High Efficiency Power Amplifier Based on Envelope Elimination and Restoration Technique

Due to complex envelope and phase modulation employed in modern transmitters it is necessary to use power amplifiers that have high linearity. Linear power amplifiers (classes A, B and AB) are commonly used, but they suffer from low efficiency especially if the transmitted signal has high peak to average power ratio (PAPR). Kahn's technique based on envelope elimination and restoration (EER) is based on idea that high efficiency power supply (envelope amplifier) could be used to modulate the envelope of high efficient non linear power amplifiers (classes D or E). This paper presents solutions for power amplifier that performs envelope modulation and class E amplifier that is used as a non linear amplifier. The envelope amplifier is implemented as a multilevel converter in series with linear regulator and can provide up to 100 W of instantaneous power and reproduce 2 MHz sine wave. The implemented Class E amplifier can operate at 120 MHz with efficiency near to 85%. The envelope amplifier and class E amplifier have been integrated and efficiency and linearity of the implemented transmitter has been measured and presente

A 24-GHz, +14.5-dBm fully integrated power amplifier in 0.18-μm CMOS

A 24-GHz +14.5-dBm fully integrated power amplifier with on-chip 50-[ohm] input and output matching is demonstrated in 0.18-μm CMOS. The use of substrate-shielded coplanar waveguide structures for matching networks results in low passive loss and small die size. Simple circuit techniques based on stability criteria derived result in an unconditionally stable amplifier. The power amplifier achieves a power gain of 7 dB and a maximum single-ended output power of +14.5-dBm with a 3-dB bandwidth of 3.1 GHz, while drawing 100 mA from a 2.8-V supply. The chip area is 1.26 mm^2

Third-order Intermodulation Reduction in Mobile Power Amplifiers by the First Stage Bias Control

In this paper, the third order intermodulation distortion (IMD3) of three-stage power amplifier (PA) is analyzed using the Volterra series. The analysis explains how the total IMD3 of the three-stage power amplifier can be reduced by the first-stage bias condition. The three-stage PA, which is fabricated using InGaP/GaAs hetero-junction bipolar transistor (HBT), operates with an optimized first driver stage bias for higher P1dB and good gain flatness. The power amplifier has been designed for 1626.5 MHz~1660.5 MHz satellite mobile communications. With π/4 DQPSK modulation signals, this PA can deliver a highly linear output power of 33 dBm from 3.6V supply voltage. At 33 dBm output power, it shows a gain of 31.9 dB, a power-added efficiency (PAE) of 39.8%, an adjacent channel power ratio (ACPR) of -28.2 dBc at a 31.25 KHz offset frequency

A 1-W, 30-ghz, CPW Amplifier for ACTS Small Terminal Uplink

The progress is described of the development of a 1 W, 30 GHz, coplanar waveguide (CPW) amplifier for the Advanced Communication Technology Satellite (ACTS)Small Terminal Uplink. The amplifier is based on Texas Instruments' monolithic microwave integrated circuit (MMIC) amplifiers; a three stage, low power amplifier, and a single stage, high power amplifier. The amplifiers have a power output of 190 mW and 0.710 W, gain of 23 and 4.2 dB, and efficiencies of 30.2 and 24 percent for the three stage and one stage amplifiers, respectively. The chips are to be combined via a CPW power divider/combiner circuit to yield the desired 1 W of output power

Space Power Amplification with Active Linearly Tapered Slot Antenna Array

A space power amplifier composed of active linearly tapered slot antennas (LTSA's) has been demonstrated and shown to have a gain of 30 dB at 20 GHz. In each of the antenna elements, a GaAs monolithic microwave integrated circuit (MMIC) three-stage power amplifier is integrated with two LTSA's. The LTSA and the MMIC power amplifier has a gain of 11 dB and power added efficiency of 14 percent respectively. The design is suitable for constructing a large array using monolithic integration techniques

Efficiency of low power audio amplifiers and loudspeakers

In this paper we look at the load presented to audio amplifiers by real transducers. We consider the power losses in Class-AB and Class-D amplifier topologies, and determine that in order to predict efficiency it is necessary to consider the amplifier/transducer combination. The ability of the class-D amplifier to recycle quadrature load current offers new ways to improve efficiency

Fully integrated CMOS power amplifier design using the distributed active-transformer architecture

A novel on-chip impedance matching and power-combining method, the distributed active transformer is presented. It combines several low-voltage push-pull amplifiers efficiently with their outputs in series to produce a larger output power while maintaining a 50-Ω match. It also uses virtual ac grounds and magnetic couplings extensively to eliminate the need for any off-chip component, such as tuned bonding wires or external inductors. Furthermore, it desensitizes the operation of the amplifier to the inductance of bonding wires making the design more reproducible. To demonstrate the feasibility of this concept, a 2.4-GHz 2-W 2-V truly fully integrated power amplifier with 50-Ω input and output matching has been fabricated using 0.35-μm CMOS transistors. It achieves a power added efficiency (PAE) of 41 % at this power level. It can also produce 450 mW using a 1-V supply. Harmonic suppression is 64 dBc or better. This new topology makes possible a truly fully integrated watt-level gigahertz range low-voltage CMOS power amplifier for the first time

Linear transmitter design for MSAT terminals

One of the factors that will undoubtedly influence the choice of modulation format for mobile satellites, is the availability of cheap, power-efficient, linear amplifiers for mobile terminal equipment operating in the 1.5-1.7 GHz band. Transmitter linearity is not easily achieved at these frequencies, although high power (20W) class A/AB devices are becoming available. However, these components are expensive and require careful design to achieve a modest degree of linearity. In this paper an alternative approach to radio frequency (RF) power amplifier design for mobile satellite (MSAT) terminals using readily-available, power-efficient, and cheap class C devices in a feedback amplifier architecture is presented