Characterization of Asphalt Treated Base Course Material

INE/AUTC 11.0

Morphological characterization of shocked porous material

Morphological measures are introduced to probe the complex procedure of shock wave reaction on porous material. They characterize the geometry and topology of the pixelized map of a state variable like the temperature. Relevance of them to thermodynamical properties of material is revealed and various experimental conditions are simulated. Numerical results indicate that, the shock wave reaction results in a complicated sequence of compressions and rarefactions in porous material. The increasing rate of the total fractional white area $A$ roughly gives the velocity $D$ of a compressive-wave-series. When a velocity $D$ is mentioned, the corresponding threshold contour-level of the state variable, like the temperature, should also be stated. When the threshold contour-level increases, $D$ becomes smaller. The area $A$ increases parabolically with time $t$ during the initial period. The $A(t)$ curve goes back to be linear in the following three cases: (i) when the porosity $\delta$ approaches 1, (ii) when the initial shock becomes stronger, (iii) when the contour-level approaches the minimum value of the state variable. The area with high-temperature may continue to increase even after the early compressive-waves have arrived at the downstream free surface and some rarefactive-waves have come back into the target body. In the case of energetic material ... (see the full text)Comment: 3 figures in JPG forma

Characterization of a new photorefractive material: Kl-yLyT1-xNx

We report the growth and characterization of a new photorefractive material, potassium lithium tantalate niobate (KLTN). A KLTN crystal doped with copper is demonstrated to yield high diffraction efficiency of photorefractive gratings in the paraelectric phase. Voltage-controllable index gratings with n, = 8.5 x 10^-5 were achieved, which yielded diffraction efficiencies of 75% in a 2.9-mm-thick sample. In addition, diffraction was observed in the paraelectric phase without an applied field. This effect is attributed to a growth-induced strain field

Characterization of the material response in the granular ratcheting

The existence of a very special ratcheting regime has recently been reported in a granular packing subjected to cyclic loading \cite{alonso04}. In this state, the system accumulates a small permanent deformation after each cycle. After a short transient regime, the value of this permanent strain accumulation becomes independent on the number of cycles. We show that a characterization of the material response in this peculiar state is possible in terms of three simple macroscopic variables. They are defined that, they can be easily measured both in the experiments and in the simulations. We have carried out a thorough investigation of the micro- and macro-mechanical factors affecting these variables, by means of Molecular Dynamics simulations of a polydisperse disk packing, as a simple model system for granular material. Biaxial test boundary conditions with a periodically cycling load were implemented. The effect on the plastic response of the confining pressure, the deviatoric stress and the number of cycles has been investigated. The stiffness of the contacts and friction has been shown to play an important role in the overall response of the system. Specially elucidating is the influence of the particular hysteretical behavior in the stress-strain space on the accumulation of permanent strain and the energy dissipation.Comment: 13 pages, 20 figures. Submitted to PR

Characterization methods dedicated to nanometer-thick hBN layers

Hexagonal boron nitride (hBN) regains interest as a strategic component in graphene engineering and in van der Waals heterostructures built with two dimensional materials. It is crucial then, to handle reliable characterization techniques capable to assess the quality of structural and electronic properties of the hBN material used. We present here characterization procedures based on optical spectroscopies, namely cathodoluminescence and Raman, with the additional support of structural analysis conducted by transmission electron microscopy. We show the capability of optical spectroscopies to investigate and benchmark the optical and structural properties of various hBN thin layers sources

Cracking in asphalt materials

This chapter provides a comprehensive review of both laboratory characterization and modelling of bulk material fracture in asphalt mixtures. For the purpose of organization, this chapter is divided into a section on laboratory tests and a section on models. The laboratory characterization section is further subdivided on the basis of predominant loading conditions (monotonic vs. cyclic). The section on constitutive models is subdivided into two sections, the first one containing fracture mechanics based models for crack initiation and propagation that do not include material degradation due to cyclic loading conditions. The second section discusses phenomenological models that have been developed for crack growth through the use of dissipated energy and damage accumulation concepts. These latter models have the capability to simulate degradation of material capacity upon exceeding a threshold number of loading cycles.Peer ReviewedPostprint (author's final draft

Material characterization at high strain by adapted tensile tests

The strength of materials at high strain levels has\ud been determined using the so-called Continuous-Bendingunder-\ud Tension (CBT) test. This is a modified tensile test\ud where the specimen is subjected to repetitive bending at the\ud same time. This test enables to create high levels of uniform\ud strain. A wide variety of materials has been tested this way.\ud The strength of the material after CBT testing has been\ud measured in different ways: by secondary tensile tests, by\ud interrupted CBT tests, and directly from the fracture in the\ud CBT test. All methods yield similar results: the strength is\ud largely unaffected by the cyclic pre-deformation and mainly\ud depends on the overall increase in length. Only for multiphase\ud materials the strength shows a minor influence of\ud CBT test conditions. The hardening follows the extrapolated\ud hardening observed in a conventional tensile test, except for\ud brass. This test method can potentially be used for measuring\ud hardening curves at high strain levels

Statistical distribution of mechanical properties for three graphite-epoxy material systems

Graphite-epoxy composites are playing an increasing role as viable alternative materials in structural applications necessitating thorough investigation into the predictability and reproducibility of their material strength properties. This investigation was concerned with tension, compression, and short beam shear coupon testing of large samples from three different material suppliers to determine their statistical strength behavior. Statistical results indicate that a two Parameter Weibull distribution model provides better overall characterization of material behavior for the graphite-epoxy systems tested than does the standard Normal distribution model that is employed for most design work. While either a Weibull or Normal distribution model provides adequate predictions for average strength values, the Weibull model provides better characterization in the lower tail region where the predictions are of maximum design interest. The two sets of the same material were found to have essentially the same material properties, and indicate that repeatability can be achieved