Advances in Architectures and Tools for FPGAs and their Impact on the Design of Complex Systems for Particle Physics

The continual improvement of semiconductor technology has provided rapid advancements in device frequency and density. Designers of electronics systems for high-energy physics (HEP) have benefited from these advancements, transitioning many designs from fixed-function ASICs to more flexible FPGA-based platforms. Today’s FPGA devices provide a significantly higher amount of resources than those available during the initial Large Hadron Collider design phase. To take advantage of the capabilities of future FPGAs in the next generation of HEP experiments, designers must not only anticipate further improvements in FPGA hardware, but must also adopt design tools and methodologies that can scale along with that hardware. In this paper, we outline the major trends in FPGA hardware, describe the design challenges these trends will present to developers of HEP electronics, and discuss a range of techniques that can be adopted to overcome these challenges

FPGA ARCHITECTURE AND VERIFICATION OF BUILT IN SELF-TEST (BIST) FOR 32-BIT ADDER/SUBTRACTER USING DE0-NANO FPGA AND ANALOG DISCOVERY 2 HARDWARE

The integrated circuit (IC) is an integral part of everyday modern technology, and its application is very attractive to hardware and software design engineers because of its versatility, integration, power consumption, cost, and board area reduction. IC is available in various types such as Field Programming Gate Array (FPGA), Application Specific Integrated Circuit (ASIC), System on Chip (SoC) architecture, Digital Signal Processing (DSP), microcontrollers (μC), and many more. With technology demand focused on faster, low power consumption, efficient IC application, design engineers are facing tremendous challenges in developing and testing integrated circuits that guaranty functionality, high fault coverage, and reliability as the transistor technology is shrinking to the point where manufacturing defects of ICs are affecting yield which associates with the increased cost of the part. The competitive IC market is pressuring manufactures of ICs to develop and market IC in a relatively quick turnaround which in return requires design and verification engineers to develop an integrated self-test structure that would ensure fault-free and the quality product is delivered on the market. 70-80% of IC design is spent on verification and testing to ensure high quality and reliability for the enduser. To test complex and sophisticated IC designs, the verification engineers must produce laborious and costly test fixtures which affect the cost of the part on the competitive market. To avoid increasing the part cost due to yield and test time to the end-user and to keep up with the competitive market many IC design engineers are deviating from complex external test fixture approach and are focusing on integrating Built-in Self-Test (BIST) or Design for Test (DFT) techniques onto IC’s which would reduce time to market but still guarantee high coverage for the product. Understanding the BIST, the architecture, as well as the application of IC, must be understood before developing IC. The architecture of FPGA is elaborated in this paper followed by several BIST techniques and applications of those BIST relative to FPGA, SoC, analog to digital (ADC), or digital to analog converters (DAC) that are integrated on IC. Paper is concluded with verification of BIST for the 32-bit adder/subtracter designed in Quartus II software using the Analog Discovery 2 module as stimulus and DE0-NANO FPGA board for verification

High-level verification flow for a high-level synthesis-based digital logic design

Abstract. High-level synthesis (HLS) is a method for generating register-transfer level (RTL) hardware description of digital logic designs from high-level languages, such as C/C++/SystemC or MATLAB. The performance and productivity benefits of HLS stem from the untimed, high abstraction level input languages. Another advantage is that the design and verification can focus on the features and high-level architecture, instead of the low-level implementation details. The goal of this thesis was to define and implement a high-level verification (HLV) flow for an HLS design written in C++. The HLV flow takes advantage of the performance and productivity of C++ as opposed to hardware description languages (HDL) and minimises the required RTL verification work. The HLV flow was implemented in the case study of the thesis. The HLS design was verified in a C++ verification environment, and Catapult Coverage was used for pre-HLS coverage closure. Post-HLS verification and coverage closure were done in Universal Verification Methodology (UVM) environment. C++ tests used in the pre-HLS coverage closure were reimplemented in UVM, to get a high initial RTL coverage without manual RTL code analysis. The pre-HLS C++ design was implemented as a predictor into the UVM testbench to verify the equivalence of C++ versus RTL and to speed up post-HLS coverage closure. Results of the case study show that the HLV flow is feasible to implement in practice. The flow shows significant performance and productivity gains of verification in the C++ domain when compared to UVM. The UVM implementation of a somewhat incomplete set of pre-HLS tests and formal exclusions resulted in an initial post-HLS coverage of 96.90%. The C++ predictor implementation was a valuable tool in post-HLS coverage closure. A total of four weeks of coverage work in pre- and post-HLS phases was required to reach 99% RTL coverage. The total time does not include the time required to build both C++ and UVM verification environments.Korkean tason verifiointivuo korkean tason synteesiin perustuvalle digitaalilogiikkasuunnitelmalle. Tiivistelmä. Korkean tason synteesi (HLS) on menetelmä, jolla generoidaan rekisterisiirtotason (RTL) laitteistokuvausta digitaalisille logiikkasuunnitelmille käyttäen korkean tason ohjelmointikieliä, kuten C-pohjaisia kieliä tai MATLAB:ia. HLS:n suorituskykyyn ja tuottavuuteen liittyvät hyödyt perustuvat ohjelmointikielien tarjoamaan korkeampaan abstraktiotasoon. HLS:ää käyttäen suunnittelu- ja varmennustyö voi keskittyä ominaisuuksiin ja korkean tason arkkitehtuuriin matalan tason yksityiskohtien sijaan. Tämän diplomityön tavoite oli määritellä ja implementoida korkean tason verifiointivuo (HLV-vuo) C++:lla kirjoitetulle HLS-suunnitelmalle. HLV-vuo hyödyntää ohjelmointikielien tarjoamaa suorituskykyä ja korkeampaa abstraktion tasoa kovonkuvauskielien sijaan ja siten minimoi RTL:n varmennukseen vaadittavaa työtä. HLV vuo implementoitiin tapaustutkimuksessa. HLS-suunnitelma varmennettiin C++ -verifiointiympäristössä, ja Catapult Coveragea käytettiin kattavuuden analysointiin. RTL-kattavuutta mitattiin universaalilla verifiointimetodologialla (UVM) tehdyssä ympäristössä. C++ varmennuksessa käytetyt testivektorit implementoitiin uudelleen UVM-ympäristössä, jotta RTL-kattavuuden lähtötaso olisi korkea ilman manuaalista RTL-analyysiä. C++-suunnitelma implementoitiin prediktorina (referenssimallina) UVM-testipenkkiin koodikattavuuden parantamiseksi. Tapaustutkimuksen tulokset osoittavat, että määritelty HLV-vuo on toteutettavissa käytännössä. Vuota käyttämällä saavutetaan merkittäviä suorituskyky- ja tuottavuusetuja C++ -testiympäristössä verrattuna UVM-ympäristöön. 90.60% koodikattavuuden saavuttavien C++ testivektoreiden uudelleenimplementoiti UVM-ympäristössä tuotti 96.90% RTL-kattavuuden. C++-predictorin implementointi oli merkittävä työkalu RTL-kattavuustavoitteen saavuttamisessa

A new design methodology for mixed level and mixed signal simulation using PSpice A/D and VHDL

PSpice A/D is a simulation package that is used to analyze and predict the performance of analog and mixed signal circuits. It is very popular especially among Printed Circuit Board (PCB) engineers to verify board level designs. However, PSpice A/D currently lacks the ability to simulate analog components connected to digital circuits that are modeled using Hardware Descriptive Languages (HDLs), such as VHDL and Verilog HDL. Simulation of HDL models in PSpice A/D is necessary to verify mixed signal PCBs where programmable logic devices like Field Programmable Gate Arrays (FPGAs) and Complex Programmable Logic Devices (CPLDs) are connected to discrete analog components. More than 60% of the PCBs that are designed today contain at least one FPGA or CPLD. This thesis investigates the possibility of simulating VHDL models in PSpice A/D. A new design methodology and the necessary tools to achieve this goal are presented. The new design methodology achieves total system verification at PCB level. Total system verification reduces design failures and hence increases reliability. It also allows reducing the overall time to market. A mixed signal design from NASA Goddard Space Flight Center for a brushless three phase motor that runs a space application is implemented by following the proposed design methodology

Verification of Receiver Equalization by Integrating Dataflow Simulation and Physical Channels

This thesis combines Keysight’s SystemVue software with a Vector Signal Analyzer (VSA) and Vector Signal Generator (VSG) to test receiver equalization schemes over physical channels. The testing setup, “Equalization Verification,” is intended to be able to evaluate any equalization scheme over any physical channel, and a decision-directed feed-forward LMS equalizer is used as an example. The decision-directed feed-forward LMS equalizer is shown to decrease the BER from 10-2 to 10-3 (average of all trials) over a CAT7 and CAT6A cable, both simulated and physical, for 1GHz and 2GHz carrier, and 80MHz data rate. A wireless channel, 2.4GHz Dipole Antenna, is also tested to show that the addition of the equalization scheme decreases BER from 10-5 to less than 10-5. Then the simulation and equalization parameters (LMS step size, PRBS, etc.) are changed to further verify the equalization scheme. The simulated channel BER results do not always match the physical channel BER results, but the equalization scheme does decrease BER for both wired and wireless channels. Then transistor-based equalization model is created using both HDL SystemVue components and blocks easily implemented by transistors. The model is then verified using HDL, Spice, and SystemVue simulation. Overall this thesis accomplishes its goal of creating a testing setup, Equalization Verification, to show that adding a given simulated equalization scheme in SystemVue can improve the quality of the link, by decreasing BER by at least an order of magnitude, over a specific physical channel

FPGA BASED TIMING MODULE AND OPTICAL COMMUNICATION CARD DESIGN FOR SPALLATION NEUTRON SOURCE

The Timing Module and Optical Communication Card (OCC) are used for acquisition of neutron event data by the instrument systems at the Spallation Neutron Source (SNS) neutron scattering facility. The instrument systems produce a very large flux of neutrons of varying energies over a short time period through the spallation process. The Timing Module and OCC require high-bandwidth communication to ensure high-speed data movement to the memory in the data collection system without loss of neutron data. The existing implementations use a standard PCI-X bus interface to transfer the data between the cards and the host computer. The data processing on the existing cards is implemented in a Xilinx Virtex-II FPGA. The bandwidth restrictions of the PCI-X bus and the logic constraints of the Virtex-II FPGA have resulted in limited capabilities of the instrument systems. New designs for the timing and communication modules that will improve performance, avoid data loss, and provide for future logic expansion are desired. In this project, we redesign the Timing Module and OCC moving from a PCI-X to PCI-Express bus interface to improve the data acquisition bandwidth. The new design also uses a Xilinx Virtex-5 FPGA to allow more channels to be processed per card and provide for further expansion. Further, the Virtex-5 device also has an embedded PCI-Express Hard IP core. This internal core simplifies the Printed Circuit Board (PCB) design since there is no external PCI interface chip required and decreases the probability of errors between the PCI interface and user logic design. The Timing Module implements a simple PCI Express read and write for the data transfer. The OCC requires a higher data rate than the Timing Module and therefore uses a more complex bus master direct memory access (DMA) for the endpoint PCI-Express block, which allows for lower CPU utilization and higher performance. New user logic interfaces were designed to integrate the PCI-Express endpoint with the Timing Module and the OCC logic designs. A single PCB was designed to function as both the Timing Module and OCC. The logic designs were verified by both functional simulation and in-system JTAG signal capture on the new PCB. The results indicate that our design provides efficient data transfer, higher throughput, and scalability, benefitting both modules and meeting design requirements

Application of ethernet over powerline communication

Powerline communication (PLC) has seen notable demand due to its efficiency and the wide range of applications. It is a system for carrying data on a conductor that is also used for electric power transmission. In this thesis, this technique is used to implement a web server using the FPGA development board (DE 2). The information is sent through Ethernet over powerline. Using DE2 Altera kit, a webserver is created. The implementation of web server is done by first instantiating a Nios II system on the board. Nios II system is built around the Altera’s Nios II processor using the SOPC builder tool of the quartus II CAD tool. The SOPC builder tool generates the VHDL code of the defined system. The developed code is, then, configured in the FPGA board to instantiate the system. After implementing the Nios II system, an application program is run in the system to implement the web server. Ethernet packets are sent through the LAN cable over powerline. The output is taken from the Ethernet port and the fed into the Homeplug adapter. The packets are captured using wireshark packet sniffer and detailed analysis is done. This idea can be used for transmitting Ethernet packets over powerline using Homplug adapters

Manual for Automation of Dc-microgrid Component Using Matlab/Simulink and FPGA\u27s

Solar Energy is one of the abundantly available renewable energy source. Solar panels are semiconductor materials which capture the solar energy from every band in the visible light spectrum, infrared spectrum and ultra violet spectrum and converts it into electrical energy. The DC community microgrid is used to supplement utility electrical power supplied to the neighbored with renewable sources such as solar panels, emergency back-up power through batteries or generators. Smart Cloud Interconnected environment increases the standard of living and facilitates ease to rectify faults, debug components and reinstate or replace obsolete components with newer ones. Automation of the DC microgrid components provides a simple yet efficient way to connect to the grid and to every component in the grid remotely. It is essential to find the node of failure in the grid for technicians and engineers to work on and to debug the issue to facilitate smooth running of the grid without shutdown. FPGAs are used as target devices for end synthesis of the model that is created on Simulink. These FPGAs are links between cloud and power electronics components. To utilize the energy resource efficiently we need to monitor the input and output of every component at every node in the grid. Simulating models on Simulink will let us connect the component and test engineer to the grid to detect any flaws or failures on time. FPGAs are easily reprogrammable and have long life with excellent capability to withstand stress. This thesis report provides a set of procedures to create and simulate a real time component model and to generate HDL files to build a clean code which can be redeployed on target FPGAs