Oscillation-based DFT for Second-order Bandpass OTA-C Filters

This document is the Accepted Manuscript version. Under embargo until 6 September 2018. The final publication is available at Springer via https://doi.org/10.1007/s00034-017-0648-9.This paper describes a design for testability technique for second-order bandpass operational transconductance amplifier and capacitor filters using an oscillation-based test topology. The oscillation-based test structure is a vectorless output test strategy easily extendable to built-in self-test. The proposed methodology converts filter under test into a quadrature oscillator using very simple techniques and measures the output frequency. Using feedback loops with nonlinear block, the filter-to-oscillator conversion techniques easily convert the bandpass OTA-C filter into an oscillator. With a minimum number of extra components, the proposed scheme requires a negligible area overhead. The validity of the proposed method has been verified using comparison between faulty and fault-free simulation results of Tow-Thomas and KHN OTA-C filters. Simulation results in 0.25μm CMOS technology show that the proposed oscillation-based test strategy for OTA-C filters is suitable for catastrophic and parametric faults testing and also effective in detecting single and multiple faults with high fault coverage.Peer reviewedFinal Accepted Versio

High-frequency two-input CMOS OTA for continuous-time filter applications

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”A high-frequency fully differential CMOS operational transconductance amplifier (OTA) is presented for continuous-time filter applications in the megahertz range. The proposed design technique combines a linear cross-coupled quad input stage with an enhanced folded-cascode circuit to increase the output resistance of the amplifier. SPICE simulations show that DC-gain enhancement can be obtained without significant bandwidth limitation. The two-input OTA developed is used in high-frequency tuneable filter design based on IFLF and LC ladder simulation structures. Simulated results of parameters and characteristics of the OTA and filters in a standard 1.2 μm CMOS process (MOSIS) are presented. A tuning circuit is also discussed.Peer reviewe

A CMOS 100 MHz continuous-time seventh order 0.05° equiripple linear phase leapfrog multiple loop feedback Gm-C filter

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”A novel 100 MHz CMOS Gm-C seventh-order 0.05° equiripple linear phase low-pass multiple loop feedback (MLF) filter based on leapfrog (LF) topology is presented. The filter is implemented using a fully-differential linear, high performance operational transconductance amplifier (OTA) based on cross-coupled pairs. PSpice simulations in a standard TSMC 0.25 μm CMOS process and with a single 5 V power supply have shown that the cut-off frequency of the filter without and with gain boost ranges from 8-32 MHz and 15-100 MHz, respectively. With gain boost, total harmonic distortion (THD) for a differential input voltage Vid of 315 mVpp at 1 MHz is less than -40 dB, dynamic range at 1% THD is over 55 dB, output noise with bandwidth 500 MHz is only 300 μVRMS, and power consumption is 322 mW

A 0.18μm CMOS 9mW current-mode FLF linear phase filter with gain boost

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”The design and implementation of a CMOS continuous-time follow-the-leader-feedback (FLF) filter is described. The filter is implemented using a fully-differential linear, low voltage and low power consumption operational transconductance amplifier (OTA) based on a source degeneration topology. PSpice simulations using a standard TSMC 0.18 mum CMOS process with 2 V power supply have shown that the cut-off frequency of the filter ranges from 55 MHz to 160 MHz and dynamic range is about 45 dB. The group delay is less than 5% over the whole tuning range; the power consumption is only 9 mW

A 0.18μm CMOS 300MHz Current-Mode LF Seventh-order Linear Phase Filter for Hard Disk Read Channels

“This material is presented to ensure timely dissemination of scholarly and technical work. Copyright and all rights therein are retained by authors or by other copyright holders. All persons copying this information are expected to adhere to the terms and constraints invoked by each author's copyright. In most cases, these works may not be reposted without the explicit permission of the copyright holder." “Copyright IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.”A 300MHz CMOS seventh-order linear phase gm-C filter based on a current-mode multiple loop feedback (MLF) leap-frog (LF) structure is realized. The filter is implemented using a fully-differential linear operational transconductance amplifier (OTA) based on a source degeneration topology. PSpice simulations using a standard TSMC 0.18μm CMOS process with 2.5V power supply have shown that the cut-off frequency of the filter can be tuned from 260MHz to 320MHz and dynamic range is about 66dB. Group delay ripple is approximately 4.5% over the whole tuning range and maximum power consumption is 210mW

On the Design of Voltage-Controlled Sinusoidal Oscillators Using OTA's

A unified systematic approach to the design of voltage-controlled oscillators using only operational transconductance amplifiers (OTA's) and capacitors is discussed in this paper. Two classical oscillator models, i.e., quadrature and bandpass-based, are employed to generate several oscillator structures. They are very appropriate for silicon monolithic implementations. The resulting oscillation frequencies are proportional to the transconductance of the OTA and this makes the reported structures well-suited for building voltage controlled oscillators (VCO's). Amplitude stabilization circuits using both automatic gain control (AGC) mechanisms and limitation schemes are presented which are compatible with the transconductance amplifier capacitor oscillator (TACO). Experimental results from bipolar breadboard and CMOS IC prototypes are included showing good potential of OTA-based oscillators for high frequency VCO operation.Comisión Interministerial de Ciencia y Tecnología ME87-000

An Optoelectronic Stimulator for Retinal Prosthesis

Retinal prostheses require the presence of viable population of cells in the inner retina. Evaluations of retina with Age-Related Macular Degeneration (AMD) and Retinitis Pigmentosa (RP) have shown a large number of cells remain in the inner retina compared with the outer retina. Therefore, vision loss caused by AMD and RP is potentially treatable with retinal prostheses. Photostimulation based retinal prostheses have shown many advantages compared with retinal implants. In contrary to electrode based stimulation, light does not require mechanical contact. Therefore, the system can be completely external and not does have the power and degradation problems of implanted devices. In addition, the stimulating point is flexible and does not require a prior decision on the stimulation location. Furthermore, a beam of light can be projected on tissue with both temporal and spatial precision. This thesis aims at fi nding a feasible solution to such a system. Firstly, a prototype of an optoelectronic stimulator was proposed and implemented by using the Xilinx Virtex-4 FPGA evaluation board. The platform was used to demonstrate the possibility of photostimulation of the photosensitized neurons. Meanwhile, with the aim of developing a portable retinal prosthesis, a system on chip (SoC) architecture was proposed and a wide tuning range sinusoidal voltage-controlled oscillator (VCO) which is the pivotal component of the system was designed. The VCO is based on a new designed Complementary Metal Oxide Semiconductor (CMOS) Operational Transconductance Ampli er (OTA) which achieves a good linearity over a wide tuning range. Both the OTA and the VCO were fabricated in the AMS 0.35 µm CMOS process. Finally a 9X9 CMOS image sensor with spiking pixels was designed. Each pixel acts as an independent oscillator whose frequency is controlled by the incident light intensity. The sensor was fabricated in the AMS 0.35 µm CMOS Opto Process. Experimental validation and measured results are provided

Study of Adjustable Gains for Control of Oscillation Frequency and Oscillation Condition in 3R-2C Oscillator

An idea of adjustable gain in order to obtain controllable features is very useful for design of tuneable oscillators. Several active elements with adjustable properties (current and voltage gain) are discussed in this paper. Three modified oscillator conceptions that are quite simple, directly electronically adjustable, providing independent control of oscillation condition and frequency were designed. Positive and negative aspects of presented method of control are discussed. Expected assumptions of adjustability are verified experimentally on one of the presented solution

On the development of a MODEM for data transmission and control of electrical household appliances using the low-voltage power-line

This paper presents a CMOS 0,6μm mixed-signal MODEM ASIC for data transmission on the low-voltage power line. The circuit includes all the analog circuitry needed for input interfacing and modulation/demodulation (PLL-based frequency synthesis, slave filter banks with PLL master VCO for tuning, decision circuitry, etc.) plus the logic circuitry needed for control purposes. The circuit operates correctly in the whole industrial temperature range, from -45 to 80°C, under 5% variations of the 3.3V supply voltage.Comisión Interministerial de Ciencia y Tecnología FD97-1611(TIC)Ministerio de Ciencia y Tecnología TIC200 1-092

Very wide range tunable CMOS/bipolar current mirrors with voltage clamped input

In low power current mode signal processing circuits it is often necessary to use current mirrors to replicate and amplify/attenuate current signals and clamp the voltage of nodes with high parasitic capacitances so that the smallest currents do not introduce unacceptable delays. The use of tunable active-input current mirrors would meet both requirements. In conventional active-input current mirrors, stability compensation is required. Furthermore, once stabilized, the input current cannot be made arbitrarily small. In this paper we introduce two new active-input current mirrors that clamp their input node to a given voltage. One of them does not require compensation, while the other may under some circumstances. However, for both, the input current may take any value. The mirrors can operate with their transistors biased in strong inversion, weak inversion, or even as CMOS compatible lateral bipolar devices. If it is biased in weak inversion or as lateral bipolars, the current mirror gain can be tuned over a very wide range. According to the experimental measurements provided in this paper, the input current may spawn beyond nine decades and the current mirror gain can be tuned over 11 decades. As an application example, a sinusoidal gm-C-based VCO has been fabricated, whose oscillation frequency could be tuned for over seven decades, between 74 mHz and 1 MHz.Office of Naval Research (USA) N00014-95-1-040