Cost-Effective TSV Grouping for Yield Improvement of 3D-ICs

Three-dimensional Integrated Circuits (3D-ICs) vertically stack multiple silicon dies to reduce overall wire length, power consumption, and allow integration of heterogeneous technologies. Through-silicon-vias (TSVs) which act as vertical links between layers pose challenges for 3D integration design. TSV defects can happen in fabrication process and bonding stage, which can reduce the yield and increase the cost. Recent work proposed the employment of redundant TSVs to improve the yield of 3D-ICs. This paper presents a redundant TSVs grouping technique, which partition regular and redundant TSVs into groups. For each group, a set of multiplexers are used to select good signal paths away from defective TSVs. We investigate the impact of grouping ratio (regular-to-redundant TSVs in one group) on trade-off between yield and hardware overhead. We also show probabilistic models for yield analysis under the influence of independent and clustering defect distributions. Simulation results show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratios lead to achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios

A Cost-Effective Fault Tolerance Technique for Functional TSV in 3-D ICs

Regular and redundant through-silicon via (TSV) interconnects are used in fault tolerance techniques of 3-D IC. However, the fabrication process of TSVs results in defects that reduce the yield and reliability of TSVs. On the other hand, each TSV is associated with a significant amount of on-chip area overhead. Therefore, unlike the state-of-the-art fault tolerance architectures, here we propose the time division multiplexing access (TDMA)-based fault tolerance technique without using any redundant TSVs, which reduces the area overhead and enhances the yield. In the proposed technique, by means of TDMA, we reroute the signal through defect-free TSV. Subsequently, an architecture based on the proposed technique has been designed, evaluated, and validated on logic-on-logic 3-D IWLS'05 benchmark circuits using 130-nm technology node. The proposed technique is found to reduce the area overhead by 28.70%-40.60%, compared to the state-of-the-art architectures and results in a yield of 98.9%-99.8%

Characterization and Implementation of Fault-Tolerant Vertical Links for 3-D Networks-on-Chip

Through silicon vias (TSVs) provide an efficient way to support vertical communication among different layers of a vertically stacked chip, enabling scalable 3-D networks-on-chip (NoC) architectures. Unfortunately, low TSV yields significantly impact the feasibility of high-bandwidth vertical connectivity. In this paper, we present a semi-automated design flow for 3-D NoCs including a defect-tolerance scheme to increase the global yield of 3-D stacked chips. Starting from an accurate physical and geometrical model of TSVs: 1) we extract a circuit-level model for vertical interconnections; 2) we use it to evaluate the design implications of extending switch architectures with ports in the vertical direction; moreover, 3) we present a defect-tolerance technique for TSV-based multi-bit links through an effective use of redundancy; and finally, 4) we present a design flow allowing for post-layout simulation of NoCs with links in all three physical dimensions. Experimental results show that a 3-D NoC implementation yields around 10% frequency improvement over a 2-D one, thanks to the propagation delay advantage of TSVs and the shorter links. In addition, the adopted fault tolerance scheme demonstrates a significant yield improvement, ranging from 66% to 98%, with a low area cost (20.9% on a vertical link in a NoC switch, which leads a modest 2.1% increase in the total switch area) in 130 nm technology, with minimal impact on very large-scale integrated design and test flows

Investigation into yield and reliability enhancement of TSV-based three-dimensional integration circuits

Three dimensional integrated circuits (3D ICs) have been acknowledged as a promising technology to overcome the interconnect delay bottleneck brought by continuous CMOS scaling. Recent research shows that through-silicon-vias (TSVs), which act as vertical links between layers, pose yield and reliability challenges for 3D design. This thesis presents three original contributions.The first contribution presents a grouping-based technique to improve the yield of 3D ICs under manufacturing TSV defects, where regular and redundant TSVs are partitioned into groups. In each group, signals can select good TSVs using rerouting multiplexers avoiding defective TSVs. Grouping ratio (regular to redundant TSVs in one group) has an impact on yield and hardware overhead. Mathematical probabilistic models are presented for yield analysis under the influence of independent and clustering defect distributions. Simulation results using MATLAB show that for a given number of TSVs and TSV failure rate, careful selection of grouping ratio results in achieving 100% yield at minimal hardware cost (number of multiplexers and redundant TSVs) in comparison to a design that does not exploit TSV grouping ratios. The second contribution presents an efficient online fault tolerance technique based on redundant TSVs, to detect TSV manufacturing defects and address thermal-induced reliability issue. The proposed technique accounts for both fault detection and recovery in the presence of three TSV defects: voids, delamination between TSV and landing pad, and TSV short-to-substrate. Simulations using HSPICE and ModelSim are carried out to validate fault detection and recovery. Results show that regular and redundant TSVs can be divided into groups to minimise area overhead without affecting the fault tolerance capability of the technique. Synthesis results using 130-nm design library show that 100% repair capability can be achieved with low area overhead (4% for the best case). The last contribution proposes a technique with joint consideration of temperature mitigation and fault tolerance without introducing additional redundant TSVs. This is achieved by reusing spare TSVs that are frequently deployed for improving yield and reliability in 3D ICs. The proposed technique consists of two steps: TSV determination step, which is for achieving optimal partition between regular and spare TSVs into groups; The second step is TSV placement, where temperature mitigation is targeted while optimizing total wirelength and routing difference. Simulation results show that using the proposed technique, 100% repair capability is achieved across all (five) benchmarks with an average temperature reduction of 75.2? (34.1%) (best case is 99.8? (58.5%)), while increasing wirelength by a small amount