Design Techniques for High Speed Low Voltage and Low Power Non-Calibrated Pipeline Analog to Digital Converters

The profound digitization of modern microelectronic modules made Analog-to- Digital converters (ADC) key components in many systems. With resolutions up to 14bits and sampling rates in the 100s of MHz, the pipeline ADC is a prime candidate for a wide range of applications such as instrumentation, communications and consumer electronics. However, while past work focused on enhancing the performance of the pipeline ADC from an architectural standpoint, little has been done to individually address its fundamental building blocks. This work aims to achieve the latter by proposing design techniques to improve the performance of these blocks with minimal power consumption in low voltage environments, such that collectively high performance is achieved in the pipeline ADC. Towards this goal, a Recycling Folded Cascode (RFC) amplifier is proposed as an enhancement to the general performance of the conventional folded cascode. Tested in Taiwan Semiconductor Manufacturing Company (TSMC) 0.18?m Complementary Metal Oxide Semiconductor (CMOS) technology, the RFC provides twice the bandwidth, 8-10dB additional gain, more than twice the slew rate and improved noise performance over the conventional folded cascode-all at no additional power or silicon area. The direct auto-zeroing offset cancellation scheme is optimized for low voltage environments using a dual level common mode feedback (CMFB) circuit, and amplifier differential offsets up to 50mV are effectively cancelled. Together with the RFC, the dual level CMFB was used to implement a sample and hold amplifier driving a singleended load of 1.4pF and using only 2.6mA; at 200MS/s better than 9bit linearity is achieved. Finally a power conscious technique is proposed to reduce the kickback noise of dynamic comparators without resorting to the use of pre-amplifiers. When all techniques are collectively used to implement a 1Vpp 10bit 160MS/s pipeline ADC in Semiconductor Manufacturing International Corporation (SMIC) 0.18[mu]m CMOS, 9.2 effective number of bits (ENOB) is achieved with a near Nyquist-rate full scale signal. The ADC uses an area of 1.1mm2 and consumes 42mW in its analog core. Compared to recent state-of-the-art implementations in the 100-200MS/s range, the presented pipeline ADC uses the least power per conversion rated at 0.45pJ/conversion-step

An 8-Bit Analog-to-Digital Converter for Battery Operated Wireless Sensor Nodes

Wireless sensing networks (WSNs) collect analog information transduced into the form of a voltage or current. This data is typically converted into a digital representation of the value and transmitted wirelessly using various modulation techniques. As the available power and size is limited for wireless sensor nodes in many applications, a medium resolution Analog-to-Digital Converter (ADC) is proposed to convert a sensed voltage with moderate speeds to lower power consumption. Specifications also include a rail-to-rail input range and minimized errors associated with offset, gain, differential nonlinearity, and integral nonlinearity. To achieve these specifications, an 8-bit successive approximation register ADC is developed which has a conversion time of nine clock cycles. This ADC features a charge scaling array included to achieve minimized power consumption and area by reducing unit capacitance in the digital-to-analog converter. Furthermore, a latched comparator provides fast decisions utilizing positive feedback. The ADC was designed and simulated using Cadence Virtuoso with parasitic extraction over expected operating temperature range of 0 – 85°C. The design was fabricated using TSMC’s 65 nanometer RF GP process and tested on a printed circuit board to verify design specifications. The measured results for the device show an offset and gain error of +7 LSB and 31.1 LSB, respectively, and a DNL range of -0.9 LSB to +0.8 LSB and an INL range of approximately -4.6 LSB to +12 LSB. The INL is much improved in regard to the application of the temperature sensor. The INL for this region of interest is from -3.5 LSB to +2.8 LSB

Design Techniques for High Speed Low Voltage and Low Power Non-Calibrated Pipeline Analog to Digital Converters

The profound digitization of modern microelectronic modules made Analog-to- Digital converters (ADC) key components in many systems. With resolutions up to 14bits and sampling rates in the 100s of MHz, the pipeline ADC is a prime candidate for a wide range of applications such as instrumentation, communications and consumer electronics. However, while past work focused on enhancing the performance of the pipeline ADC from an architectural standpoint, little has been done to individually address its fundamental building blocks. This work aims to achieve the latter by proposing design techniques to improve the performance of these blocks with minimal power consumption in low voltage environments, such that collectively high performance is achieved in the pipeline ADC. Towards this goal, a Recycling Folded Cascode (RFC) amplifier is proposed as an enhancement to the general performance of the conventional folded cascode. Tested in Taiwan Semiconductor Manufacturing Company (TSMC) 0.18?m Complementary Metal Oxide Semiconductor (CMOS) technology, the RFC provides twice the bandwidth, 8-10dB additional gain, more than twice the slew rate and improved noise performance over the conventional folded cascode-all at no additional power or silicon area. The direct auto-zeroing offset cancellation scheme is optimized for low voltage environments using a dual level common mode feedback (CMFB) circuit, and amplifier differential offsets up to 50mV are effectively cancelled. Together with the RFC, the dual level CMFB was used to implement a sample and hold amplifier driving a singleended load of 1.4pF and using only 2.6mA; at 200MS/s better than 9bit linearity is achieved. Finally a power conscious technique is proposed to reduce the kickback noise of dynamic comparators without resorting to the use of pre-amplifiers. When all techniques are collectively used to implement a 1Vpp 10bit 160MS/s pipeline ADC in Semiconductor Manufacturing International Corporation (SMIC) 0.18[mu]m CMOS, 9.2 effective number of bits (ENOB) is achieved with a near Nyquist-rate full scale signal. The ADC uses an area of 1.1mm2 and consumes 42mW in its analog core. Compared to recent state-of-the-art implementations in the 100-200MS/s range, the presented pipeline ADC uses the least power per conversion rated at 0.45pJ/conversion-step

Capacitance-to-Digital Converter for Ultra-Low-Power Wireless Sensor Nodes

Power consumption is one of the main design constraints in today’s integrated circuits. For systems like wearable electronics, UAVs, IOT systems powered by batteries which are charged using the energy harvested from various sources like RF, Thermal, Solar and Vibration, ultra-low power consumption is paramount. In these systems, Transducers which convert physical parameters into electrical parameters and the analog-to-digital converters (ADCs) are key components as the interface between the analog world and the digital domain. This thesis addresses the design challenges, strategies, as well as circuit techniques of ultra-low-power signal Front End used in several low power electronic systems in general and pressure measurement systems in particular. In this thesis, Capacitance to Digital Converter based pressure measurement system has been implemented. Here we present a general-purpose, wide-range CDC that combines a correlated double sampling (CDS) approach with a differential asynchronous SAR ADC. Since the sensor capacitor is sampled only twice per conversion, energy per conversion is low. Furthermore, since the CDS separates the sensor capacitor from the CDAC, a full differential input voltage range is preserved. The CDC has a 2.5-to-75.5pF conversion range. Monotonic SAR ADC was designed in 180nm CMOS with 1-V power supply and a 1-kS/s sampling rate with switching energy of about 100nW

A Novel High Speed Cmos Comparator With Low Power Disipation And Low Offset

A Novel High Speed CMOS Comparator with low power dissipation, low offset, low noise and high speed is proposed. Inputs are reconfigured from typical differential pair comparator such that near equal current distribution in the input transistors can be achieved for a meta-stable point of the comparator. Restricted signal swing clock for the tail current is also used to ensure constant currents in the differential pairs. Nearly 18 mv offset voltage is easily achieved with the proposed structure making it favourable for flash and pipeline data conversion applications. The proposed topology is based on hysteresis using positive feedback, has a small power dissipation, less area, and it is shown to be very robust against transistor mismatch, noise immunity. Test structures of the comparators, designed in GPDK 90 nm are measured to determine offset –voltage, power - dissipation and speed. These are compared and the superior features of the proposed comparator are established

Digital Background Self-Calibration Technique for Compensating Transition Offsets in Reference-less Flash ADCs

This Dissertation focusses on proving that background calibration using adaptive algorithms are low-cost, stable and effective methods for obtaining high accuracy in flash A/D converters. An integrated reference-less 3-bit flash ADC circuit has been successfully designed and taped out in UMC 180 nm CMOS technology in order to prove the efficiency of our proposed background calibration. References for ADC transitions have been virtually implemented built-in in the comparators dynamic-latch topology by a controlled mismatch added to each comparator input front-end. An external very simple DAC block (calibration bank) allows control the quantity of mismatch added in each comparator front-end and, therefore, compensate the offset of its effective transition with respect to the nominal value. In order to assist to the estimation of the offset of the prototype comparators, an auxiliary A/D converter with higher resolution and lower conversion speed than the flash ADC is used: a 6-bit capacitive-DAC SAR type. Special care in synchronization of analogue sampling instant in both ADCs has been taken into account. In this thesis, a criterion to identify the optimum parameters of the flash ADC design with adaptive background calibration has been set. With this criterion, the best choice for dynamic latch architecture, calibration bank resolution and flash ADC resolution are selected. The performance of the calibration algorithm have been tested, providing great programmability to the digital processor that implements the algorithm, allowing to choose the algorithm limits, accuracy and quantization errors in the arithmetic. Further, systematic controlled offset can be forced in the comparators of the flash ADC in order to have a more exhaustive test of calibration

Low power encoder and comparator design of 5-bit flash ADC

The present work of the thesis is divided into two parts, first is design of a low power encoder and second is low power latched comparator design. In this low power encoding scheme proposed for 4GS/s 5 bit flash analog to digital converter. The demanding issues in the design of a low power flash ADC is the design of thermometer code to binary code. An encoder in this thesis converts the thermo-meter code into binary code without any intermediate stage using dynamic CMOS logic. To decrease the power consumption of the Flash ADC, the implementation of encoder and comparator is done using dynamic CMOS logic. The proposed encoder in this thesis is designed using 90nm technology at 1.2V DC voltage source using CADENCE tool. The simulation results of 5-bit Flash ADC block is shown for a sampling frequency up to 4GHz and at 4GHz the encoder circuit showing the average power dissipation of the encoder block is 1.833 µW.The other part of the present work is the design of low power comparator for the 5-bit flash ADC. Dynamic latch comparator has been designed in order to reduce power dissipation, delays etc. The different parts of the dynamic latch comparator like: pre-amplifier, dynamic latch, and output buffer are implemented on CADENCE tool with 1.2 V power supply. The simulation results shown for a sampling frequency of 5 GHz and the average power dissipation of the proposed comparator is 69.09 µW. The physical layout of the encoder and comparator has been drawn using CADENCE VIRTUSO LAYOUT EDITOR. The DRC errors has been removed and the layout has been matched with the schematics

Analog baseband circuits for sensor systems

This thesis is composed of six publications and an overview of the research topic, which also summarizes the work. The research presented in this thesis focuses on research into analog baseband circuits for sensor systems. The research is divided into three different topics: the integration of analog baseband circuits into a radio receiver for sensor applications; the integration of an ΔΣ modulator A/D converter into a GSM/WCDMA radio receiver for mobile phones, and the integration of algorithmic A/D converters for a capacitive micro-accelerometer interface. All the circuits are implemented using deep sub-micron CMOS technologies. The work summarizes the design of different blocks for sensor systems. The research into integrated analog baseband circuits for a radio receiver focuses on a circuit structures with a very low power dissipation and that can be implemented using only standard CMOS technologies. The research into integrated ΔΣ modulator A/D converter design for a GSM/WCDMA radio receiver for mobile phones focuses on the implications for analog circuit design emerging from using a very deep sub-micron CMOS process. Finally, in the research into algorithmic A/D converters for a capacitive microaccelerometer interface, new ways of achieving a good performance with low power dissipation, while also minimizing the silicon area of the integrated A/D converter are introduced

A Mixed-Signal Demodulator for a Low-Complexity IR-UWB Receiver: Methodology, Simulation and Design

This works presents an integrated 0.18μm CMOS 2-PPM demodulator based on a switched capacitor network for an Energy Detection Impulse-Radio UWB receiver. The circuit has been designed using a top-down methodology that allows to discover the impact of low-level non-idealities on system-level performance. Through the use of a mixed signal simulation environment, performance figures have been obtained which helped evaluate the influence at system-level of the non-idealities of the most critical block. Results show that the circuit allows the replacement of the ADC typically employed in Energy Detection receivers and provides about infinite equivalent quantization resolution. The demodulator achieves 190 pJ/bit at 1.8V

Energy aware ultra-low power SAR ADC in 180nm CMOS for biomedical application

Power consumption is one of the main design constraints in today’s integrated circuits. For systems powered by batteries, such as implantable biomedical devices, ultra-low power consumption is paramount. In these systems, analog-to-digital converters (ADCs) are key components as the interface between the analog world and the digital domain. This thesis addresses the design challenges, strategies, as well as circuit techniques of ultra-low-power ADCs for medical implant devices. In this thesis four architectures of SAR ADC is implemented with different energy efficiency. In first architecture, conventional SAR ADC was designed in 180nm CMOS technology with a 1-V power supply and a 1-kS/s sampling rate for monitoring bio potential signals, the ADC achieves a signal-to-noise and distortion ratio of 57.16 dB and consumes 43 nW power, resulting in a figure of merit of 73 fJ/conversion-step. In second architecture, Split capacitor SAR ADC was designed in 180nm CMOS with same resolution and sampling speed