Testing for delay defects utilizing test data compression techniques

textAs technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of smaller delay defects; these defects can cause functional behavior to fail and also indicate potential reliability issues. The first part of this dissertation addresses these problems by presenting an enhanced timing-based delay fault testing technique that incorporates the use of standard delay ATPG, along with timing information gathered from standard static timing analysis. Utilizing delay fault patterns typically increases the test data volume by 3-5X when compared to stuck-at patterns. Combined with the increase in test data volume associated with the increase in gate count that typically accompanies the miniaturization of technology, this adds up to a very large increase in test data volume that directly affect test time and thus the manufacturing cost. The second part of this dissertation presents a technique for improving test compression and reducing test data volume by using multiple expansion ratios while determining the configuration of the scan chains for each of the expansion ratios using a dependency analysis procedure that accounts for structural dependencies as well as free variable dependencies to improve the probability of detecting faults. Finally, this dissertation addresses the problem of unknown values (X’s) in the output response data corrupting the data and degrading the performance of the output response compactor and thus the overall amount of test compression. Four techniques are presented that focus on handling response data with large percentages of X’s. The first uses X-canceling MISR architecture that is based on deterministically observing scan cells, and the second is a hybrid approach that combines a simple X-masking scheme with the X-canceling MISR for further gains in test compression. The third and fourth techniques revolve around reiterative LFSR X-masking, which take advantage of LFSR-encoded masks that can be reused for multiple scan slices in novel ways.Electrical and Computer Engineerin

Reducing Library Characterization Time for Cell-aware Test while Maintaining Test Quality

Cell-aware test (CAT) explicitly targets faults caused by defects inside library cells to improve test quality, compared with conventional automatic test pattern generation (ATPG) approaches, which target faults only at the boundaries of library cells. The CAT methodology consists of two stages. Stage 1, based on dedicated analog simulation, library characterization per cell identifies which cell-level test pattern detects which cell-internal defect; this detection information is encoded in a defect detection matrix (DDM). In Stage 2, with the DDMs as inputs, cell-aware ATPG generates chip-level test patterns per circuit design that is build up of interconnected instances of library cells. This paper focuses on Stage 1, library characterization, as both test quality and cost are determined by the set of cell-internal defects identified and simulated in the CAT tool flow. With the aim to achieve the best test quality, we first propose an approach to identify a comprehensive set, referred to as full set, of potential open- and short-defect locations based on cell layout. However, the full set of defects can be large even for a single cell, making the time cost of the defect simulation in Stage 1 unaffordable. Subsequently, to reduce the simulation time, we collapse the full set to a compact set of defects which serves as input of the defect simulation. The full set is stored for the diagnosis and failure analysis. With inspecting the simulation results, we propose a method to verify the test quality based on the compact set of defects and, if necessary, to compensate the test quality to the same level as that based on the full set of defects. For 351 combinational library cells in Cadence’s GPDK045 45nm library, we simulate only 5.4% defects from the full set to achieve the same test quality based on the full set of defects. In total, the simulation time, via linear extrapolation per cell, would be reduced by 96.4% compared with the time based on the full set of defects

New techniques for functional testing of microprocessor based systems

Electronic devices may be affected by failures, for example due to physical defects. These defects may be introduced during the manufacturing process, as well as during the normal operating life of the device due to aging. How to detect all these defects is not a trivial task, especially in complex systems such as processor cores. Nevertheless, safety-critical applications do not tolerate failures, this is the reason why testing such devices is needed so to guarantee a correct behavior at any time. Moreover, testing is a key parameter for assessing the quality of a manufactured product. Consolidated testing techniques are based on special Design for Testability (DfT) features added in the original design to facilitate test effectiveness. Design, integration, and usage of the available DfT for testing purposes are fully supported by commercial EDA tools, hence approaches based on DfT are the standard solutions adopted by silicon vendors for testing their devices. Tests exploiting the available DfT such as scan-chains manipulate the internal state of the system, differently to the normal functional mode, passing through unreachable configurations. Alternative solutions that do not violate such functional mode are defined as functional tests. In microprocessor based systems, functional testing techniques include software-based self-test (SBST), i.e., a piece of software (referred to as test program) which is uploaded in the system available memory and executed, with the purpose of exciting a specific part of the system and observing the effects of possible defects affecting it. SBST has been widely-studies by the research community for years, but its adoption by the industry is quite recent. My research activities have been mainly focused on the industrial perspective of SBST. The problem of providing an effective development flow and guidelines for integrating SBST in the available operating systems have been tackled and results have been provided on microprocessor based systems for the automotive domain. Remarkably, new algorithms have been also introduced with respect to state-of-the-art approaches, which can be systematically implemented to enrich SBST suites of test programs for modern microprocessor based systems. The proposed development flow and algorithms are being currently employed in real electronic control units for automotive products. Moreover, a special hardware infrastructure purposely embedded in modern devices for interconnecting the numerous on-board instruments has been interest of my research as well. This solution is known as reconfigurable scan networks (RSNs) and its practical adoption is growing fast as new standards have been created. Test and diagnosis methodologies have been proposed targeting specific RSN features, aimed at checking whether the reconfigurability of such networks has not been corrupted by defects and, in this case, at identifying the defective elements of the network. The contribution of my work in this field has also been included in the first suite of public-domain benchmark networks