System-on-package MHMIC milimeter-wave frequency synthesizer for 60GHz WPANs

We present a low-cost millimeter-wave frequency synthesizer with ultralow phase noise, implemented using system-on-package (SoP) techniques for high-data-rate wireless personal area network (WPAN) systems operating in the unlicensed 60 GHz ISM band (57–64 GHz). The phase noise specification of the proposed frequency synthesizer is derived for a worst case scenario of an 802.11.3c system, which uses a 64-QAM 512-carrier-OFDM modulation, and a data rate of 5.775 Gbps. Our design approach adopts commercial-of-the-shelf (COTS) components integrated in a low-cost alumina-based miniature hybrid microwave integrated circuit (MHMIC) package. The proposed design approach reduces not only the system cost and time-to-market, but also enhances the system performance in comparison with system-on-chip (SoC) designs. The synthesizer has measured phase noise of −111.5 dBc/Hz at 1 MHz offset and integrated phase noise of 2.8° (simulated: 2.5°) measured at 57.6 GHz with output power of +1 dBm

Theory Based on Device Current Clipping to Explain and Predict Performance Including Distortion of Power Amplifiers for Wireless Communication Systems

Power amplifiers are critical components in wireless communication systems that need to have high efficiency, in order to conserve battery life and minimise heat generation, and at the same time low distortion, in order to prevent increase of bit error rate due to constellation errors and adjacent channel interference. This thesis is aimed at meeting a need for greater understanding of distortion generated by power amplifiers of any technology, in order to help designers manage better the trade-off between obtaining high efficiency and low distortion. The theory proposed in this thesis to explain and predict the performance of power amplifiers, including distortion, is based on analysis of clipping of the power amplifier device current, and it is a major extension of previous clipping analyses, that introduces many key definitions and concepts. Distortion and other power amplifier metrics are determined in the form of 3-D surfaces that are plotted against PA class, which is determined by bias voltage, and input signal power level. It is shown that the surface of distortion exhibits very high levels due to clipping in the region where efficiency is high. This area of high distortion is intersected by a valley that is ‘L’-shaped. The 'L'-shaped valley is subject to a rotation that depends on the softness of the cut-off of the power amplifier device transfer characteristic. The distortion surface with rotated 'L'-shaped valley leads to predicted curves for distortion versus input signal power that match published measured curves for power amplifiers even using very simple device models. The distortion versus input signal power curves have types that are independent of technology. In class C, there is a single deep null. In the class AB range, that is divided into three sub-ranges, there may be two deep nulls (sub-range AB(B)), a ledge (sub-range AB(A)) or a shallow null with varying depth (sub-range AB(AB))

Integrated RF oscillators and LO signal generation circuits

This thesis deals with fully integrated LC oscillators and local oscillator (LO) signal generation circuits. In communication systems a good-quality LO signal for up- and down-conversion in transmitters is needed. The LO signal needs to span the required frequency range and have good frequency stability and low phase noise. Furthermore, most modern systems require accurate quadrature (IQ) LO signals. This thesis tackles these challenges by presenting a detailed study of LC oscillators, monolithic elements for good-quality LC resonators, and circuits for IQ-signal generation and for frequency conversion, as well as many experimental circuits. Monolithic coils and variable capacitors are essential, and this thesis deals with good structures of these devices and their proper modeling. As experimental test devices, over forty monolithic inductors and thirty varactors have been implemented, measured and modeled. Actively synthesized reactive elements were studied as replacements for these passive devices. At first glance these circuits show promising characteristics, but closer noise and nonlinearity analysis reveals that these circuits suffer from high noise levels and a small dynamic range. Nine circuit implementations with various actively synthesized variable capacitors were done. Quadrature signal generation can be performed with three different methods, and these are analyzed in the thesis. Frequency conversion circuits are used for alleviating coupling problems or to expand the number of frequency bands covered. The thesis includes an analysis of single-sideband mixing, frequency dividers, and frequency multipliers, which are used to perform the four basic arithmetical operations for the frequency tone. Two design cases are presented. The first one is a single-sideband mixing method for the generation of WiMedia UWB LO-signals, and the second one is a frequency conversion unit for a digital period synthesizer. The last part of the thesis presents five research projects. In the first one a temperature-compensated GaAs MESFET VCO was developed. The second one deals with circuit and device development for an experimental-level BiCMOS process. A cable-modem RF tuner IC using a SiGe process was developed in the third project, and a CMOS flip-chip VCO module in the fourth one. Finally, two frequency synthesizers for UWB radios are presented