2 research outputs found
TIME AND FREQUENCY CHARACTERISTIC OF 802.11AX
Wireless Local Area Network (WLAN) is a wireless communication system that connects two or more devices using radio frequency to form a local network (LAN). WLAN is used inside buildings (e.g., apartment, campus, train station). Unlike
Ethernet, The first WLAN standard, namely IEEE 802.11b, was released in the 1990s. Maximum achievable data rate
is 11 Mbps for 802.11b. The most recent version is 802.11ax with maximum throughput of 3.46 Gbps. This thesis reports network throughput, jitter, and delay performance of IEEE 802.11ax experimentally measured and analyzed under various conditions (SNR, window size and packet length). It also gives an empirical model to simulate the behavior of 802.11ax network throughput and jitter
Backhaul steering em dual band WiFi Mesh
Over the years, WiFi became an essential technology to most people. The success
of the introduction of wireless devices with WiFi connectivity like laptops, smartphones,
IoT sensors and others, increased the demand for better WiFi networks.
Since many people have and use WiFi networks in their homes, jobs and in public
places, this is an area that draws a lot of attention. The networks need better
service and better coverage. To solve this challenge, WiFi Alliance developed WiFi
EasyMesh, a standard for WiFi networks that utilize multiple access points that allow
an easy setup and compatibility with WiFi certified devices. This technology is
able to create wireless mesh networks over the WiFi protocol to increase the signal
coverage. Besides this solution, the release of a new WiFi standard (WiFi 6) was
also important. This new release improved the overall rates a WiFi transmission
can achieve, and also introduced a set of new features that positively impact the
users.
This dissertation’s main objectives were to show that the use of several frequencies
(2.4GHz and 5GHz) in the backhaul links of a mesh network could increase
the overall performance, and to create and test a mechanism that would adapt
the network topology when needed. After defining several scenarios and executing
them, the obtained results showed that there are in fact situations where the use
of a different frequency (2.4GHz) beyond 5GHz would increase the network’s performance.
The scenarios tested multiple aspects on the mesh network such as the
amount of traffic, the number of hops and frequency used by each link. The proposed
mechanism showed that it was capable of identifying the need to change the
network and actually change it in run-time, so it could benefit from the adoption
of a new backhaul topology.Ao longo dos anos, a tecnologia WiFi tornou-se uma tecnologia essencial para a
maioria das pessoas. O sucesso da indrodução de dispositivos com conectividade
WiFi como computadores, smartphones e sensores IoT causou uma maior necessidade
de melhores redes WiFi. Como muitas pessoas utilizam estas redes na sua
casa, no seu trabalho e em locais públicos, existe uma maior atenção para esta área
das telecomunicações. Estas redes começaram a necessitar de melhor serviço e de
melhor cobertura. Para resolver este desafio, a WiFi Alliance desenvolveu o WiFi
EasyMesh, uma norma que utiliza múltiplos pontos de acesso que permitem ter
um setup rápido e fácil (em dispositivos compativeis com WiFi). Esta tecnologia
permite criar uma rede mesh para aumentar a cobertura de uma rede WiFi. Para
além desta solução, a introdução do standard 802.11ax (WiFi 6) foi bastante importante
para melhorar a qualidade dos serviços. Para além do aumento das taxas
máximas nas transmições, esta norma também introduziu novas funcionalidades
que têm impacto positivo nos utilizadores.
Esta dissertação tem como objetivos mostrar que a utilização de várias frequências
(5GHz e 2.4GHz) nas ligações de Backhaul de uma rede mesh podem melhorar o
desempenho da mesma, e também desenvolver um mechanismo capaz de alterar e
adaptar a rede às suas necessidades. Depois de desenvolver e testar vários cenários,
foi comprovado que de facto a utilização de uma ligação em 2.4GHz, além da de
5GHz, poderia melhorar o desempenho da rede. Estes cenários testaram vários
aspetos como a quantidade de tráfego na rede, o número de saltos e a frequência
utilizada. O mecanismo proposto mostrou ser capaz de identificar cenários onde
era necessário alterar a topologia da rede em funcionamento, e também mostrou
conseguir realizar as alterações na rede mesh.Mestrado em Engenharia de Computadores e Telemátic