On Coding and Detection Techniques for Two-Dimensional Magnetic Recording

Edited version embargoed until 15.04.2020 Full version: Access restricted permanently due to 3rd party copyright restrictions. Restriction set on 15/04/2019 by AS, Doctoral CollegeThe areal density growth of magnetic recording systems is fast approaching the superparamagnetic limit for conventional magnetic disks. This is due to the increasing demand for high data storage capacity. Two-dimensional Magnetic Recording (TDMR) is a new technology aimed at increasing the areal density of magnetic recording systems beyond the limit of current disk technology using conventional disk media. However, it relies on advanced coding and signal processing techniques to achieve areal density gains. Current state of the art signal processing for TDMR channel employed iterative decoding with Low Density Parity Check (LDPC) codes, coupled with 2D equalisers and full 2D Maximum Likelihood (ML) detectors. The shortcoming of these algorithms is their computation complexity especially with regards to the ML detectors which is exponential with respect to the number of bits involved. Therefore, robust low-complexity coding, equalisation and detection algorithms are crucial for successful future deployment of the TDMR scheme. This present work is aimed at finding efficient and low-complexity coding, equalisation, detection and decoding techniques for improving the performance of TDMR channel and magnetic recording channel in general. A forward error correction (FEC) scheme of two concatenated single parity bit systems along track separated by an interleaver has been presented for channel with perpendicular magnetic recording (PMR) media. Joint detection decoding algorithm using constrained MAP detector for simultaneous detection and decoding of data with single parity bit system has been proposed. It is shown that using the proposed FEC scheme with the constrained MAP detector/decoder can achieve a gain of up to 3dB over un-coded MAP decoder for 1D interference channel. A further gain of 1.5 dB was achieved by concatenating two interleavers with extra parity bit when data density along track is high. The use of single bit parity code as a run length limited code as well as an error correction code is demonstrated to simplify detection complexity and improve system performance. A low-complexity 2D detection technique for TDMR system with Shingled Magnetic Recording Media (SMR) was also proposed. The technique used the concatenation of 2D MAP detector along track with regular MAP detector across tracks to reduce the complexity order of using full 2D detection from exponential to linear. It is shown that using this technique can improve track density with limited complexity. Two methods of FEC for TDMR channel using two single parity bit systems have been discussed. One using two concatenated single parity bits along track only, separated by a Dithered Relative Prime (DRP) interleaver and the other use the single parity bits in both directions without the DRP interleaver. Consequent to the FEC coding on the channel, a 2D multi-track MAP joint detector decoder has been proposed for simultaneous detection and decoding of the coded single parity bit data. A gain of up to 5dB was achieved using the FEC scheme with the 2D multi-track MAP joint detector decoder over un-coded 2D multi-track MAP detector in TDMR channel. In a situation with high density in both directions, it is shown that FEC coding using two concatenated single parity bits along track separated by DRP interleaver performed better than when the single parity bits are used in both directions without the DRP interleaver.9mobile Nigeri

Interior Point Decoding for Linear Vector Channels

In this paper, a novel decoding algorithm for low-density parity-check (LDPC) codes based on convex optimization is presented. The decoding algorithm, called interior point decoding, is designed for linear vector channels. The linear vector channels include many practically important channels such as inter symbol interference channels and partial response channels. It is shown that the maximum likelihood decoding (MLD) rule for a linear vector channel can be relaxed to a convex optimization problem, which is called a relaxed MLD problem. The proposed decoding algorithm is based on a numerical optimization technique so called interior point method with barrier function. Approximate variations of the gradient descent and the Newton methods are used to solve the convex optimization problem. In a decoding process of the proposed algorithm, a search point always lies in the fundamental polytope defined based on a low-density parity-check matrix. Compared with a convectional joint message passing decoder, the proposed decoding algorithm achieves better BER performance with less complexity in the case of partial response channels in many cases.Comment: 18 pages, 17 figures, The paper has been submitted to IEEE Transaction on Information Theor

새로운 소실 채널을 위한 자기동형 군 복호기 및 부분 접속 복구 부호 및 일반화된 근 프로토그래프 LDPC 부호의 설계

학위논문 (박사)-- 서울대학교 대학원 : 공과대학 전기·컴퓨터공학부, 2019. 2. 노종선.In this dissertation, three main contributions are given asi) new two-stage automorphism group decoders (AGD) for cyclic codes in the erasure channel, ii) new constructions of binary and ternary locally repairable codes (LRCs) using cyclic codes and existing LRCs, and iii) new constructions of high-rate generalized root protograph (GRP) low-density parity-check (LDPC) codes for a nonergodic block interference and partially regular (PR) LDPC codes for follower noise jamming (FNJ), are considered. First, I propose a new two-stage AGD (TS-AGD) for cyclic codes in the erasure channel. Recently, error correcting codes in the erasure channel have drawn great attention for various applications such as distributed storage systems and wireless sensor networks, but many of their decoding algorithms are not practical because they have higher decoding complexity and longer delay. Thus, the AGD for cyclic codes in the erasure channel was introduced, which has good erasure decoding performance with low decoding complexity. In this research, I propose new TS-AGDs for cyclic codes in the erasure channel by modifying the parity check matrix and introducing the preprocessing stage to the AGD scheme. The proposed TS-AGD is analyzed for the perfect codes, BCH codes, and maximum distance separable (MDS) codes. Through numerical analysis, it is shown that the proposed decoding algorithm has good erasure decoding performance with lower decoding complexity than the conventional AGD. For some cyclic codes, it is shown that the proposed TS-AGD achieves the perfect decoding in the erasure channel, that is, the same decoding performance as the maximum likelihood (ML) decoder. For MDS codes, TS-AGDs with the expanded parity check matrix and the submatrix inversion are also proposed and analyzed. Second, I propose new constructions of binary and ternary LRCs using cyclic codes and existing two LRCs for distributed storage system. For a primitive work, new constructions of binary and ternary LRCs using cyclic codes and their concatenation are proposed. Some of proposed binary LRCs with Hamming weights 4, 5, and 6 are optimal in terms of the upper bounds. In addition, the similar method of the binary case is applied to construct the ternary LRCs with good parameters. Also, new constructions of binary LRCs with large Hamming distance and disjoint repair groups are proposed. The proposed binary linear LRCs constructed by using existing binary LRCs are optimal or near-optimal in terms of the bound with disjoint repair group. Last, I propose new constructions of high-rate GRP LDPC codes for a nonergodic block interference and anti-jamming PR LDPC codes for follower jamming. The proposed high-rate GRP LDPC codes are based on nonergodic two-state binary symmetric channel with block interference and Nakagami-$m$ block fading. In these channel environments, GRP LDPC codes have good performance approaching to the theoretical limit in the channel with one block interference, where their performance is shown by the channel threshold or the channel outage probability. In the proposed design, I find base matrices using the protograph extrinsic information transfer (PEXIT) algorithm. Also, the proposed new constructions of anti-jamming partially regular LDPC codes is based on follower jamming on the frequency-hopped spread spectrum (FHSS). For a channel environment, I suppose follower jamming with random dwell time and Rayleigh block fading environment with M-ary frequnecy shift keying (MFSK) modulation. For a coding perspective, an anti-jamming LDPC codes against follower jamming are introduced. In order to optimize the jamming environment, the partially regular structure and corresponding density evolution schemes are used. A series of simulations show that the proposed codes outperforms the 802.16e standard in the presence of follower noise jamming.이 논문에서는, i) 소실 채널에서 순환 부호의 새로운 이단 자기동형 군 복호기 , ii) 분산 저장 시스템을 위한 순환 부호 및 기존의 부분 접속 복구 부호(LRC)를 이용한 이진 혹은 삼진 부분 접속 복구 부호 설계법, 및 iii) 블록 간섭 환경을 위한 고부효율의 일반화된 근 프로토그래프(generalized root protograph, GRP) LDPC 부호 및 추적 재밍 환경을 위한 항재밍 부분 균일 (anti-jamming paritally regular, AJ-PR) LDPC 부호가 연구되었다. 첫번째로, 소실 채널에서 순환 부호의 새로운 이단 자기동형 군 복호기를 제안하였다. 최근 분산 저장 시스템 혹은 무선 센서 네트워크 등의 응용으로 인해 소실 채널에서의 오류 정정 부호 기법이 주목받고 있다. 그러나 많은 복호기 알고리즘은 높은 복호 복잡도 및 긴 지연으로 인해 실용적이지 못하다. 따라서 낮은 복호 복잡도 및 높은 성능을 보일 수 있는 순환 부호에서 이단 자기 동형 군 복호기가 제안되었다. 본 연구에서는 패리티 검사 행렬을 변형하고, 전처리 과정을 도입한 새로운 이단 자기동형 군 복호기를 제안한다. 제안한 복호기는 perfect 부호, BCH 부호 및 최대 거리 분리 (maximum distance separable, MDS) 부호에 대해서 분석되었다. 수치 분석을 통해, 제안된 복호 알고리즘은 기존의 자기 동형 군 복호기보다 낮은 복잡도를 보이며, 몇몇의 순환 부호 및 소실 채널에서 최대 우도 (maximal likelihood, ML)과 같은 수준의 성능임을 보인다. MDS 부호의 경우, 확장된 패리티검사 행렬 및 작은 크기의 행렬의 역연산을 활용하였을 경우의 성능을 분석한다. 두 번째로, 분산 저장 시스템을 위한 순환 부호 및 기존의 부분 접속 복구 부호 (LRC)를 이용한 이진 혹은 삼진 부분 접속 복구 부호 설계법을 제안하였다. 초기 연구로서, 순환 부호 및 연접을 활용한 이진 및 삼진 LRC 설계 기법이 연구되었다. 최소 해밍 거리가 4,5, 혹은 6인 제안된 이진 LRC 중 일부는 상한과 비교해 보았을 때 최적 설계임을 증명하였다. 또한, 비슷한 방법을 적용하여 좋은 파라미터의 삼진 LRC를 설계할 수 있었다. 그 외에 기존의 LRC를 활용하여 큰 해밍 거리의 새로운 LRC를 설계하는 방법을 제안하였다. 제안된 LRC는 분리된 복구 군 조건에서 최적이거나 최적에 가까운 값을 보였다. 마지막으로, GRP LDPC 부호는 Nakagami-$m$ 블록 페이딩 및 블록 간섭이 있는 두 상태의 이진 대칭 채널을 기반으로 한다. 이러한 채널 환경에서 GRP LDPC 부호는 하나의 블록 간섭이 발생했을 경우, 이론적 성능에 가까운 좋은 성능을 보여준다. 이러한 이론 값은 채널 문턱값이나 채널 outage 확률을 통해 검증할 수 있다. 제안된 설계에서는, 변형된 PEXIT 알고리즘을 활용하여 기초 행렬을 설계한다. 또한 AJ-PR LDPC 부호는 주파수 도약 환경에서 발생하는 추적 재밍이 있는 환경을 기반으로 한다. 채널 환경으로 MFSK 변복조 방식의 레일리 블록 페이딩 및 무작위한 지속 시간이 있는 재밍 환경을 가정한다. 이러한 재밍 환경으로 최적화하기 위해, 부분 균일 구조 및 해당되는 밀도 진화 (density evolution, DE) 기법이 활용된다. 여러 시뮬레이션 결과는 추적 재밍이 존재하는 환경에서 제안된 부호가 802.16e에 사용되었던 LDPC 부호보다 성능이 우수함을 보여준다.Contents Abstract Contents List of Tables List of Figures 1 INTRODUCTION 1.1 Background 1.2 Overview of Dissertation 1.3 Notations 2 Preliminaries 2.1 IED and AGD for Erasure Channel 2.1.1 Iterative Erasure Decoder 2.1.1 Automorphism Group Decoder 2.2. Binary Locally Repairable Codes for Distributed Storage System 2.2.1 Bounds and Optimalities of Binary LRCs 2.2.2 Existing Optimal Constructions of Binary LRCs 2.3 Channels with Block Interference and Jamming 2.3.1 Channels with Block Interference 2.3.2 Channels with Jamming with MFSK and FHSS Environment. 3 New Two-Stage Automorphism Group Decoders for Cyclic Codes in the Erasure Channel 3.1 Some Definitions 3.2 Modification of Parity Check Matrix and Two-Stage AGD 3.2.1 Modification of the Parity Check Matrix 3.2.2 A New Two-Stage AGD 3.2.3 Analysis of Modification Criteria for the Parity Check Matrix 3.2.4 Analysis of Decoding Complexity of TS-AGD 3.2.5 Numerical Analysis for Some Cyclic Codes 3.3 Construction of Parity Check Matrix and TS-AGD for Cyclic MDS Codes 3.3.1 Modification of Parity Check Matrix for Cyclic MDS Codes . 3.3.2 Proposed TS-AGD for Cyclic MDS Codes 3.3.3 Perfect Decoding by TS-AGD with Expanded Parity Check Matrix for Cyclic MDS Codes 3.3.4 TS-AGD with Submatrix Inversion for Cyclic MDS Codes . . 4 New Constructions of Binary and Ternary LRCs Using Cyclic Codes and Existing LRCs 4.1 Constructions of Binary LRCs Using Cyclic Codes 4.2 Constructions of Linear Ternary LRCs Using Cyclic Codes 4.3 Constructions of Binary LRCs with Disjoint Repair Groups Using Existing LRCs 4.4 New Constructions of Binary Linear LRCs with d ≥ 8 Using Existing LRCs 5 New Constructions of Generalized RP LDPC Codes for Block Interference and Partially Regular LDPC Codes for Follower Jamming 5.1 Generalized RP LDPC Codes for a Nonergodic BI 5.1.1 Minimum Blockwise Hamming Weight 5.1.2 Construction of GRP LDPC Codes 5.2 Asymptotic and Numerical Analyses of GRP LDPC Codes 5.2.1 Asymptotic Analysis of LDPC Codes 5.2.2 Numerical Analysis of Finite-Length LDPC Codes 5.3 Follower Noise Jamming with Fixed Scan Speed 5.4 Anti-Jamming Partially Regular LDPC Codes for Follower Noise Jamming 5.4.1 Simplified Channel Model and Corresponding Density Evolution 5.4.2 Construction of AJ-PR-LDPC Codes Based on DE 5.5 Numerical Analysis of AJ-PR LDPC Codes 6 Conclusion Abstract (In Korean)Docto

Bacon-Shor code with continuous measurement of non-commuting operators

We analyze the operation of a four-qubit Bacon-Shor code with simultaneous continuous measurement of non-commuting gauge operators. The error syndrome in this case is monitored via time-averaged cross-correlators of the output signals. We find the logical error rate for several models of decoherence, and also find the termination rate for this quantum error detecting code. The code operation is comparable to that based on projective measurements when the collapse timescale due to continuous measurements is an order of magnitude less than the time period between the projective measurements. An advantage of the continuous-measurement implementation is the absence of time-dependence in the code operation, with passive continuous monitoring of the error syndrome.Comment: 25 pages, 8 figure