High-speed Energy-efficient Soft Error Tolerant Flip-flops

Single event upset (SEU) or soft error caused by alpha particles and cosmic neutrons has emerged as a key reliability concern in nanoscale CMOS technologies. The decrease in signal charge due to the reduction of the operating voltage and node capacitance primarily increases the soft error rate (SER) in integrated circuits. The situation is aggravated by the increasing number of memory elements (e.g., flip-flops) on chip, the lack of inherent error masking mechanisms in these elements, and the below-nominal voltage operation for reducing the power consumption. In fact, limiting the power consumption is critical to enhance the battery life of portable electronic devices. In this thesis, I present several soft error tolerant flip-flops that offer high speed while consuming low power either inherently or through low-energy clocking scheme. The proposed soft error tolerant flip-flops can be divided into two major categories: i) flip-flops with square-wave clock and ii) flip-flops with energy recovery sinusoidal clock, which is very attractive to significantly lower the clock power consumption. The two square-wave clock based proposed flip-flops are: a true single phase clock (TSPC) DICE flip-flop and a clocked precharge soft error robust flip-flop. These flip-flops use fewer transistors and offer as much as 35% lower power-delay-product (PDP) than existing soft error robust pulsed DICE flip-flop. The energy recovery clock based proposed flip-flops are: a soft clock edge SEU hardened (SCESH) flip-flop, C2-DICE flip-flop, a conditional pass Quatro (CPQ) flip-flop, and two energy recovery TSPC flip-flops. These flip-flops exhibit lower PDP ranging from 30% to 69% when compared to the pulsed DICE flip-flop and the single-ended conditional capturing energy recovery (SCCER) flip-flop. Thus, the proposed flip-flops provide a wide range of power and delay choices and as such can be used in a variety of low-power or high performance applications including high-end microprocessors, low-power system-on-chips (SOCs), and implantable medical devices

Power Reduction Techniques in Clock Distribution Networks with Emphasis on LC Resonant Clocking

In this thesis we propose a set of independent techniques in the overall concept of LC resonant clocking where each technique reduces power consumption and improve system performance. Low-power design is becoming a crucial design objective due to the growing demand on portable applications and the increasing difficulties in cooling and heat removal. The clock distribution network delivers the clock signal which acts as a reference to all sequential elements in the synchronous system. The clock distribution network consumes a considerable amount of power in synchronous digital systems. Resonant clocking is an emerging promising technique to reduce the power of the clock network. The inductor used in resonant clocking enables the conversion of the electric energy stored on the clock capacitance to magnetic energy in the inductor and vice versa. In this thesis, the concept of the slack in the clock skew has been extended for an LC fully-resonant clock distribution network. This extra slack in comparison to standard clock distribution networks can be used to reduce routing complexity, achieve reduction in wire elongation, total wire length, and power consumption. Simulation results illustrate that by utilizing the proposed approach, an average reduction of 53% in the number of wire elongations and 11% reduction in total wire length can be achieved. A dual-edge clocking scheme introduced in the literature to enable the operation of the flip-flop at the rising- and falling edges of the clock has been modified. The interval by which the charging elements in the flip-flop are being switched-on was reduced causing a reduction in power consumption. Simulating the flip-flop in STMicroelectronics 90-nm technology shows correct functionality of the Sense Amplifier flip-flop with a resonant clock signal of 500 MHz and a throughput of 1 GHz under process, voltage, and temperature (PVT) variations. Modeling the resonant system with the proposed flip-flop illustrates that dual-edge compared to single-edge triggering can achieve up to 58% reduction in power consumption when the clock capacitance is the dominating factor. The application of low-swing clocking to LC resonant clock distribution network has been investigated on-chip. The proposed low-swing resonant clocking scheme operates with one voltage supply and does not require an additional supply voltage. The Differential Conditional Capturing flip-flop introduced in the literature was modified to operate with a low-swing sinusoidal clock. Low-swing resonant clocking achieved around 5.8% reduction in total power with 5.7% area overhead. Modeling the clock network with the proposed flip-flop illustrates that low-swing clocking can achieve up to 58% reduction in the power consumption of the resonant clock. An analytical approach was introduced to estimate the required driver strength in the clock generator. Using the proposed approach early in the design stage reduces area and power overhead by eliminating the need for programmable switches in the driving circuit