Custom Integrated Circuits

Contains reports on ten research projects.Analog Devices, Inc.IBM CorporationNational Science Foundation/Defense Advanced Research Projects Agency Grant MIP 88-14612Analog Devices Career Development Assistant ProfessorshipU.S. Navy - Office of Naval Research Contract N0014-87-K-0825AT&TDigital Equipment CorporationNational Science Foundation Grant MIP 88-5876

Quiescent current testing of CMOS data converters

Power supply quiescent current (IDDQ) testing has been very effective in VLSI circuits designed in CMOS processes detecting physical defects such as open and shorts and bridging defects. However, in sub-micron VLSI circuits, IDDQ is masked by the increased subthreshold (leakage) current of MOSFETs affecting the efficiency of I¬DDQ testing. In this work, an attempt has been made to perform robust IDDQ testing in presence of increased leakage current by suitably modifying some of the test methods normally used in industry. Digital CMOS integrated circuits have been tested successfully using IDDQ and IDDQ methods for physical defects. However, testing of analog circuits is still a problem due to variation in design from one specific application to other. The increased leakage current further complicates not only the design but also testing. Mixed-signal integrated circuits such as the data converters are even more difficult to test because both analog and digital functions are built on the same substrate. We have re-examined both IDDQ and IDDQ methods of testing digital CMOS VLSI circuits and added features to minimize the influence of leakage current. We have designed built-in current sensors (BICS) for on-chip testing of analog and mixed-signal integrated circuits. We have also combined quiescent current testing with oscillation and transient current test techniques to map large number of manufacturing defects on a chip. In testing, we have used a simple method of injecting faults simulating manufacturing defects invented in our VLSI research group. We present design and testing of analog and mixed-signal integrated circuits with on-chip BICS such as an operational amplifier, 12-bit charge scaling architecture based digital-to-analog converter (DAC), 12-bit recycling architecture based analog-to-digital converter (ADC) and operational amplifier with floating gate inputs. The designed circuits are fabricated in 0.5 μm and 1.5 μm n-well CMOS processes and tested. Experimentally observed results of the fabricated devices are compared with simulations from SPICE using MOS level 3 and BSIM3.1 model parameters for 1.5 μm and 0.5 μm n-well CMOS technologies, respectively. We have also explored the possibility of using noise in VLSI circuits for testing defects and present the method we have developed

Custom Integrated Circuits

Contains reports on nine research projects.Analog Devices, Inc.International Business Machines CorporationJoint Services Electronics Program Contract DAAL03-89-C-0001U.S. Air Force - Office of Scientific Research Contract AFOSR 86-0164BDuPont CorporationNational Science Foundation Grant MIP 88-14612U.S. Navy - Office of Naval Research Contract N00014-87-K-0825American Telephone and TelegraphDigital Equipment CorporationNational Science Foundation Grant MIP 88-5876

Design of a Scan Chain for Side Channel Attacks on AES Cryptosystem for Improved Security

Scan chain-based attacks are side-channel attacks focusing on one of the most significant features of hardware test circuitry. A technique called Design for Testability (DfT) involves integrating certain testability components into a hardware design. However, this creates a side channel for cryptanalysis, providing crypto devices vulnerable to scan-based attacks. Advanced Encryption Standard (AES) has been proven as the most powerful and secure symmetric encryption algorithm announced by USA Government and it outperforms all other existing cryptographic algorithms. Furthermore, the on-chip implementation of private key algorithms like AES has faced scan-based side-channel attacks. With the aim of protecting the data for secure communication, a new hybrid pipelined AES algorithm with enhanced security features is implemented. This paper proposes testing an AES core with unpredictable response compaction and bit level-masking throughout the scan chain process. A bit-level scan flipflop focused on masking as a scan protection solution for secure testing. The experimental results show that the best security is provided by the randomized addition of masked scan flipflop through the scan chain and also provides minimal design difficulty and power expansion overhead with some negligible delay measures. Thus, the proposed technique outperforms the state-of-the-art LUT-based S-box and the composite sub-byte transformation model regarding throughput rate 2 times and 15 times respectively. And security measured in the avalanche effect for the sub-pipelined model has been increased up to 95 per cent with reduced computational complexity. Also, the proposed sub-pipelined S-box utilizing a composite field arithmetic scheme achieves 7 per cent area effectiveness and 2.5 times the hardware complexity compared to the LUT-based model

Oscillation-based DFT for Second-order Bandpass OTA-C Filters

This document is the Accepted Manuscript version. Under embargo until 6 September 2018. The final publication is available at Springer via https://doi.org/10.1007/s00034-017-0648-9.This paper describes a design for testability technique for second-order bandpass operational transconductance amplifier and capacitor filters using an oscillation-based test topology. The oscillation-based test structure is a vectorless output test strategy easily extendable to built-in self-test. The proposed methodology converts filter under test into a quadrature oscillator using very simple techniques and measures the output frequency. Using feedback loops with nonlinear block, the filter-to-oscillator conversion techniques easily convert the bandpass OTA-C filter into an oscillator. With a minimum number of extra components, the proposed scheme requires a negligible area overhead. The validity of the proposed method has been verified using comparison between faulty and fault-free simulation results of Tow-Thomas and KHN OTA-C filters. Simulation results in 0.25μm CMOS technology show that the proposed oscillation-based test strategy for OTA-C filters is suitable for catastrophic and parametric faults testing and also effective in detecting single and multiple faults with high fault coverage.Peer reviewedFinal Accepted Versio

Programmable CMOS Analog-to-Digital Converter Design and Testability

In this work, a programmable second order oversampling CMOS delta-sigma analog-to-digital converter (ADC) design in 0.5µm n-well CMOS processes is presented for integration in sensor nodes for wireless sensor networks. The digital cascaded integrator comb (CIC) decimation filter is designed to operate at three different oversampling ratios of 16, 32 and 64 to give three different resolutions of 9, 12 and 14 bits, respectively which impact the power consumption of the sensor nodes. Since the major part of power consumed in the CIC decimator is by the integrators, an alternate design is introduced by inserting coder circuits and reusing the same integrators for different resolutions and oversampling ratios to reduce power consumption. The measured peak signal-to-noise ratio (SNR) for the designed second order delta-sigma modulator is 75.6dB at an oversampling ratio of 64, 62.3dB at an oversampling ratio of 32 and 45.3dB at an oversampling ratio of 16. The implementation of a built-in current sensor (BICS) which takes into account the increased background current of defect-free circuits and the effects of process variation on ΔIDDQ testing of CMOS data converters is also presented. The BICS uses frequency as the output for fault detection in CUT. A fault is detected when the output frequency deviates more than ±10% from the reference frequency. The output frequencies of the BICS for various model parameters are simulated to check for the effect of process variation on the frequency deviation. A design for on-chip testability of CMOS ADC by linear ramp histogram technique using synchronous counter as register in code detection unit (CDU) is also presented. A brief overview of the histogram technique, the formulae used to calculate the ADC parameters, the design implemented in 0.5µm n-well CMOS process, the results and effectiveness of the design are described. Registers in this design are replaced by 6T-SRAM cells and a hardware optimized on-chip testability of CMOS ADC by linear ramp histogram technique using 6T-SRAM as register in CDU is presented. The on-chip linear ramp histogram technique can be seamlessly combined with ΔIDDQ technique for improved testability, increased fault coverage and reliable operation

Secure Split Test for Preventing IC Piracy by Un-Trusted Foundry and Assembly

In the era of globalization, integrated circuit design and manufacturing is spread across different continents. This has posed several hardware intrinsic security issues. The issues are related to overproduction of chips without knowledge of designer or OEM, insertion of hardware Trojans at design and fabrication phase, faulty chips getting into markets from test centers, etc. In this thesis work, we have addressed the problem of counterfeit IC‟s getting into the market through test centers. The problem of counterfeit IC has different dimensions. Each problem related to counterfeiting has different solutions. Overbuilding of chips at overseas foundry can be addressed using passive or active metering. The solution to avoid faulty chips getting into open markets from overseas test centers is secure split test (SST). The further improvement to SST is also proposed by other researchers and is known as Connecticut Secure Split Test (CSST). In this work, we focus on improvements to CSST techniques in terms of security, test time and area. In this direction, we have designed all the required sub-blocks required for CSST architecture, namely, RSA, TRNG, Scrambler block, study of benchmark circuits like S38417, adding scan chains to benchmarks is done. Further, as a security measure, we add, XOR gate at the output of the scan chains to obfuscate the signal coming out of the scan chains. Further, we have improved the security of the design by using the PUF circuit instead of TRNG and avoid the use of the memory circuits. This use of PUF not only eliminates the use of memory circuits, but also it provides the way for functional testing also. We have carried out the hamming distance analysis for introduced security measure and results show that security design is reasonably good.Further, as a future work we can focus on: • Developing the circuit which is secuered for the whole semiconductor supply chain with reasonable hamming distance and less area overhead

Testing a CMOS operational amplifier circuit using a combination of oscillation and IDDQ test methods

This work presents a case study, which attempts to improve the fault diagnosis and testability of the oscillation testing methodology applied to a typical two-stage CMOS operational amplifier. The proposed test method takes the advantage of good fault coverage through the use of a simple oscillation based test technique, which needs no test signal generation and combines it with quiescent supply current (IDDQ) testing to provide a fault confirmation. A built in current sensor (BICS), which introduces insignificant performance degradation of the circuit-under-test (CUT), has been utilized to monitor the power supply quiescent current changes in the CUT. The testability has also been enhanced in the testing procedure using a simple fault-injection technique. The approach is attractive for its simplicity, robustness and capability of built-in-self test (BIST) implementation. It can also be generalized to the oscillation based test structures of other CMOS analog and mixed-signal integrated circuits. The practical results and simulations confirm the functionality of the proposed test method

From Microelectronics to Nanoelectronics: Introducing Nanotechnology to VLSI Curricula

© 2011 by ASEEIn the past decades, VLSI industries constantly shrank the size of transistors, so that more and more transistors can be built into the same chip area to make VLSI more and more powerful in its functions. As the typical feature size of CMOS VLSI is shrunk into deep submicron domain, nanotechnology is the next step in order to maintain Moore’s law for several more decades. Nanotechnology not only further improves the resolution in traditional photolithography process, but also introduces many brand-new fabrication strategies, such as bottom-up molecular self-assembly. Nanotechnology is also enabling many novel devices and circuit architectures which are totally different from current microelectronics circuits, such as quantum computing, nanowire crossbar circuits, spin electronics, etc. Nanotechnology is bringing another technology revolution to traditional CMOS VLSI technology. In order to train students to meet the quickly-increasing industry demand for nextgeneration nanoelectronics engineers, we are making efforts to introduce nanotechnology into our VLSI curricula. We have developed a series of VLSI curricula which include CPE/EE 448D - Introduction to VLSI, EE 548 - Low Power VLSI Circuit Design, EE 458 - Analog VLSI Circuit Design, EE 549 - VLSI Testing, etc. Furthermore, we developed a series of micro and nanotechnology related courses, such as EE 451 - Nanotechnology, EE 448 - Microelectronic Fabrication, EE 446 – MEMS (Microelectromechanical Systems). We introduce nanotechnology into our VLSI curricula, and teach the students about various devices, fabrication processes, circuit architectures, design and simulation skills for future nanotechnology-based nanoelectronic circuits. Some examples are nanowire crossbar circuit architecture, carbon-nanotube based nanotransistor, single-electron transistor, spintronics, quantum computing, bioelectronic circuits, etc. Students show intense interest in these exciting topics. Some students also choose nanoelectronics as the topic for their master project/thesis, and perform successful research in the field. The program has attracted many graduate students into the field of nanoelectronics