Chemical Vapor Deposition of silicon nanodots on TiO2 submicronic powders in vibrated fluidized bed

Silicon nanodots have been deposited on TiO2 submicronic powders in a vibrated Fluidized Bed Chemical Vapor Deposition (FBCVD) reactor from silane SiH4. Deposition conditions involving very low deposition rates have been studied. After treatment, powders are under the form of micronic agglomerates. In the operating range tested, this agglomerates formation mainly depends on the fluidization conditions and not on the CVD parameters. The best results have been obtained for anatase TiO2 powders for which the conditions of fluidization have been the most optimized. For these anatase powders, agglomerates are porous. SEM and TEM imaging prove that silicon nanodots (8-10 nm in size) have been deposited on the surface of particles and that this deposition is uniform on the whole powders and conformal around each grain, even if not fully continuous. Raman spectroscopy shows that the TiO2 powders have been partially reduced into TiO2-x during deposition. The TiO2 stoichiometry can be recovered by annealing under air, and IR spectroscopy indicates that the deposited silicon nanodots have been at least partly oxidized into SiO2 after this annealing

An attempt to obtain Bi_{4}Ti_{3}O_{12}-PVC textured ceramics-polymer composites

Bi_{4}Ti_{3}O_{12}-PVC composites were fabricated. Ceramics powders of bismuth titanate were prepared by the sol-gel method using bismuth nitrate pentahydrate Bi(NO_{3})_{3} \cdot 5H_{2}O and tetrabutyl titanate Ti(CH_{3}(CH_{2})_{3}O)_{4} as precursors. The Bi_{4}Ti_{3}O_{12}-PVC composites were fabricated from ceramics powders and polymer powders by hot-pressing method.Comment: 4 pages, 4 figure

Defining Temperatures of Granular Powders Analogously with Thermodynamics to Understand the Jamming Phenomena

For the purpose of applying laws or principles originated from thermal systems to granular athermal systems, we may need to properly define the critical temperature concept in granular powders. The conventional environmental temperature in thermal systems is too weak to drive movements of particles in granular powders and cannot function as a thermal energy indicator. For maintaining the same functionality as in thermal systems, the temperature in granular powders is defined analogously and uniformly in this article. The newly defined granular temperature is utilized to describe and explain one of the most important phenomena observed in granular powders, the jamming transition, by introducing jamming temperature and jamming volume fraction concepts. The predictions from the equations of the jamming volume fractions for several cases like granular powders under shear or vibration are in line with experimental observations and empirical solutions in powder handlings. The goal of this article is to establish similar concepts in granular powders, allowing granular powders to be described with common laws or principles we are familiar with in thermal systems. Our intention is to build a bridge between thermal systems and granular powders to account for many similarities already found between these two systems.Comment: 34 pages,15 figure

Catalytic chemical vapor deposition synthesis of single- and double-walled carbon nanotubes from α-(Al1−xFex)2O3 powders and self-supported foams

An investigation of the potential interest of α-alumina–hematite foams, as opposed to powders, as starting materials for the synthesis of carbon nanotubes (CNTs) by catalytic chemical vapor deposition method was performed. The oxide powders and foams as well as the corresponding CNT–Fe–Al2O3 composite powders and foams are studied by X-ray diffraction, specific surface area measurements, electron microscopy, Raman spectroscopy and Mössbauer spectroscopy. The latter technique revealed that four components (corresponding to α-Fe, Fe3C, γ-Fe-C and Fe3+) were present in the Mössbauer spectra of the composite powders, and that an additional sextet, possibly due to an Fe1−yCy alloy, is also present in the Mössbauer spectra of the composite foams. Contrary to some expectations, using foams do not lead to an easier reduction and thus to the formation of more α-Fe, Fe3C and/or γ-Fe–C potentially active particles for the formation of CNTs, and hence to no gain in the quantity of CNTs. However, using foams as starting materials strongly favors the selectivity of the method towards SWCNTs (60% SWCNTs and 40% DWCNTs) compared to what is obtained using powders (5% SWCNTs, 65% DWCNTs and 30% MWCNTs)

Improved retort for cleaning metal powders with hydrogen

Improved cleaning retort produces uniform temperature distribution in the heated zone and minimizes hydrogen channeling through the powder bed. Retort can be used for nonmetallic powders, sintering in a reducing atmosphere, and for cleaning powders in reduction atmospheres other than hydrogen

Nano-scale analysis of titanium dioxide fingerprint-development powders

Titanium dioxide based powders are regularly used in the development of latent fingerprints on dark surfaces. For analysis of prints on adhesive tapes, the titanium dioxide is suspended in a surfactant and used in the form of a small particle reagent (SPR). Analysis of commercially available products shows varying levels of effectiveness of print development, with some powders adhering to the background as well as the print. Scanning electron microscopy (SEM) images of prints developed with different powders show a range of levels of aggregation of particles. Analytical transmission electron microscopy (TEM) of the fingerprint powder shows TiO2 particles with a surrounding coating, tens of nanometres thick, consisting of Al and Si rich material. X ray photoelectron spectroscopy (XPS) is used to determine the composition and chemical state of the surface of the powders; with a penetration depth of approximately 10nm, this technique demonstrates differing Ti: Al: Si ratios and oxidation states between the surfaces of different powders. Levels of titanium detected with this technique demonstrate variation in the integrity of the surface coating. The thickness, integrity and composition of the Al/Si-based coating is related to the level of aggregation of TiO2 particles and efficacy of print development

The spectroscopic detection of drugs of abuse in fingerprints after development with powders and recovery with adhesive lifters

The application of powders to fingerprints has long been established as an effective and reliable method for developing latent fingerprints. Fingerprints developed in situ at a crime scene routinely undergo lifting with specialist tapes and are then stored in evidence bags to allow secure transit and also to preserve the chain of evidence. In a previous study we have shown that exogenous material within a fingerprint can be detected using Raman spectroscopy following development with powders and lifting with adhesive tapes. Other reports have detailed the use of Raman spectroscopy to the detection of drugs of abuse in latent fingerprints including cyanoacrylate-fumed fingerprints. This study involves the application of Raman spectroscopy for the analysis of drugs of abuse in latent fingerprints for fingerprints that had been treated with powders and also subsequently lifted with adhesive tapes. Samples of seized ecstasy, cocaine, ketamine and amphetamine were supplied by East Sussex Police and by the TICTAC unit at St. Georges Hospital Tooting. Contaminated fingerprintswere deposited on clean glass slides. The application of aluminium or iron based powders to contaminated fingerprints did not interfere with theRamanspectra obtained for the contaminants. Contaminated fingerprints developed with powders and then lifted with lifting tapes were also examined. The combination of these two techniques did not interfere with the successful analysis. The lifting processwas repeated using hinge lifters. As the hinge lifters exhibited strong Raman bands the spectroscopic analysiswas more complex and an increase in the number of exposures to the detector allowed for improved clarification. Spectral subtraction was performed to remove peaks due to the hinge lifters using OMNIC software. Raman spectra of developed and lifted fingerprints recorded through evidence bags were obtained and it was found that the detection process was not compromised. Although the application of powders did not interfere with the detection process the time taken to locate the contaminant was increased due to the physical presence of more material within the fingerprint

The Measurement of the Thermal Properties and Absorptances of Powders Near their Melting Temperatures

A new technique, using a laser as the heating source, has been adopted to measure the heat capacities, thermal diffusivities, thermal conductivities, and absorptances of powders (especially polymer powders) near their melting temperatures. This makes use of an unsteady state process. The data of the thermal conductivities obtained through this technique below 100°C are in concord with the values obtained through the other techniques, which predicts well for the use of this technique for still higher temperatures, up to the melting temperatures of the powders to be investigated.Mechanical Engineerin

Synthesis by sol–gel route of oxyapatite powders for dense ceramics : applications as electrolytes for solid oxide fuel cells

Solid oxide fuel cells have considerable interest in recent years, because of their high efficiency and environmentally friendly nature. Such systems required oxygen-conducting electrolytes and now the most common electrolyte is yttria stabilized zirconia (YSZ). This compound exhibits high oxide ion conductivity at elevated temperatures (850–1000 °C). However, this high working temperature causes problems in terms of materials selection and lifetime. One solution is to develop new oxide ions conductors exhibiting high oxide ion conductivity at intermediary temperatures (700–800 °C). Recent work has identified Ln10−xSi6O26±z (Ln = rare earths) as a good fast oxide ion conductor. Undoped and doped Ln10−xB6O26±z (B = Si or Ge) oxides are currently prepared by solid-state methods. In that work, we propose a sol–gel process to synthesize powders of La9.33Si6O26 type-silicated apatites. The main advantage is to decrease the crystallization temperature in ,comparison to the conventional methods, allowing the synthesis of reactive powders with nanometric particles size. These oxides are synthesized using silicon alkoxide and lanthanum nitride as precursors. In the litterature, no study refers to the synthesis of mixed oxides with silicon alcoxides. However, there are several studies on sol–gel synthesis of glasses with this precursor. In this study, several processing parameters have been investigated (the hydrolysis ratio, the concentration of metallic precursors in the sol and the role of organic compounds) in order to synthesize pure phases after the decomposition of the sols. Pure powders of La9.33Si6O26 type-silicated apatites are obtained at 800 °C. These powders were used to prepare ceramics. Several processing parameters as morphology of powders (agglomeration, particle sizes) and, heating profiles have been studied on the densification. Dense ceramics (90–95%) have been prepared at temperatures around 1400 °C. The used of sol–gel powders allow the decrease of the sintering temperature of about 200 °C