A Markovian influence graph formed from utility line outage data to mitigate large cascades

We use observed transmission line outage data to make a Markovian influence graph that describes the probabilities of transitions between generations of cascading line outages. Each generation of a cascade consists of a single line outage or multiple line outages. The new influence graph defines a Markov chain and generalizes previous influence graphs by including multiple line outages as Markov chain states. The generalized influence graph can reproduce the distribution of cascade size in the utility data. In particular, it can estimate the probabilities of small, medium and large cascades. The influence graph has the key advantage of allowing the effect of mitigations to be analyzed and readily tested, which is not available from the observed data. We exploit the asymptotic properties of the Markov chain to find the lines most involved in large cascades and show how upgrades to these critical lines can reduce the probability of large cascades

Railway bridge structural health monitoring and fault detection: state-of-the-art methods and future challenges

Railway importance in the transportation industry is increasing continuously, due to the growing demand of both passenger travel and transportation of goods. However, more than 35% of the 300,000 railway bridges across Europe are over 100-years old, and their reliability directly impacts the reliability of the railway network. This increased demand may lead to higher risk associated with their unexpected failures, resulting safety hazards to passengers and increased whole life cycle cost of the asset. Consequently, one of the most important aspects of evaluation of the reliability of the overall railway transport system is bridge structural health monitoring, which can monitor the health state of the bridge by allowing an early detection of failures. Therefore, a fast, safe and cost-effective recovery of the optimal health state of the bridge, where the levels of element degradation or failure are maintained efficiently, can be achieved. In this article, after an introduction to the desired features of structural health monitoring, a review of the most commonly adopted bridge fault detection methods is presented. Mainly, the analysis focuses on model-based finite element updating strategies, non-model-based (data-driven) fault detection methods, such as artificial neural network, and Bayesian belief network–based structural health monitoring methods. A comparative study, which aims to discuss and compare the performance of the reviewed types of structural health monitoring methods, is then presented by analysing a short-span steel structure of a railway bridge. Opportunities and future challenges of the fault detection methods of railway bridges are highlighted

BAYESIAN KERNEL METHODS FOR THE RISK ANALYSIS AND RESILIENCE MODELING OF CRITICAL INFRASTRUCTURE SYSTEMS

The protection of critical infrastructures has recently garnered attention with an emphasis on analyzing the risk and improving the resilience of such systems. With the abundance of data, risk managers should be able to better inform preparedness and recovery decision making under uncertainty. It is important, however, to develop and utilize the necessary methodologies that bridge between data and decisions. The goal of this dissertation is to (i) predict the likelihood of risk, (ii) assess the consequences of a disruption, and (iii) inform preparedness and recovery decision making. This research presents a data-driven analysis of the risk and resilience of critical infrastructure systems. First, a new Bayesian kernel model is developed to predict the frequency of failures and a Beta Bayesian kernel model is deployed to model resilience-based importance measures. Bayesian kernel models were developed for Gaussian distributions and later extended to other continuous probability distributions. This research develops a Poisson Bayesian kernel model to accommodate count data. Second, interdependency models are integrated with decision analysis and resilience quantification techniques to assess the multi-industry economic impact of critical infrastructure resilience and inform preparedness and recovery decision making under uncertainty. Examples of critical infrastructure systems are inland waterways, which are critical elements in the nation’s civil infrastructure and the world’s supply chain. They allow for a cost-effective flow of approximately $150 billion worth of commodities annually across industries and geographic locations, which is why they are called “inland marine highways.” Aging components (i.e., locks and dams) combined with adverse weather conditions, affect the reliability and resilience of inland waterways. Frequent disruptions and lengthy recovery times threaten regional commodity flows, and more broadly, multiple industries that rely on those commodities. While policymakers understand the increasing need for inland waterway rehabilitation and preparedness investment, resources are limited and select projects are funded each year to improve only certain components of the network. As a result, a number of research questions arise. What is the impact of infrastructure systems disruptions, and how to predict them? What metrics should be used to identify critical components and determine the system’s resilience? What are the best risk management strategies in terms of preparedness investment and recovery prioritization? A Poisson Bayesian kernel model is developed and deployed to predict the frequency of locks and dams closures. Economic dynamic interdependency models along with stochastic inoperability multiobjective decision trees and resilience metrics are used to assess the broader impact of a disruption resulting in the closure of a port or a link of the river and impacting multiple interdependent industries. Stochastic resilience-based measures are analyzed to determine the critical waterway components, more specifically locks and dams, that contribute to the overall waterway system resilience. A data-driven case study illustrates these methods to describe commodity flows along the various components of the U.S. Mississippi River Navigation System and employs them to motivate preparedness and recovery strategies

Real-time Traffic Safety Evaluation Models And Their Application For Variable Speed Limits

Traffic safety has become the first concern in the transportation area. Crashes have cause extensive human and economic losses. With the objective of reducing crash occurrence and alleviating crash injury severity, major efforts have been dedicated to reveal the hazardous factors that affect crash occurrence at both the aggregate (targeting crash frequency per segment, intersection, etc.,) and disaggregate levels (analyzing each crash event). The aggregate traffic safety studies, mainly developing safety performance functions (SPFs), are being conducted for the purpose of unveiling crash contributing factors for the interest locations. Results of the aggregate traffic safety studies can be used to identify crash hot spots, calculate crash modification factors (CMF), and improve geometric characteristics. Aggregate analyses mainly focus on discovering the hazardous factors that are related to the frequency of total crashes, of specific crash type, or of each crash severity level. While disaggregate studies benefit from the reliable surveillance systems which provide detailed real-time traffic and weather data. This information could help in capturing microlevel influences of the hazardous factors which might lead to a crash. The disaggregate traffic safety models, also called real-time crash risk evaluation models, can be used in monitoring crash hazardousness with the real-time field data fed in. One potential use of real-time crash risk evaluation models is to develop Variable Speed Limits (VSL) as a part of a freeway management system. Models have been developed to predict crash occurrence to proactively improve traffic safety and prevent crash occurrence. iv In this study, first, aggregate safety performance functions were estimated to unveil the different risk factors affecting crash occurrence for a mountainous freeway section. Then disaggregate real-time crash risk evaluation models have been developed for the total crashes with both the machine learning and hierarchical Bayesian models. Considering the need for analyzing both aggregate and disaggregate aspects of traffic safety, systematic multi-level traffic safety studies have been conducted for single- and multi-vehicle crashes, and weekday and weekend crashes. Finally, the feasibility of utilizing a VSL system to improve traffic safety on freeways has been investigated. This research was conducted based on data obtained from a 15-mile mountainous freeway section on I-70 in Colorado. The data contain historical crash data, roadway geometric characteristics, real-time weather data, and real-time traffic data. Real-time weather data were recorded by 6 weather stations installed along the freeway section, while the real-time traffic data were obtained from the Remote Traffic Microwave Sensor (RTMS) radars and Automatic Vechicle Identification (AVI) systems. Different datasets have been formulated from various data sources, and prepared for the multi-level traffic safety studies. In the aggregate traffic safety investigation, safety performance functions were developed to identify crash occurrence hazardous factors. For the first time real-time weather and traffic data were used in SPFs. Ordinary Poisson model and random effects Poisson models with Bayesian inference approach were employed to reveal the effects of weather and traffic related variables on crash occurrence. Two scenarios were considered: one seasonal based case and one crash type v based case. Deviance Information Criterion (DIC) was utilized as the comparison criterion; and the correlated random effects Poisson models outperform the others. Results indicate that weather condition variables, especially precipitation, play a key role in the safety performance functions. Moreover, in order to compare with the correlated random effects Poisson model, Multivariate Poisson model and Multivariate Poisson-lognormal model have been estimated. Conclusions indicate that, instead of assuming identical random effects for the homogenous segments, considering the correlation effects between two count variables would result in better model fit. Results from the aggregate analyses shed light on the policy implication to reduce crash frequencies. For the studied roadway segment, crash occurrence in the snow season have clear trends associated with adverse weather situations (bad visibility and large amount of precipitation); weather warning systems can be employed to improve road safety during the snow season. Furthermore, different traffic management strategies should be developed according to the distinct seasonal influence factors. In particular, sites with steep slopes need more attention from the traffic management center and operators especially during snow seasons to control the excess crash occurrence. Moreover, distinct strategy of freeway management should be designed to address the differences between single- and multi-vehicle crash characteristics. In addition to developing safety performance functions with various modeling techniques, this study also investigates four different approaches of developing informative priors for the independent variables. Bayesian inference framework provides a complete and coherent way to balance the empirical data and prior expectations; merits of these informative priors have been tested along with two types of Bayesian hierarchical models (Poisson-gamma and Poisson- vi lognormal models). Deviance Information Criterion, R-square values, and coefficients of variance for the estimations were utilized as evaluation measures to select the best model(s). Comparisons across the models indicate that the Poisson-gamma model is superior with a better model fit and it is much more robust with the informative priors. Moreover, the two-stage Bayesian updating informative priors provided the best goodness-of-fit and coefficient estimation accuracies. In addition to the aggregate analyses, real-time crash risk evaluation models have been developed to identify crash contributing factors at the disaggregate level. Support Vector Machine (SVM), a recently proposed statistical learning model and Hierarchical Bayesian logistic regression models were introduced to evaluate real-time crash risk. Classification and regression tree (CART) model has been developed to select the most important explanatory variables. Based on the variable selection results, Bayesian logistic regression models and SVM models with different kernel functions have been developed. Model comparisons based on receiver operating curves (ROC) demonstrate that the SVM model with Radial basis kernel function outperforms the others. Results from the models demonstrated that crashes are likely to happen during congestion periods (especially when the queuing area has propagated from the downstream segment); high variation of occupancy and/or volume would increase the probability of crash occurrence. Moreover, effects of microscopic traffic, weather, and roadway geometric factors on the occurrence of specific crash types have been investigated. Crashes have been categorized as rear- vii end, sideswipe, and single-vehicle crashes. AVI segment average speed, real-time weather data, and roadway geometric characteristics data were utilized as explanatory variables. Conclusions from this study imply that different active traffic management (ATM) strategies should be designed for three- and two-lane roadway sections and also considering the seasonal effects. Based on the abovementioned results, real-time crash risk evaluation models have been developed separately for multi-vehicle and single-vehicle crashes, and weekday and weekend crashes. Hierarchical Bayesian logistic regression models (random effects and random parameter logistic regression models) have been introduced to address the seasonal variations, crash unit level’s diversities, and unobserved heterogeneity caused by geometric characteristics. For the multi-vehicle crashes: congested conditions at downstream would contribute to an increase in the likelihood of multi-vehicle crashes; multi-vehicle crashes are more likely to occur during poor visibility conditions and if there is a turbulent area that exists downstream. Drivers who are unable to reduce their speeds timely are prone to causing rear-end crashes. While for the singlevehicle crashes: slow moving traffic platoons at the downstream detector of the crash occurrence locations would increase the probability of single-vehicle crashes; large variations of occupancy downstream would also increase the likelihood of single-vehicle crash occurrence. Substantial efforts have been dedicated to revealing the hazardous factors that affect crash occurrence from both the aggregate and disaggregate level in this study, however, findings and conclusions from these research work need to be transferred into applications for roadway design and freeway management. This study further investigates the feasibility of utilizing Variable Speed Limits (VSL) system, one key part of ATM, to improve traffic safety on freeways. A proactive traffic safety improvement VSL control algorithm has been proposed. First, an viii extension of the traffic flow model METANET was employed to predict traffic flow while considering VSL’s impacts on the flow-density diagram; a real-time crash risk evaluation model was then estimated for the purpose of quantifying crash risk; finally, the optimal VSL control strategies were achieved by employing an optimization technique of minimizing the total predicted crash risks along the VSL implementation area. Constraints were set up to limit the increase of the average travel time and differences between posted speed limits temporarily and spatially. The proposed VSL control strategy was tested for a mountainous freeway bottleneck area in the microscopic simulation software VISSIM. Safety impacts of the VSL system were quantified as crash risk improvements and speed homogeneity improvements. Moreover, three different driver compliance levels were modeled in VISSIM to monitor the sensitivity of VSL’s safety impacts on driver compliance levels. Conclusions demonstrate that the proposed VSL system could effectively improve traffic safety by decreasing crash risk, enhancing speed homogeneity, and reducing travel time under both high and moderate driver compliance levels; while the VSL system does not have significant effects on traffic safety enhancement under the low compliance scenario. Future implementations of VSL control strategies and related research topics were also discussed