture the dynamics of the components included in that conversion stage, which significantly reduces the overall computational requirements. In addition, the relevance of using a high-fidelity comprehensive wave-to-wire model in accurately designing wave energy converters and assessing their capabilities is demonstrated. For example, energy maximising controllers based on excessively simplified mathematical models result in dramatic consequences, such as negative average generated power or situations where the device remains stuck at one of the end-stops of the power take-off system. Despite the reasonably high-fidelity of the results provided by this comprehensive wave-towire model, some applications require the highest possible fidelity level and have no limitation with respect to computational cost. Hence, the simulation platform HiFiWEC, which couples a numerical wave tank based on computational fluid dynamics to the high-fidelity power take-off model, is created. In contrast, low computational cost is the main requirement for other applications and, thus, a systematic complexity reduction approach is suggested in this thesis, significantly reducing the computational cost of the HiFiWEC platform, while retaining the adequate fidelity level for each application. Due to the relevance of the nonlinearity degree when evaluating the complexity of a mathematical model, two nonlinearity measures to quantify this nonlinearity degree are defined. Hence, wave-to-wire models specifically created for each application are generated via the systematic complexity reduction approach, which provide the adequate trade-off between computational cost and fidelity level required for each application

Bibliography of Lewis Research Center technical publications announced in 1987

This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1987. All the publications were announced in the 1987 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses

Bibliography of Lewis Research Center technical publications announced in 1992

This compilation of abstracts describes and indexes the technical reporting that resulted from the scientific and engineering work performed and managed by the Lewis Research Center in 1992. All the publications were announced in the 1992 issues of STAR (Scientific and Technical Aerospace Reports) and/or IAA (International Aerospace Abstracts). Included are research reports, journal articles, conference presentations, patents and patent applications, and theses

Aeronautical Engineering, a continuing bibliography with indexes

This bibliography lists 546 reports, articles and other documents introduced into the NASA scientific and technical information system in October 1984

Aeronautical engineering: A continuing bibliography with indexes (supplement 295)

This bibliography lists 581 reports, articles, and other documents introduced into the NASA Scientific and Technical Information System in Sep. 1993. Subject coverage includes: design, construction and testing of aircraft and aircraft engines; aircraft components, equipment, and systems; ground support systems; and theoretical and applied aspects of aerodynamics and general fluid dynamics