Design and control of laser micromachining workstation

The production process of miniature devices and microsystems requires the utilization of non-conventional micromachining techniques. In the past few decades laser micromachining has became micro-manufacturing technique of choice for many industrial and research applications. This paper discusses the design of motion control system for a laser micromachining workstation with particulars about automatic focusing and control of work platform used in the workstation. The automatic focusing is solved in a sliding mode optimization framework and preview controller is used to control the motion platform. Experimental results of both motion control and actual laser micromachining are presented

Lithium niobate micromachining for the fabrication of microfluidic droplet generators

In this paper, we present the first microfluidic junctions for droplet generation directly engraved on lithium niobate crystals by micromachining techniques, preparatory to a fully integrated opto-microfluidics lab-on-chip system. In particular, laser ablation technique and the mechanical micromachining technique are exploited to realise microfluidic channels in T-and cross junction configurations. The quality of both lateral and bottom surfaces of the channels are therefore compared together with a detailed study of their roughness measured by means of atomic force microscopy in order to evaluate the final performance achievable in an optofluidic device. Finally, the microfluidics performances of these water-in-oil droplets generators are investigated depending on these micromachining techniques, with particular focus on a wide range of droplet generation rates

Thermal design issues and performance of microcalorimeter arrays at sub-Kelvin temperatures

We have produced 5/spl times/5 pixel arrays of microcalorimeters using bulk micromachining. Analysis of our data provides the thermal conductivity parameters of Si/sub x/N/sub y/ 1 /spl mu/m thick membranes at 100 mK. Moreover we find that the thermal transport at 100 mK in Si beams, with dimensions 1.25 mm /spl times/ 0.35mm /spl times/ 35/spl mu/m (length /spl times/ height /spl times/ width) is dominated by ballistic phonons with a mean free path of 110 /spl mu/m. These thermal parameters can be used for modelling future 32 /spl times/ 32 pixel arrays. In addition we operated three pixels in a 5 /spl times/ 5 array of microcalorimeters and find that the pixel to pixel reproducibility is very good. When used as an X-ray microcalorimeter individual pixels have a thermal decay time of 200 /spl mu/s is and their energy resolution is between 6 and 7 eV for 5.89 keV X-ray photons

Design, fabrication and characterization of monolithic embedded parylene microchannels in silicon substrate

This paper presents a novel channel fabrication technology of bulk-micromachined monolithic embedded polymer channels in silicon substrate. The fabrication process favorably obviates the need for sacrifical materials in surface-micromachined channels and wafer-bonding in conventional bulk-micromachined channels. Single-layer-deposited parylene C (poly-para-xylylene C) is selected as a structural material in the microfabricated channels/columns to conduct life science research. High pressure capacity can be obtained in these channels by the assistance of silicon substrate support to meet the needs of high-pressure loading conditions in microfluidic applications. The fabrication technology is completely compatible with further lithographic CMOS/MEMS processes, which enables the fabricated embedded structures to be totally integrated with on-chip micro/nano-sensors/actuators/structures for miniaturized lab-on-a-chip systems. An exemplary process was described to show the feasibility of combining bulk micromachining and surface micromachining techniques in process integration. Embedded channels in versatile cross-section profile designs have been fabricated and characterized to demonstrate their capabilities for various applications. A quasi-hemi-circular-shaped embedded parylene channel has been fabricated and verified to withstand inner pressure loadings higher than 1000 psi without failure for micro-high performance liquid chromatography (µHPLC) analysis. Fabrication of a high-aspect-ratio (internal channel height/internal channel width, greater than 20) quasi-rectangular-shaped embedded parylene channel has also been presented and characterized. Its implementation in a single-mask spiral parylene column longer than 1.1 m in a 3.3 mm × 3.3 mm square size on a chip has been demonstrated for prospective micro-gas chromatography (µGC) and high-density, high-efficiency separations. This proposed monolithic embedded channel technology can be extensively implemented to fabricate microchannels/columns in high-pressure microfludics and high-performance/high-throughput chip-based micro total analysis systems (µTAS)

Design of a pulse power supply unit for micro-ECM

Electrochemical micro-machining (μECM) requires a particular pulse power supply unit (PSU) to be developed in order to achieve desired machining performance. This paper summarises the development of a pulse PSU meeting the requirements of μECM. The pulse power supply provides tens of nanosecond pulse duration, positive and negative bias voltages and a polarity switching functionality. It fulfils the needs for tool preparation with reversed pulsed ECM on the machine. Moreover, the PSU is equipped with an ultrafast overcurrent protection which prevents the tool electrode from being damaged in case of short circuits. The developed pulse PSU was used to fabricate micro-tools out of 170 μm WC-Co alloy shafts via micro-electrochemical turning and drill deep holes via μECM in a disk made of 18NiCr6. The electrolyte used for both processes was a mixture of sulphuric acid and NaNO3 aqueous solutions.The research reported in this paper is supported by the European Commission within the project “Minimizing Defects in Micro-Manufacturing Applications (MIDEMMA)” (FP7-2011-NMP-ICT-FoF-285614

Surface micromachined mechanisms and micromotors

Electric micromotors are sub-millimeter sized actuators capable of unrestrained motion in at least one degree of freedom. Polysilicon surface micromachining using heavily phosphorus-doped LPCVD polysilicon for the structural material, LPCVD silicon nitride for the electrical isolation and deposited silicon dioxide for the sacrificial material has formed the fabrication technology base for the development of these micromotors. Two polysilicon surface micromachining processes, referred to here as the center-pin and flange, have been demonstrated for the fabrication of passive mechanisms and micromotors. Passive mechanisms such as gear trains, cranks and manipulators have been implemented on silicon. Reported operational micromotors have been of the rotary variable-capacitance salient-pole and harmonic (or wobble) side-drive designs. These micromotors are capable of motive torques in the 10 pN m order of magnitude range. Preliminary progress has been made in studying the operational, friction and wear characteristics of these micromechanical devices. Typical operational voltages have been as low as 37 V and 26 V across 1.5 mu m air gap salient-pole and harmonic micromotors. These excitations correspond to electric field intensities above 10(8) Vm-1 in the micromotor air gaps. Salient-pole and wobble micromotors have been reported to operate at speeds as high as 15000 rpm and 700 rpm, respectively. Micromotor lifetimes of at least many millions of cycles over a period of several days have been reported

Micromachining of buried micro channels in silicon

A new method for the fabrication of micro structures for fluidic applications, such as channels, cavities, and connector holes in the bulk of silicon wafers, called buried channel technology (BCT), is presented in this paper. The micro structures are constructed by trench etching, coating of the sidewalls of the trench, removal of the coating at the bottom of the trench, and etching into the bulk of the silicon substrate. The structures can be sealed by deposition of a suitable layer that closes the trench. BCT is a process that can be used to fabricate complete micro channels in a single wafer with only one lithographic mask and processing on one side of the wafer, without the need for assembly and bonding. The process leaves a substrate surface with little topography, which easily allows further processing, such as the integration of electronic circuits or solid-state sensors. The essential features of the technology, as well as design rules and feasible process schemes, will be demonstrated on examples from the field of ¿-fluidic

Micro systems technology

The emerging field of Micro Systems Technology is described. Micro Systems Technology can be seen as the meeting of disciplines, a product of convergence along different lines. Apart from the traditional and ever developing line of 'classical' precision engineering, there is a line along micro electronics, micro sensors and actuators. This is the line we focus on in this contribution. The third line worth mentioning is the one along the upcoming field of molecular engineering. The main purpose of this paper is to show the wealth of possibilities and consequently the need for 'integral design' management

Design of an electrochemical micromachining machine

Electrochemical micromachining (μECM) is a non-conventional machining process based on the phenomenon of electrolysis. μECM became an attractive area of research due to the fact that this process does not create any defective layer after machining and that there is a growing demand for better surface integrity on different micro applications including microfluidics systems, stress-free drilled holes in automotive and aerospace manufacturing with complex shapes, etc. This work presents the design of a next generation μECM machine for the automotive, aerospace, medical and metrology sectors. It has three axes of motion (X, Y, Z) and a spindle allowing the tool-electrode to rotate during machining. The linear slides for each axis use air bearings with linear DC brushless motors and 2-nm resolution encoders for ultra precise motion. The control system is based on the Power PMAC motion controller from Delta Tau. The electrolyte tank is located at the rear of the machine and allows the electrolyte to be changed quickly. This machine features two process control algorithms: fuzzy logic control and adaptive feed rate. A self-developed pulse generator has been mounted and interfaced with the machine and a wire ECM grinding device has been added. The pulse generator has the possibility to reverse the pulse polarity for on-line tool fabrication.The research reported in this paper is supported by the European Commission within the project “Minimizing Defects in Micro-Manufacturing Applications (MIDEMMA)” (FP7-2011-NMPICT- FoF-285614)

Fabrication of three-dimensional microdisk resonators in calcium fluoride by femtosecond laser micromachining

We report on fabrication of on-chip calcium fluoride (CaF2) microdisk resonators using water-assisted femtosecond laser micromachining. Focused ion beam (FIB) milling is used to create ultra-smooth sidewalls. The quality (Q)-factors of the fabricated microresonators are measured to be 4.2x10^4 at wavelengths near 1550 nm. The Q factor is mainly limited by the scattering from the bottom surface of the disk whose roughness remains high due to the femtosecond laser micromachining process. This technique facilitates formation of on-chip microresonators on various kinds of bulk crystalline materials, which can benefit a wide range of applications such as nonlinear optics, quantum optics, and chip-level integration of photonic devices.Comment: 7 pages, 3 figure