5 research outputs found
Transient and Permanent Error Control for High-End Multiprocessor Systems-on-Chip
High-end MPSoC systems with built-in high-radix topologies achieve good performance because of the improved connectivity and the reduced network diameter. In high-end MPSoC systems, fault tolerance support is becoming a compulsory feature. In this work, we propose a combined method to address permanent and transient link and router failures in those systems. The LBDRhr mechanism is proposed to tolerate permanent link failures in some popular high-radix topologies. The increased router complexity may lead to more transient router errors than routers using simple XY routing algorithm. We exploit the inherent information redundancy (IIR) in LBDRhr logic to manage transient errors in the network routers. Thorough analyses are provided to discover the appropriate internal nodes and the forbidden signal patterns for transient error detection. Simulation results show that LBDRhr logic can tolerate all of the permanent failure combinations of long-range links and 80% of links failures at short-range links. Case studies show that the error detection method based on the new IIR extraction method reduces the power consumption and the residual error rate by 33% and up to two orders of magnitude, respectively, compared to triple modular redundancy. The impact of network topologies on the efficiency of the detection mechanism has been examined in this work, as well
Exploiting Network-on-Chip Structural Redundancy for A Cooperative and Scalable Built-In Self-Test Architecture
This paper proposes a built-in self-test/self-diagnosis procedure at start-up of an on-chip network (NoC). Concurrent BIST operations are carried out after reset at each switch, thus resulting in scalable test application time with network size. The key principle consists of exploiting the inherent structural redundancy of the NoC architecture in a cooperative way, thus detecting faults in test pattern generators too. At-speed testing of stuck-at faults can be performed in less than 1200 cycles regardless of their size, with an hardware overhead of less than 11%
Methodologies and Toolflows for the Predictable Design of Reliable and Low-Power NoCs
There is today the unmistakable need to evolve design methodologies and
tool
ows for Network-on-Chip based embedded systems. In particular, the
quest for low-power requirements is nowadays a more-than-ever urgent dilemma.
Modern circuits feature billion of transistors, and neither power management
techniques nor batteries capacity are able to endure the increasingly higher
integration capability of digital devices. Besides, power concerns come together
with modern nanoscale silicon technology design issues.
On one hand, system failure rates are expected to increase exponentially at
every technology node when integrated circuit wear-out failure mechanisms
are not compensated for. However, error detection and/or correction mechanisms
have a non-negligible impact on the network power.
On the other hand, to meet the stringent time-to-market deadlines, the design
cycle of such a distributed and heterogeneous architecture must not be
prolonged by unnecessary design iterations.
Overall, there is a clear need to better discriminate reliability strategies and
interconnect topology solutions upfront, by ranking designs based on power
metric. In this thesis, we tackle this challenge by proposing power-aware
design technologies.
Finally, we take into account the most aggressive and disruptive methodology
for embedded systems with ultra-low power constraints, by migrating
NoC basic building blocks to asynchronous (or clockless) design style. We
deal with this challenge delivering a standard cell design methodology and
mainstream CAD tool
ows, in this way partially relaxing the requirement
of using asynchronous blocks only as hard macros
CROSS-LAYER DESIGN, OPTIMIZATION AND PROTOTYPING OF NoCs FOR THE NEXT GENERATION OF HOMOGENEOUS MANY-CORE SYSTEMS
This thesis provides a whole set of design methods to enable and manage the
runtime heterogeneity of features-rich industry-ready Tile-Based Networkon-
Chips at different abstraction layers (Architecture Design, Network Assembling,
Testing of NoC, Runtime Operation). The key idea is to maintain
the functionalities of the original layers, and to improve the performance
of architectures by allowing, joint optimization and layer coordinations. In
general purpose systems, we address the microarchitectural challenges by codesigning
and co-optimizing feature-rich architectures. In application-specific
NoCs, we emphasize the event notification, so that the platform is continuously
under control. At the network assembly level, this thesis proposes a
Hold Time Robustness technique, to tackle the hold time issue in synchronous
NoCs. At the network architectural level, the choice of a suitable synchronization
paradigm requires a boost of synthesis flow as well as the coexistence
with the DVFS. On one hand this implies the coexistence of mesochronous
synchronizers in the network with dual-clock FIFOs at network boundaries.
On the other hand, dual-clock FIFOs may be placed across inter-switch links
hence removing the need for mesochronous synchronizers. This thesis will
study the implications of the above approaches both on the design flow and
on the performance and power quality metrics of the network. Once the manycore
system is composed together, the issue of testing it arises. This thesis
takes on this challenge and engineers various testing infrastructures. At the
upper abstraction layer, the thesis addresses the issue of managing the fully
operational system and proposes a congestion management technique named
HACS. Moreover, some of the ideas of this thesis will undergo an FPGA
prototyping. Finally, we provide some features for emerging technology by
characterizing the power consumption of Optical NoC Interfaces
Design and Validation of Network-on-Chip Architectures for the Next Generation of Multi-synchronous, Reliable, and Reconfigurable Embedded Systems
NETWORK-ON-CHIP (NoC) design is today at a crossroad. On one hand, the
design principles to efficiently implement interconnection networks in the
resource-constrained on-chip setting have stabilized. On the other hand,
the requirements on embedded system design are far from stabilizing. Embedded
systems are composed by assembling together heterogeneous components featuring
differentiated operating speeds and ad-hoc counter measures must be adopted
to bridge frequency domains. Moreover, an unmistakable trend toward enhanced
reconfigurability is clearly underway due to the increasing complexity of applications.
At the same time, the technology effect is manyfold since it provides unprecedented
levels of system integration but it also brings new severe constraints
to the forefront: power budget restrictions, overheating concerns, circuit delay and
power variability, permanent fault, increased probability of transient faults.
Supporting different degrees of reconfigurability and flexibility in the parallel
hardware platform cannot be however achieved with the incremental evolution of
current design techniques, but requires a disruptive approach and a major increase
in complexity. In addition, new reliability challenges cannot be solved by using
traditional fault tolerance techniques alone but the reliability approach must be
also part of the overall reconfiguration methodology.
In this thesis we take on the challenge of engineering a NoC architectures for
the next generation systems and we provide design methods able to overcome the
conventional way of implementing multi-synchronous, reliable and reconfigurable
NoC. Our analysis is not only limited to research novel approaches to the specific
challenges of the NoC architecture but we also co-design the solutions in a single
integrated framework. Interdependencies between different NoC features are
detected ahead of time and we finally avoid the engineering of highly optimized solutions
to specific problems that however coexist inefficiently together in the final
NoC architecture. To conclude, a silicon implementation by means of a testchip
tape-out and a prototype on a FPGA board validate the feasibility and effectivenes