Overview of the JET results in support to ITER

The 2014–2016 JET results are reviewed in the light of their significance for optimising the ITER research plan for the active and non-active operation. More than 60 h of plasma operation with ITER first wall materials successfully took place since its installation in 2011. New multi-machine scaling of the type I-ELM divertor energy flux density to ITER is supported by first principle modelling. ITER relevant disruption experiments and first principle modelling are reported with a set of three disruption mitigation valves mimicking the ITER setup. Insights of the L–H power threshold in Deuterium and Hydrogen are given, stressing the importance of the magnetic configurations and the recent measurements of fine-scale structures in the edge radial electric. Dimensionless scans of the core and pedestal confinement provide new information to elucidate the importance of the first wall material on the fusion performance. H-mode plasmas at ITER triangularity (H = 1 at βN ~ 1.8 and n/nGW ~ 0.6) have been sustained at 2 MA during 5 s. The ITER neutronics codes have been validated on high performance experiments. Prospects for the coming D–T campaign and 14 MeV neutron calibration strategy are reviewed.European Commission (EUROfusion 633053

Plasma-Wall Interaction

The control of wall loads in fusion devices, in particular with respect to the life time limitations of wall components due to material erosion and migration, will be decisive for the realisation of a fusion power plant operating in steady state. In ITER the primary goal for plasma-wall interaction is the achievement of a high availability of this pulsed experiment. The article describes the grand challenges of plasma-wall interaction research along the needs for ITER and the strategies of ongoing research for further optimization of the design. Addressed are questions related to material problems, erosion- and transport processes, tritium retention in deposited layers and problems transient heat loads

Overview of the JET results in support to ITER

The 2014–2016 JET results are reviewed in the light of their significance for optimising the ITER research plan for the active and non-active operation. More than 60 h of plasma operation with ITER first wall materials successfully took place since its installation in 2011. New multi-machine scaling of the type I-ELM divertor energy flux density to ITER is supported by first principle modelling. ITER relevant disruption experiments and first principle modelling are reported with a set of three disruption mitigation valves mimicking the ITER setup. Insights of the L–H power threshold in Deuterium and Hydrogen are given, stressing the importance of the magnetic configurations and the recent measurements of fine-scale structures in the edge radial electric. Dimensionless scans of the core and pedestal confinement provide new information to elucidate the importance of the first wall material on the fusion performance. H-mode plasmas at ITER triangularity (H  =  1 at β N ~ 1.8 and n/n GW ~ 0.6) have been sustained at 2 MA during 5 s. The ITER neutronics codes have been validated on high performance experiments. Prospects for the coming D–T campaign and 14 MeV neutron calibration strategy are reviewed

ERO modelling of tungsten erosion in the linear plasma device PSI-2

Proceedings of the 22nd International Conference on Plasma Surface Interactions 2016, 22nd PSISeries of experiments on tungsten (W) erosion and transport in Argon (Ar) plasma were conducted at the linear plasma device PSI-2. W erosion was measured with three independent methods: WΙ spectroscopy, mass loss and quartz micro-balance (QMB) deposition sensor. Consistent set of data produced in these experiments was interpreted using the 3D ERO code simulations, which have reproduced all the main trends observed. Influence of the physical model assumptions (e.g. energy and angular distributions of sputtered particles) was demonstrated. The effect of WΙ effective quasi-metastable (MS) state population dynamics on spectroscopy measurements is shown; the characteristic relaxation time is determined. The measured physical sputtering yields for W are close to the simulated data obtained in the binary collision approximation (BCA) approach (SDTrimSP code). The remaining discrepancies between simulations and the experiment, mostly in spectroscopy, are accounted to the uncertainties in the plasma parameters and atomic data.Peer reviewe

Improved ERO modelling for spectroscopy of physically and chemically assisted eroded beryllium from the JET-ILW

Physical and chemical assisted physical sputtering were characterised by the Be I and Be II line and BeD band emission in the observation chord measuring the sightline integrated emission in front of the inner beryllium limiter at the torus midplane. The 3D local transport and plasma-surface interaction Monte- Carlo modelling (ERO code [18] ) is a key for the interpretation of the observations in the vicinity of the shaped solid Be limiter. The plasma parameter variation (density scan) in limiter regime has provided a useful material for the simulation benchmark. The improved background plasma parameters input, the new analytical expression for particle tracking in the sheath region and implementation of the BeD re- lease into ERO has helped to clarify some deviations between modelling and experiments encountered in the previous studies [4,5] . Reproducing the observations provides additional confidence in our ‘ERO-min’ fit for the physical sputtering yields for the plasma-wetted areas based on simulated data.EURATOM 63305

Improved ERO modelling of beryllium erosion at ITER upper first wall panel using JET-ILW and PISCES-B experience

ERO is a 3D Monte-Carlo impurity transport and plasma-surface interaction code. In 2011 it was applied for the ITER first wall (FW) life time predictions [1] (critical blanket module BM11). After that the same code was significantly improved during its application to existing fusion-relevant plasma devices: the tokamak JET equipped with an ITER-like wall and linear plasma device PISCES-B. This has allowed testing the sputtering data for beryllium (Be) and showing that the “ERO-min” fit based on the large (50%) deuterium (D) surface content is well suitable for plasma-wetted areas (D plasma). The improved procedure for calculating of the effective sputtering yields for each location along the plasma-facing surface using the recently developed semi-analytical sheath approach was validated. The re-evaluation of the effective yields for BM11 following the similar revisit of the JET data has indicated significant increase of erosion and motivated the current re-visit of ERO simulations.EURATOM 63305