Development of Eco-Friendly Ramp Control for Connected and Automated Electric Vehicles

With on-board sensors such as camera, radar, and Lidar, connected and automated vehicles (CAVs) can sense the surrounding environment and be driven autonomously and safely by themselves without colliding into other objects on the road. CAVs are also able to communicate with each other and roadside infrastructure via vehicle-to-vehicle and vehicle-to-infrastructure communications, respectively, sharing information on the vehicles’ states, signal phase and timing (SPaT) information, enabling CAVs to make decisions in a collaborative manner. As a typical scenario, ramp control attracts wide attention due to the concerns of safety and mobility in the merging area. In particular, if the line-of-the-sight is blocked (because of grade separation), then neither mainline vehicles nor on-ramp vehicles may well adapt their own dynamics to perform smoothed merging maneuvers. This may lead to speed fluctuations or even shockwave propagating upstream traffic along the corridor, thus potentially increasing the traffic delays and excessive energy consumption. In this project, the research team proposed a hierarchical ramp merging system that not only allowed microscopic cooperative maneuvers for connected and automated electric vehicles on the ramp to merge into mainline traffic flow, but also had controllability of ramp inflow rate, which enabled macroscopic traffic flow control. A centralized optimal control-based approach was proposed to both smooth the merging flow and improve the system-wide mobility of the network. Linear quadratic trackers in both finite horizon and receding horizon forms were developed to solve the optimization problem in terms of path planning and sequence determination, and a microscopic electric vehicle (EV) energy consumption model was applied to estimate the energy consumption. The simulation results confirmed that under the regulated inflow rate, the proposed system was able to avoid potential traffic congestion and improve the mobility (in terms of average speed) as much as 115%, compared to the conventional ramp metering and the ramp without any control approach. Interestingly, for EVs (connected and automated EVs in this study), the improved mobility may not necessarily result in the reduction of energy consumption. The “sweet spot” of average speed ranges from 27–34 mph for the EV models in this study.View the NCST Project Webpag

Using mobility information to perform a feasibility study and the evaluation of spatio-temporal energy demanded by an electric taxi fleet

Half of the global population already lives in urban areas, facing to the problem of air pollution mainly caused by the transportation system. The recently worsening of urban air quality has a direct impact on the human health. Replacing today’s internal combustion engine vehicles with electric ones in public fleets could provide a deep impact on the air quality in the cities. In this paper, real mobility information is used as decision support for the taxi fleet manager to promote the adoption of electric taxi cabs in the city of San Francisco, USA. Firstly, mobility characteristics and energy requirements of a single taxi are analyzed. Then, the results are generalized to all vehicles from the taxi fleet. An electrificability rate of the taxi fleet is generated, providing information about the number of current trips that could be performed by electric taxis without modifying the current driver mobility patterns. The analysis results reveal that 75.2% of the current taxis could be replaced by electric vehicles, considering a current standard battery capacity (24–30 kWh). This value can increase significantly (to 100%), taking into account the evolution of the price and capacity of the batteries installed in the last models of electric vehicles that are coming to the market. The economic analysis shows that the purchasing costs of an electric taxi are bigger than conventional one. However, fuel, maintenance and repair costs are much lower. Using the expected energy consumption information evaluated in this study, the total spatio-temporal demand of electric energy required to recharge the electric fleet is also calculated, allowing identifying optimal location of charging infrastructure based on realistic routing patterns. This information could also be used by the distribution system operator to identify possible reinforcement actions in the electric grid in order to promote introducing electric vehicles

Electric vehicle battery model identification and state of charge estimation in real world driving cycles

This paper describes a study demonstrating a new method of state-of-charge (SoC) estimation for batteries in real-world electric vehicle applications. This method combines realtime model identification with an adaptive neuro-fuzzy inference system (ANFIS). In the study, investigations were carried down on a small-scale battery pack. An equivalent circuit network model of the pack was developed and validated using pulse-discharge experiments. The pack was then subjected to demands representing realistic WLTP and UDDS driving cycles obtained from a model of a representative electric vehicle, scaled match the size of the battery pack. A fast system identification technique was then used to estimate battery parameter values. One of these, open circuit voltage, was selected as suitable for SoC estimation, and this was used as the input to an ANFIS system which estimated the SoC. The results were verified by comparison to a theoretical Coulomb-counting method, and the new method was judged to be effective. The case study used a small 7.2 V NiMH battery pack, but the method described is applicable to packs of any size or chemistry

Nonlinear observers for predicting state-of-charge and state-of-health of lead-acid batteries for hybrid-electric vehicles

Abstract—This paper describes the application of state-estimation techniques for the real-time prediction of the state-of-charge (SoC) and state-of-health (SoH) of lead-acid cells. Specifically, approaches based on the well-known Kalman Filter (KF) and Extended Kalman Filter (EKF), are presented, using a generic cell model, to provide correction for offset, drift, and long-term state divergence—an unfortunate feature of more traditional coulomb-counting techniques. The underlying dynamic behavior of each cell is modeled using two capacitors (bulk and surface) and three resistors (terminal, surface, and end), from which the SoC is determined from the voltage present on the bulk capacitor. Although the structure of the model has been previously reported for describing the characteristics of lithium-ion cells, here it is shown to also provide an alternative to commonly employed models of lead-acid cells when used in conjunction with a KF to estimate SoC and an EKF to predict state-of-health (SoH). Measurements using real-time road data are used to compare the performance of conventional integration-based methods for estimating SoC with those predicted from the presented state estimation schemes. Results show that the proposed methodologies are superior to more traditional techniques, with accuracy in determining the SoC within 2% being demonstrated. Moreover, by accounting for the nonlinearities present within the dynamic cell model, the application of an EKF is shown to provide verifiable indications of SoH of the cell pack

Observer techniques for estimating the state-of-charge and state-of-health of VRLABs for hybrid electric vehicles

The paper describes the application of observer-based state-estimation techniques for the real-time prediction of state-of-charge (SoC) and state-of-health (SoH) of lead-acid cells. Specifically, an approach based on the well-known Kalman filter, is employed, to estimate SoC, and the subsequent use of the EKF to accommodate model non-linearities to predict battery SoH. The underlying dynamic behaviour of each cell is based on a generic Randles' equivalent circuit comprising of two-capacitors (bulk and surface) and three resistors, (terminal, transfer and self-discharging). The presented techniques are shown to correct for offset, drift and long-term state divergence-an unfortunate feature of employing stand-alone models and more traditional coulomb-counting techniques. Measurements using real-time road data are used to compare the performance of conventional integration-based methods for estimating SoC, with those predicted from the presented state estimation schemes. Results show that the proposed methodologies are superior with SoC being estimated to be within 1% of measured. Moreover, by accounting for the nonlinearities present within the dynamic cell model, the application of an EKF is shown to provide verifiable indications of SoH of the cell pack

Transportation Futures: Policy Scenarios for Achieving Greenhouse Gas Reduction Targets, MNTRC Report 12-11

It is well established that GHG emissions must be reduced by 50% to 80% by 2050 in order to limit global temperature increase to 2°C. Achieving reductions of this magnitude in the transportation sector is a challenge and requires a multitude of policies and technology options. The research presented here analyzes three scenarios: changes in the perceived price of travel, land-use intensification, and increases in transit. Elasticity estimates are derived using an activity-based travel model for the state of California and broadly representative of the U.S. The VISION model is used to forecast changes in technology and fuel options that are currently forecast to occur in the U.S., providing a life cycle GHG forecast for the road transportation sector. Results suggest that aggressive policy action is needed, especially pricing policies, but also more on the technology side. Medium- and heavy-duty vehicles are in particular need of additional fuel or technology-based GHG reductions